Mitsubishi Lancer Evolution VII Manual de usuario

EXTERIOR – GENERAL 51-1

SECTION 51

EXTERIOR

CONTENTS

GENERAL

New servicing information now applies with the following changes and additions. Apart from the information below, servicing is

the same as the Lancer Evolution VII.

• Changes in the shape of the front bumper and addition of new components

• Addition of components due to changes in rear spoiler shape, and change in the positioning of double-sided adhesive tape

• Change in the shape of three diamond mark, EVOLUTION mark and LANCER mark, and change in the positioning of

EVOLUTION mark and LANCER mark.

Gene al .......................................................1

F ont bumpe ...........................................2

Adhesives................................................2

Front bumper ..........................................2

Rea spoile ...............................................4

Adhesive .................................................4

Rear spoiler ............................................

Ma ks ..........................................................6

EXTERIOR – FRONT BUMPER

51-2

F ont Bumpe

Adhesive

F ont bumpe

Removal and Installation

Removal p ocedu e

1. Side under cover

2. Centre under cover

3. Under cover centre bracket

4. Front under cover

• Splash shield installation clip

• Water spray hose connection (see Chapter 1 )

. Front bumper assembly

Section A-A

clip

Section B-B

clip

Section C-C

Application Brand

Three Diamond Mark Double-sided tape: Generic product (width 20 mm, thickness 0.8 mm)

fender

EXTERIOR – FRONT BUMPER 51-3

Double-sided tape: Gene ic tape

Width: 20 mm; Thickness 0.8 mm

Disassembly and Reassembly

Clip

Section A-A Section B-B

EXTERIOR – FRONT BUMPER, REAR SPOILER

51-4

Disassembly P ocedu e

1. Three diamond mark

2. Licence plate trim

3. Licence plate bracket

4. Licence plate bracket assembly

. Cover

6. Front air dam panel

7. Front bumper lower plate assembly

8. Front bumper lower reinforcement

assembly

9. Front bumper reinforcement assembly

10.Bumper net

11. Front bumper side cover

12. Bumper side net (LH)

13. Oil cooler duct

14. Bumper side net (RH)

• Water spray hose and nozzle

(see Chap. 1 )

1 . Front bumper side plate assembly

16. Front bumper upper reinforcement

assembly

17. Front bumper face

Disassembly se vice points

ARemoval of f ont bumpe side plate

Use the same procedure as that for removal of front bumper rivets

in previous model.

Reassembly se vice points

A Installation of f ont bumpe side plate

Use the same procedure as that for installation of front bumper

rivets in previous model.

Rea Spoile

Adhesive

AA

Application Brand

Rear Spoiler Double-sided tape : Generic product A (width mm, thickness 0.8 mm); B (width mm,

thickness 1.2 mm)

Double-sided tape removing agent : Sumitomo 3M 4000 double-sided tape remover (made

by Sumitomo 3M)

Primer : Sumitomo 3M 8107 parts primer (made by Sumitomo 3M)

EXTERIOR – REAR SPOILER 51-5

Rea Spoile

Removal and Installation

Removal p ocedu e

• Boot lid bumper

1. Cap

2. Rear spoiler

Double-sided tape: Gene ic p oducts A: width 5 mm, thickness 0.8 mm,

B: width 5 mm, thickness 1.2 mm

P ime : Sumitomo 3M 8107 PP pa ts p ime

Remarks :

The removal and installation service points are the same as those for the air dam, bumper moulding, wing and door moulding

in the previous model.

AA

EXTERIOR – MARKS

51-6

Ma ks

Removal and Installation

1. Three diamond mark

A2. LANCER mark

A 3. EVOLUTION mark

Installation se vice points

AInstallation of ma ks

1. Installation position

(2) LANCER ma k

Boot lid end line

EXTERIOR – MARKS 51-7

(3) EVOLUTION mark

2. Installation p ocedu e

(1) Remove grease from installation surface of the body, using unleaded

gasoline.

(2) Peel off the protective backing of the mark and apply it to the installation

position.

Caution

1) Pe fo m this ope ation in a dust-f ee envi onment at a oom tempe atu e

of 20 – 38°C.

2) If the oom tempe atu e is less than 20°C, then the ma k and body

(installation position) must be heated to 20 – 30°C.

3) The ma k must be p essed to eliminate any ai bubbles.

Boot lid end line

Tabla de contenidos

Otros manuales de Automóvil de Mitsubishi

Mitsubishi

Mitsubishi 1993 3000GT Documento técnico

Mitsubishi

Mitsubishi LANCER EVOLUTION 2003 Instrucciones de funcionamiento

Mitsubishi

Mitsubishi ECLIPSE Manual de usuario

Mitsubishi

Mitsubishi Pajero Sport 1996 Manual de instrucciones

Mitsubishi

Mitsubishi Mirage 2015 Manual de instrucciones

Mitsubishi

Mitsubishi 2018 ECLIPSE CROSS Guía del usuario

Mitsubishi

Mitsubishi i-MiEV Manual de referencia

Mitsubishi

Mitsubishi 2008 passenger car Manual de usuario

Mitsubishi

Mitsubishi ECLIPSE 2011 Manual de usuario

Mitsubishi

Mitsubishi Outlander 2007 Manual de usuario

Mitsubishi

Mitsubishi Outlander PHEV 2019 Guía del usuario

Mitsubishi

Mitsubishi Outlander 2017 Manual de usuario

Mitsubishi

Mitsubishi 1996 L400 Manual de instrucciones

Mitsubishi

Mitsubishi 1998 FTO Documento técnico

Mitsubishi

Mitsubishi EVO VIII 260 Manual de usuario

Mitsubishi

Mitsubishi LANCER Manual de usuario

Mitsubishi

Mitsubishi LANCER Evolution VIII Manual de instrucciones

Mitsubishi

Mitsubishi Montero 1984 Manual de usuario

Mitsubishi

Mitsubishi ASX 2016 Manual de usuario

Mitsubishi

Mitsubishi 3000GT Manual de instrucciones

Mitsubishi

Mitsubishi 3000GT Manual de usuario

Mitsubishi

Mitsubishi MIrage 2019 Guía del usuario

Mitsubishi

Mitsubishi L200 Manual técnico

Mitsubishi

Mitsubishi 2005 Outlander Guía del usuario

Manuales populares de Automóvil de otras marcas

Toyota

Toyota 2000 Tundra Manual de usuario

CITROËN

CITROËN DS4 DSign Manual de usuario

Lexus

Lexus 2015 CT 200h Manual de usuario

Cadillac

Cadillac CTS 2008 Manual de usuario

Mercedes-Benz

Mercedes-Benz M-class ML 55 AMG Manual de usuario

Porsche

Porsche Boxster S Manual de usuario

GMC

GMC 2010 Savana 1500 Cargo Manual de usuario

KIAM

KIAM SPORTAGE 2014 Manual de lista de piezas

GMC

GMC 2013 Terrain Instrucciones de montaje

GMC

GMC T-Series 1999 Manual de usuario

Mercury

Mercury 1998 Mystique Manual de usuario

Mercury

Mercury 2007 Mariner Manual de usuario

Mazda

Mazda 2007 Mazdaspeed 3 Guía

Mazda

Mazda 2014 CX-5 Manual de usuario

GMC

GMC Chevrolet Express 2022 Manual de usuario

GMC

GMC 1997 Jimmy Manual de usuario

Chevrolet

Chevrolet 2012 Malibu Manual de usuario

Cadillac

Cadillac 2010 Escalade Manual de usuario