Mitsubishi Electric C80 Series Manual de usuario

Introduction

This manual is a guide for using the MITSUBISHI CNC C80 Series.

This manual describes operations, production processes and maintenances for users who operate the MITSUBISHI CNC

installed machine tool. Read this manual thoroughly before using CNC unit. Moreover study the "Precautions for Safety" on

the next page before use to use the unit safely. Be sure to keep this manual always at hand.

CAUTION

For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the

machine tool builder (MTB) takes precedence over this manual.

Items not described in this manual must be interpreted as "not possible".

This manual is written on the assumption that all the applicable functions are included. Some of them, however,

may not be available for your NC system. Refer to the specifications issued by the machine tool builder before

use.

Refer to the Instruction Manual issued by each MTB for details on each machine tool.

Some screens and functions may differ depending on the NC system (or its version), and some functions may

not be possible. Please confirm the specifications before use.

Do not connect NC system to the Internet-connected network.

To maintain the safety of the NC system against unauthorized access from external devices via the network,

take appropriate measures.

In this manual, the following abbreviations might be used.

L system: Lathe system

M system: Machining center system

MTB: Machine tool builder

Also refer to the manuals on "Manual List" as necessary.

Manual List

Manuals related to M800/M80/E80/C80 Series are listed as follows.

These manuals are written on the assumption that all optional functions are added to the targeted model.

Some functions or screens may not be available depending on the machine or specifications set by MTB. (Confirm the

specifications before use.)

The manuals issued by MTB take precedence over these manuals.

Manual IB No. Purpose and Contents

M800/M80/E80 Series

Instruction Manual IB-1501274 Operation guide for NC

Explanation for screen operation, etc.

C80 Series

Instruction Manual IB-1501453 Operation guide for NC

Explanation for screen operation, etc.

M800/M80/E80/C80 Series

Programming Manual

(Lathe System) (1/2)

IB-1501275 G code programming for lathe system

Basic functions, etc.

M800/M80/E80/C80 Series

Programming Manual

(Lathe System) (2/2)

IB-1501276 G code programming for lathe system

Functions for multi-part system, high-accuracy function, etc.

M800/M80/E80/C80 Series

Programming Manual

(Machining Center System) (1/2)

IB-1501277 G code programming for machining center system

Basic functions, etc.

M800/M80/E80/C80 Series

Programming Manual

(Machining Center System) (2/2)

IB-1501278 G code programming for machining center system

Functions for multi-part system, high-accuracy function, etc.

M800/M80/E80/C80 Series

Alarm/Parameter Manual IB-1501279 Alarms

Parameters

Manuals for MTBs (NC)

Manuals for MTBs (drive section)

Manual IB No. Purpose and Contents

M800/M80/E80/C80 Series

Specifications Manual (Function) IB-1501505 Model selection

Outline of various functions

M800/M80/E80/C80 Series

Specifications Manual (Hardware) IB-1501506 Model selection

Specifications of hardware unit

M800W/M80W Series

Connection and Setup Manual IB-1501268 Detailed specifications of hardware unit

Installation, connection, wiring, setup (startup/adjustment)

M800S/M80/E80 Series

Connection and Setup Manual IB-1501269 Detailed specifications of hardware unit

Installation, connection, wiring, setup (startup/adjustment)

C80 Series

Connection and Setup Manual IB-1501452 Detailed specifications of hardware unit

Installation, connection, wiring, setup (startup/adjustment)

M800/M80/E80 Series

PLC Development Manual IB-1501270

Electrical design

I/O relation (assignment, setting, connection), field network

Development environment (PLC on-board, peripheral

development environment), etc.

M800/M80/E80 Series

PLC Programming Manual IB-1501271

Electrical design

Sequence programming

PLC support functions, etc.

M800/M80/E80/C80 Series

PLC Interface Manual IB-1501272 Electrical design

Interface signals between NC and PLC

M800/M80/E80 Series

Maintenance Manual IB-1501273 Cleaning and replacement for each unit

Other items related to maintenance

C80 Series

Maintenance Manual IB-1501454 Cleaning and replacement for each unit

Other items related to maintenance

Manual IB No. Contents

MDS-E/EH Series

Specifications Manual IB-1501226 Specifications for power supply regeneration type

MDS-E/EH Series

Instruction Manual IB-1501229 Instruction for power supply regeneration type

MDS-EJ/EJH Series

Specifications Manual IB-1501232 Specifications for regenerative resistor type

MDS-EJ/EJH Series

Instruction Manual IB-1501235 Instruction for regenerative resistor type

MDS-EM/EMH Series

Specifications Manual IB-1501238 Specifications for multi-hybrid, power supply regeneration

type

MDS-EM/EMH Series

Instruction Manual IB-1501241 Instruction for multi-hybrid, power supply regeneration type

DATA BOOK IB-1501252 Specifications of servo drive unit, spindle drive unit, motor, etc.

Manuals for MTBs (Others)

■For M800/M80/E80 Series

■For C80 Series

Manual No. Purpose and Contents

GOT2000 Series User’s Manual

(Hardware) SH-081194 Outline of hardware such as part names, external dimensions,

installation, wiring, maintenance, etc. of GOTs

GOT2000 Series User’s Manual

(Utility) SH-081195 Outline of utilities such as screen display setting, operation

method, etc. of GOTs

GOT2000 Series User’s Manual

(Monitor) SH-081196 Outline of each monitor function of GOTs

GOT2000 Series Connection

Manual (Mitsubishi Electric

Products)

SH-081197 Outline of connection types and connection method between

GOT and Mitsubishi Electric connection devices

GT Designer3 (GOT2000) Screen

Design Manual SH-081220 Outline of screen design method using screen creation

software GT Designer3

Manual No. Purpose and Contents

GOT2000/GOT1000 Series CC-Link

Communication Unit User's Manual IB-0800351 Explanation for handling CC-Link communication unit (for

GOT2000 series/GOT1000 series)

GX Developer Version 8 Operating

Manual (Startup) SH-080372E Explanation for system configuration, installation, etc. of PLC

development tool GX Developer

GX Developer Version 8 Operating

Manual SH-080373E Explanation for operations using PLC development tool GX

Developer

GX Converter Version 1 Operating

Manual IB-0800004E Explanation for operations using data conversion tool GX

Converter

MELSEC-Q CC-Link System Master/

Local Module User’s Manual SH-080394E Explanation for system configuration, installation, wiring, etc.

of master/local modules for CC-Link system

GOT2000 Series Connection

Manual (Non-Mitsubishi Electric

Products 1)

SH-081198ENG

Explanation for connection types and connection method

between GOT and other company's devices

GOT2000 Series Connection

Manual (Non-Mitsubishi Electric

Products 2)

SH-081199ENG

GOT2000 Series Connection

Manual (Microcomputers, MODBUS/

Fieldbus Products, Peripherals)

SH-081200ENG

Explanation for connection types and connection method

between GOT and microcomputers, MODBUS/fieldbus

products, peripherals

GT SoftGOT2000 Version1

Operating Manual SH-081201ENG

Explanation for system configuration, screen configuration

and operation method of monitoring software GT

SoftGOT2000

Manual No. Purpose and Contents

MELSEC iQ-R Module Configuration

Manual SH-081262 Outline of system configuration, specifications, installation,

wiring, maintenance, etc.

MELSEC iQ-R CPU Module User’s

Manual (Startup) SH-081263 Outline of specifications, procedures before operation,

troubleshooting, etc. for CPU module

MELSEC iQ-R CPU Module User’s

Manual (Application) SH-081264 Outline of memory, functions, devices, parameters, etc. for

CPU module

QCPU User’s Manual (Hardware

Design, Maintenance and

Inspection)

SH-080483

Outline of specifications, necessary knowledge to configure

the system and maintenance-related descriptions for Q series

CPU module, etc.

GX Works3 Operating Manual SH-081215 Outline of functions, programming, etc.

Reference Manual for MTBs

Manual No. Purpose and Contents

M800/M80 Series Smart safety

observation Specification manual BNP-C3072-022

Explanation for smart safety observation function

C80 Series Smart safety observation

Specification manual BNP-C3077-022

M800/M80 Series CC-Link (Master/

Local) Specification manual BNP-C3072-089 Explanation for CC-Link

M800/M80 Series PROFIBUS-DP

Specification manual BNP-C3072-118 Explanation for PROFIBUS-DP communication function

M800/M80 Series Interactive cycle

insertion (Customization)

Specification manual

BNP-C3072-121-

0003 Explanation for interactive cycle insertion

M800/M80 Series EtherNet/IP

Specifications manual BNP-C3072-263 Explanation for EtherNet/IP

Precautions for Safety

Always read the specifications issued by the MTB, this manual, related manuals and attached documents before installation,

operation, programming, maintenance or inspection to ensure correct use. Understand this numerical controller, safety items

and cautions before using the unit.

This manual ranks the safety precautions into "DANGER", "WARNING" and "CAUTION".

Note that even items ranked as " CAUTION", may lead to major results depending on the situation. In any case, important

information that must always be observed is described.

The following sings indicate prohibition and compulsory.

The meaning of each pictorial sing is as follows.

MITSUBISHI CNC is designed and manufactured solely for applications to machine tools to be used for industrial purposes.

Do not use this product in any applications other than those specified above, especially those which are substantially influential

on the public interest or which are expected to have significant influence on human lives or properties.

Not applicable in this manual.

DANGER

When the user may be subject to imminent fatalities or major injuries if handling is mistaken.

WARNING

When the user may be subject to fatalities or major injuries if handling is mistaken.

CAUTION

When the user may be subject to bodily injury or when physical damage may occur if handling is mistaken.

This sign indicates prohibited behavior (must not do).

For example, "Keep fire away" is indicated by .

This sign indicates a thing that is critical (must do).

For example, "it must be grounded" is indicated by .

CAUTION

CAUTION rotate ob-

ject

CAUTION HOT

Danger Electric

shock risk

Danger explosive

Prohibited

Disassembly is pro-

hibited

KEEP FIRE AWAY

General instruction

Earth ground

For Safe Use

DANGER

WARNING

1. Items related to program development

Do not assign any startup switch for C80 on GOT's touch key. If a communication fault (including cable discon-

nection) occurs between GOT and CNC C80, the communication will be suspended and the GOT will become in-

operative. In this case, even when you release your hands from the startup switch, CNC will fail to recognize the

cutoff of startup signal, which may cause serious accidents.

2. Items related to operation

If the operation start position is set from a block in the program and the program is started, the program before

the set block is not executed. Please confirm that G and F modal and coordinate values are appropriate. If there

are coordinate system shift commands or M, S, T and B commands before the block set as the start position, carry

out the required commands using the MDI, etc. If the program is run from the set block without carrying out these

operations, there is a danger of interference with the machine or of machine operation at an unexpected speed,

which may result in breakage of tools or machine tool or may cause damage to the operators.

Under the constant surface speed control (during G96 modal), if the axis targeted for the constant surface speed

control moves toward the spindle center, the spindle rotation speed will increase and may exceed the allowable

speed of the workpiece or chuck, etc. In this case, the workpiece, etc. may jump out during machining, which may

result in breakage of tools or machine tool or may cause damage to the operators.

CAUTION

1. Items related to product and manual

For items described as "Restrictions" or "Usable State" in this manual, the instruction manual issued by the ma-

chine tool builder (MTB) takes precedence over this manual.

Items not described in this manual must be interpreted as "not possible"

This manual is written on the assumption that all the applicable functions are included. Some of them, however,

may not be available for your NC system. Refer to the specifications issued by the machine tool builder before use.

Refer to the Instruction Manual issued by each MTB for details on each machine tool.

Some screens and functions may differ depending on the NC system (or its version), and some functions may not

be possible. Please confirm the specifications before use.

Do not connect NC system to the Internet-connected network.

To maintain the safety of the NC system against unauthorized access from external devices via the network, take

appropriate measures.

2. Items related to installation and assembly

Ground the signal cables to ensure stable system operation. Also ground the NC unit main frame, power distribu-

tion panel and machine to one point, so they all have the same potential.

3. Items related to preparation before use

Always set the stored stroke limit. Failure to set this could result in collision with the machine end.

Always turn the power OFF before connecting/disconnecting the input/output device cable. Failure to do so could

damage the input/output device and NC unit.

4. Items related to screen operation

If the tool compensation amount or workpiece coordinate system offset amount is changed during automatic op-

eration (including during single block stop), the changes will be valid from the command in next block or after sev-

eral subsequent blocks.

All of the various data in the NC memory is erased when formatting. Be sure to use the transfer function to transfer

all necessary data to another storage device before formatting.

Pay close attention to the sequence operation when carrying out forced data setting (forced output) in the I/F di-

agnosis screen during machine operation.

The program including a character of any language other than the display language is not correctly displayed. Do

not edit such a program. Any part of the program other than the comment part may also be changed if edited.

To prevent influence from data omission and data transformation in the communication circuit, always verify the

data after inputting and outputting machining programs.

Do not change setup parameters without prior approval from the MTB.

5. Items related to programming

If there is no value after the G command, the operation will be the "G00" operation when the program is run due

to key chattering, etc., during editing.

" ; ", "EOB", "%", and "EOR" are symbols used for explanation. The actual codes for ISO are "CR, LF" ("LF") and

"%". "%" and "EOR" are represented by "%" in ISO.

The programs created on the edit screen are stored in the NC memory in a "CR, LF" format, however, the programs

created with external devices may be stored in an "LF" format.

The actual codes for EIA are "EOB (End of Block)" and "EOR (End of Record)".

Do not change the fixed cycle program without prior approval from the MTB.

6. Items related to operation

Do not enter the machine’s movable range during automatic operation. During rotation, keep your hands, feet and

face away from the spindle.

Carry out dry operation before actually machining, and confirm the machining program, tool offset and workpiece

coordinate system offset.

If the operation start position is set from a block in the program and the program is started, the program before

the set block is not executed. If there are coordinate system shift commands or M, S, T, and B commands before

the block set as the starting position, carry out the required commands using the MDI, etc. There is a danger of

interference with the machine if the operation is started from the set starting position block without carrying out

these operations.

Program so the mirror image function is turned ON/OFF at the mirror image center. The mirror image center will

deviate if the function is turned ON/OFF at a position other than the mirror image center.

7.Items related to faults and abnormalities

If the battery low warning is issued in the drive unit side, immediately replace the battery. Replace the batteries

while applying the drive unit's control power.

If the axis overruns or emits an abnormal noise, immediately press the emergency stop button and stop the axis

movement.

Turn OFF the power immediately if any smoke, abnormal noise or odor is generated from the controller, drive unit

or motor.

8. Items related to maintenance

Incorrect connections may damage the devices. Always connect the cables to the indicated connectors.

Do not apply voltages other than those indicated according to specification on the connector. Failure to observe

this could cause bursting, damage, etc.

Do not connect or disconnect the connection cables between each unit while the power is ON.

Do not connect the cable by pulling on the cable wire.

Do not short circuit, charge, overheat, incinerate or disassemble the battery.

Dispose the spent battery according to local laws.

Dispose the spent cooling fan according to local laws.

Do not replace each control unit while the power is ON.

Do not replace the operation panel I/O unit while the power is ON.

Do not replace the cooling fan while the power is ON.

CAUTION

Otros manuales para C80 Series

Tabla de contenidos

Otros manuales de Sistema de control de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric E70 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric M700V Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAC-WHS01WF-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65VBTCU-68DAVN Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Evolution+ s-MEXT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MJ-310E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAR-CT01MAA-SB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J2S Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric BAC-HD150 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAC-YT32PTA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric 700 Series Guía de instalación

Mitsubishi Electric

Mitsubishi Electric Smart ME Controller Manual de usuario

Mitsubishi Electric

Mitsubishi Electric TW-50A Guía rápida

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAR-40MAAU Manual de usuario

Mitsubishi Electric

Mitsubishi Electric M800W Series Guía de configuración

Mitsubishi Electric

Mitsubishi Electric MDS-E Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric par-u02meda Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AL2-EEPROM-2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric M800VW Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric M70V Series Manual de instrucciones

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario