Mitsubishi Electric D700-SC Instrucciones de uso

This guide is intended to complement the user manual provided by the manufacturer.

It is provided as a basic introduction to the product for Inverter Drive Supermarket customers.

It should not be used as a replacement for the manual issued by the manufacturer.

Issue 1

20180129

This product is not a safety device. All safety considerations including but not

limited to Emergency Stop provision should be assessed separately and are

outside the scope of this guide.

Mitsubishi D700-SC Frequency Inverter

Easy Start Guide

The Mitsubishi D700-SC Frequency Inverter range is

available to order from inverterdrive.com

Easy Start Guide

Page 1

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6

Page 7

Page 8

Page 9

Page 10

Page 11

Page 12

Page 13

Page 14

Contents

Power and Motor Connections (Single Phase)

Power and Motor Connections (Three Phase)

Motor Connections - Star and Delta

Parameters - Overview

Parameters to set before use

How to set a Parameter value

How to Operate the Inverter from the keypad

How to enable Sensorless Vector mode

How to connect and configure a Potentiometer

for remote speed control

How to connect and configure a Run Forward or

Run Reverse switch

How to connect and configure a Run/Stop switch

with Forward/Reverse selection

How to configure “3-Wire” control with Run/Stop

pushbuttons and Forward/Reverse selection

Brake Resistor Connection

How to Reset the Inverter to Factory Defaults

Contents

Mitsubishi D700-SC Series Inverter

Easy Start Guide

1. Power and Motor Connections (Single Phase)

Page 2

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

Notes:

The illustration above is based on the smaller

230V Single Phase frame size model (to

0.75kW). The terminal layout for larger 1.5kW

and 2.2kW frame sizes are similar.

The order of the three output phases

determines the direction the motor turns.

Important:

Use screened cable between the Inverter and

Motor. To minimise electromagnetic

interference, ensure the cable screen is

grounded.

The supply must match the Inverter

specification.

Before commencing, confirm that the Inverter and

all cables are completely isolated from the power

supply, have been isolated for at least 5 minutes

and that the motor is not turning.

Mitsubishi D700-SC Series Inverter

Live

Neutral

Earth

Phase

Earth

N/- P1 P/+ PR

T/L3R/L1 S/L2 UVW

MotorPower

Do not remove jumper

between terminals P1 and P/+

Easy Start Guide

2. Power and Motor Connections (Three Phase)

Page 3

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

Notes:

The illustration above is based on the smaller

400V Three Phase frame size model (to

3.7kW). The terminal layout for larger 5.5kW

and 7.5kW frame sizes is similar.

The order of the three motor phases

determines the direction the motor turns.

The order of the three power phases is

unimportant.

Important:

Use screened cable between the Inverter and

Motor. To minimise electromagnetic

interference, ensure the cable screen is

grounded.

The supply must match the Inverter

specification.

Before commencing, confirm that the Inverter and

all cables are completely isolated from the power

supply, have been isolated for at least 5 minutes

and that the motor is not turning.

Mitsubishi D700-SC Series Inverter

N/- P/+

PR P1

Do not remove jumper between

terminals P1 and P/+

MotorPower

T/L3R/L1 S/L2 UVW

Phase

Earth

Phase

Earth

Easy Start Guide

3. Motor Connections - Star and Delta

Page 4

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

3.2 Motor connected in DELTA:

The link configuration is shown in the

illustration opposite and is sometimes referred

to as “three-a-breast”.

The order of the three phases determines the

direction the motor turns.

Note that the cable screen and earth are

connected together at the earth terminal.

3.1 Motor connected in STAR (or Wye):

For safety purposes, Star (shown opposite) is

the default configuration for new motors and is

sometimes known as “two at one side”.

Only two links are required for Star. Double-up

the links if changing from Delta to allow the

motor to be changed to back in future.

The order of the three phases determines the

direction the motor turns.

Note that the cable screen and earth are

connected together at the earth terminal.

Dual voltage induction motors typically include

terminal boxes with six points. The points can

be connected together with links in one of two

ways to suit one of the two rated voltages.

The two ways of connecting the links are

shown below. These are known as “Star” (the

higher voltage) or “Delta” (the lower voltage).

The selection of Star or Delta is not optional

and must match the supply voltage.

Dual voltage motor nameplates include

symbols to represent voltage and full load

current in each configuration.

Delta is represented by a triangle and star by a

Y (Wye).

Mitsubishi D700-SC Series Inverter

Phase

Earth

Screen

Phase

Earth

Screen

Link DELTA

STAR

Link

Easy Start Guide

Page 5

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

4. Parameters - overview

Parameter

Description

How to set

Pr. 1

Maximum Frequency (Hz)

Maximum frequency of the . Default is 120. Set to for most applications.Inverter 50

Pr. 2

Minimum Frequency (Hz)

Minimum frequency of the . Default is 0. Set to for most applications.Inverter 5

Pr. 3

Base Frequency (Hz)

Inverter output frequency at input voltage. Normally Hz50 .

Pr. 7

Acceleration time (seconds)

Default is or . Increase or decrease if faster or slower acceleration is required.510

Pr. 8

Deceleration time (seconds)

Default is or . Increase or decrease if faster or slower deceleration is required.510

Pr. 9

Electronic thermal O/L relay (A)

Rated current of the . Set to match motor nameplate - eg.Motor 3.34 Amps

Pr. 13

Starting frequency (Hz)

Frequency at which the Inverter will start the motor. Default is . Change if required.0.5

Pr. 14

Load pattern selection

Default is (most applications). Set to 1 for fan or centrifugal pump applications.0

Pr. 72

PWM Frequency selection (kHz)

Set to for motor cable lengths to 50m or 8 for 50-100m or 2 for 100m+.15

Pr. 79

Operation mode selection

Set to to allow control to be switched between Inverter Keypad (PU) and Terminals (EXT).0

Pr. 83

Rated motor voltage

Rated voltage of the . Set to match motor nameplate - eg.Motor 230 Volts

Pr. 84

Rated motor frequency (Hz)

Rated frequency of the . Set to match motor nameplate - eg.Motor 50 Hz

Pr. 160

Extended function display selection

Set to to display both simple and extended parameters.0

The Inverter contains a number of settings

which can be changed to tailor it for use in a

wide range of applications. These settings are

known as parameters.

Parameters are typically referred to by code or

number (eg. Pr. 9 = Rated Motor Current) with

a description available in the manual.

The parameters contain critical information

essential to the correct operation of the

Inverter. Therefore, they should at least be

checked by the user before the Inverter is

operated for the first time.

The parameters listed in section 5 are intended

to provide a starting point to allow for basic

operation of the D700 SC Inverter.

5. Parameters to set before use

See section 6 to learn how to set a parameter value.

Set the following parameters to allow the D700

SC to control a motor with Run, Stop and

Speed Control from the keypad.

If any of the parameters have been changed

previously, follow the procedure in section 14

to reset the Inverter to Factory Defaults.

5.1 Parameters to check and values to set

Mitsubishi D700-SC Series Inverter

Easy Start Guide

6. How to set a Parameter value

Page 6

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

Mitsubishi D700-SC Series Inverter

6.1 Select “PU” operation mode.

With the motor stopped, press the “PU/EXT” key

repeatedly until the “PU” indicator is illuminated and

“0.00" is displayed.

Note: If the operation mode is not changed to PU the

Inverter will not allow parameter values to be

changed and return an Er. 4 message.

6.2 Change mode to “Parameter setting”.

Press the “MODE” key repeatedly until the “PRM”

indicator is illuminated. The display will show “P. 0” as

shown opposite (or the parameter which was last

selected).

6.3 Select the required parameter.

Use the dial to scroll through the parameters until the

desired parameter is shown. In this example, we will

select parameter 1 (as shown in the illustration opposite).

Press the “Set” key to select the parameter.

6.4 Change the parameter value and set.

The display will show the current parameter value. Use

the dial to increase or decrease the value as required. In

this case we will reduce the value from 120.0 to 50.00.

Press the “SET” key to save the new value. The display

will flash between parameter and value.

Press the “SET” key again to confirm.

Press “SET” one more time to return to the parameter list.

The next parameter in the list is shown.

Easy Start Guide

7. How to operate the Inverter from the keypad

Page 7

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

7.3 Press the green “RUN” key to start the motor.

The green key will start the motor. The time taken for the

motor to accelerate to the desired speed (in seconds) is

proportional to parameter Pr. 7. The “RUN” indicator will

illuminate to indicate that the motor is running.

To change the speed whilst the motor is running, rotate the

dial to select the new speed and press “SET” to confirm.

The motor will accelerate or decelerate to the new speed.

Mitsubishi D700-SC Series Inverter

7.1 Select “MON” and “PU” modes.

With the motor stopped, press the “PU/EXT” key

repeatedly to cycle through operation modes until the

“PU” indicator is illuminated and “0.00" is displayed.

Then, press the “MODE” key repeatedly to cycle through

modes until “MON” is illuminated.

Finally, ensure the display is set to “Hz”. If it is set to “A”

(Amps), use the “SET” key to change to “Hz”.

7.2 Set the desired speed.

Rotate the dial to set the desired speed. In this example,

we have set this to 25.00Hz which is half speed for a

standard 50Hz motor.

Press “SET” to save. The display will alternate between

“F” and your selection for 3 seconds before returning to

0.00 (the current speed). When saving, ensure you don’t

accidentally set the display to “A”. If you do, use the

“SET” key to change back to “Hz”.

7.4 Press the red “Stop” key to stop the motor.

The red key will stop the motor. The time taken (in seconds)

to stop the motor is proportional to parameter Pr. 8.

Note: if you would prefer to continually adjust the speed

using the dial (rather than confirming with set each time)

change parameter Pr. 161 to 1.

8. How to enable Sensorless Vector mode

Page 8

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

The standard motor control mode of the D700

SC Inverter is VxF. This simple mode controls

motor speed by varying Volts and Frequency in

a specific ratio to maintain output torque.

The D700 SC can also operate in Sensorless

Vector mode. This can improve motor

performance without requiring a separate

feedback device. Sensorless Vector mode

operates in the same way as VxF but performs

a number of calculations to improve low speed

torque.

These calculations require an “auto tuning” run

during which the Inverter operates for approx.

10s to gather the necessary data. The shaft

does not turn.

To enable sensorless vector control first set the

parameter values specified in 8.1 and then

perform the auto tuning run described in 8.2

and 8.3.

The motor shaft does not turn during auto

tuning.

Parameter

Description

How to set

Pr. 71

Applied motor

Default is 0. Set to for “Standard motor”.3

Pr. 80

Motor capacity (kW)

Default is 9999 (not set). Set to the motor rated power. eg. kW0.75

Pr. 82

Motor excitation current

Default is 9999 (not set). Set to approx 30% of motor full load current.

Pr. 96

Auto tuning setting/status

Default is 0. Set to for general purpose magnetic flux vector control.11

Pr. 90

Motor constant (R1)

Default is 9999 (not set). Do not change - this value will be set automatically by auto tuning.

8.1 Parameters to change to enable sensorless vector control

Easy Start Guide

Mitsubishi D700-SC Series Inverter

8.2 Enable monitoring and start auto tuning.

Once the parameters in 8.1 have been set, check that the

operation mode is set to “PU”. If not, use the “PU/EXT”

key to cycle through operation modes.

The display will show 11 to indicate that the Inverter is

ready for tuning. Press “RUN” to begin tuning.

The display will show 12 whilst tuning is in progress.

Note: If “Er. 4" is displayed ensure that the operation

mode is set to PU (see above) then press RUN again.

8.3 Auto tuning is complete.

The tuning process will take approx. 10 seconds during

which excitation noise will be heard from the motor.

When the process is complete, the display will show 13 to

indicate normal completion and the “RUN” indicator will

flash. Press “STOP” to complete.

If the display shows 9 auto tuning completed with errors.

Easy Start Guide

Page 9

This guide has been produced by The Inverter Drive Supermarket Ltd.

All content, including but not limited to graphics, text and procedures copyright The Inverter©

Drive Supermarket and must not be reproduced or altered without prior written permission.

9. How to connect and configure a Potentiometer

for remote speed control

Parameter

Description

How to set

Pr. 59

Remote setting function

Default is 0. Set to to enable frequency setpoint via Analogue input terminal 2.1

Pr. 73

Analogue input selection

Set to for 5V (default).1

Pr. 79

External operation mode

Set to to use the Potentiometer as the speed reference with Start/Stop via Inverter keypad.4

Set to 0 to use the Potentiometer as the speed reference with Start/Stop via external controls.

9.1 Parameters to change for remote Potentiometer speed control

If speed control via the integrated dial is

unsuitable for the application, a remote

Potentiometer can be used instead.

This provides the benefit of allowing motor

speed to be controlled from a more convenient

location such as a cabinet door (if the D700 SC

is cabinet-mounted) or on the machine itself.

A Potentiometer of rating should be1kOhm

used.

The number of turns depends on the

application. A single turn Potentiometer is

available from The Inverter Drive Supermarket

at InverterDrive.com.

9.2 Connecting the Potentiometer

First, ensure the Voltage/Current Input switch

is set to “V” (Voltage).

A wiring diagram is shown in the illustration

opposite. The most important connection at

the Potentiometer end is the centre terminal or

“wiper”. The wiper will output a variable voltage

between 0 and 5 volts and should be

connected to the “2" terminal on the Inverter. It

is this voltage which provides the speed signal

with 0V being slowest and 5V fastest.

The default output frequency at 0V is the

minimum frequency of the Inverter. To change

this, edit Parameter 2. The default output

frequency at 5V is 50Hz. To change this, edit

Parameter 125.

If the rotation of the Potentiometer is the

opposite to that required (ie. turn anti-

clockwise to increase speed instead of

clockwise) reverse connections 10 and 5.

Use shielded SY cable between Potentiometer

and Inverter and ensure that the cable screen

is connected to the Inverter earth terminal.

Screened

“SY” Cable

Mitsubishi D700-SC Series Inverter

1kOhm

Potentiometer

[Order Code 31137]

Screen to

Earth Terminal

V I

Voltage/Current

Input Switch

213

Tabla de contenidos

Otros manuales de Accionamiento de CC de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric FR-D700 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A5NPA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric F700 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Melservo-Jet MR-JET-G Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-E500 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-PU07 Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric FR-E800-SCEPA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-F500 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric QnA Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A500 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-F740-00023-EC Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MR-J5W-B Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-D720-0.2K-G Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A 500 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A700 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-CS82S Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A741-5.5K Hoja de instrucciones

Mitsubishi Electric

Mitsubishi Electric FR-D720S SC EC Manual de usuario

Mitsubishi Electric

Mitsubishi Electric fr-e700 series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-800 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-A800 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric FR-F 700 EC Manual de usuario

Manuales populares de Accionamiento de CC de otras marcas

Vincent Associates

Vincent Associates UNIBLITZ ED12DSS Manual de usuario

EKSMA OPTICS

EKSMA OPTICS DQ-100-4 Manual de lista de piezas

Chamberlain Garog

Chamberlain Garog D Series Manual de usuario

Parker

Parker PDS Series Manual de usuario

Festo

Festo DGC G Series Guía de configuración

Binks

Binks QS-5012-1-CE Manual de usuario

Danfoss

Danfoss VLT 2800 Series Hoja de especificaciones

ABB

ABB ACQ580-01 Series Manual de instalación

YASKAWA

YASKAWA CANopen SI-S3 Manual de usuario

GE D20A6 Manual de usuario

Unex

Unex MC-D-250-1000-050W-TW Manual de usuario

Geckodrive

Geckodrive G213V Manual de usuario

ABB

ABB RSYC-01 Manual de usuario

Rockwell Automation

Rockwell Automation PowerFlex 700S Manual del propietario

WEG

WEG DeviceNet CFW500 Manual de usuario

Siemens

Siemens SINAMICS G Hoja de datos

Siemens

Siemens SINAMICS SM150 6SL3815-7NP41-0AA1 Instrucciones de funcionamiento

SOMFY

SOMFY JR RU 30 Manual de usuario