Mitsubishi Electric AE-200A Manual de usuario

Contents

1. Introduction.........................................................................2

1-1. Terms Used in This Manual........................................................2

1-2. PC Requirements.......................................................................2

2. Setting the Operating Environment.....................................3

2-1. Setting the IPAddress of the PC................................................3

2-2. Setting the Web Browser............................................................5

2-3. Java settings...............................................................................8

3. Logging in to the Web Browser for User...........................10

4. Monitor/Operation.............................................................13

4-1. Condition List............................................................................13

Before using the controller, please read this Instruction Book carefully to ensure proper operation.

Retain this manual for future reference.

Instruction Book

–Web Browser for User–

Air Conditioning Control System

Centralized Controller

AE-200A/AE-50A/EW-50A

AE-200E/AE-50E/EW-50E

WT07140X02

1. Introduction

This Instruction Book explains how to monitor and operate the units connected to the AE-200A/AE-50A/EW-50A

and AE-200E/AE-50E/EW-50E using a Web browser.

1-1. Terms Used in This Manual

- “Centralized Controller AE-200A/AE-200E” is referred to as “AE-200.”

- “Centralized Controller AE-50A/AE-50E” is referred to as “AE-50.”

- “Centralized Controller EW-50A/EW-50E” is referred to as “EW-50.”

- “Booster unit” and “Water HEX unit” are referred to as “Air To Water (PWFY) unit.”

- “Hot Water Heat Pump unit” is referred to as “HWHP (CAHV, CRHV) unit.”

- Screen images used in this manual are from Windows 7®and Internet Explorer 9.0.

Note: Windows is a registered trademark or trademark of Microsoft Corporation in the United States and other countries.

1-2. PC Requirements Table1-1 PC Requirements

Item Requirement

CPU 1 GHz or faster

Memory 512 MB or more

Screen resolution 1366 x 768 or higher recommended

Browser

Microsoft®Internet Explorer 8.0

Microsoft®Internet Explorer 9.0

Microsoft®Internet Explorer 10.0

Microsoft®Internet Explorer 11.0

* Java execution environment is required.

(Verified to run on Oracle®Java Plug-in Ver. 1.8.0_25)

* Install Oracle®Java Plug-in that is appropriate for your operating system. When

using a 64-bit OS, install a 32-bit and a 64-bit Java Plug-in.

* The version of the Oracle®Java Plug-in can be verified by clicking [Java] in the

Control Panel.

On-board LAN port or LAN card 100 BASE-TX

Pointing device e.g., mouse

Note: Microsoft is a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.

Oracle and Java are trademarks or registered trademarks of Oracle Inc. in the United States and/or other countries.

Note: Although no particular OS is required, the Web browser will not properly operate when it is started up from the Internet

Explorer on the Windows 8.1 start screen. If the Web browser was started up on the start screen, close the Web browser and

switch the screen to the desktop screen, and then start up the Web browser again. Refer to the help functions of Windows 8.1

for how to switch the screens.

Start screen Desktop screen

WT07140X02

2. Setting the Operating Environment

This chapter explains how to make PC settings and Web browser settings to monitor and operate the air

conditioning units.

2-1. Setting the IP Address of the PC

Follow the instructions below to set the PC’s IP address for the Web browser to recognize the

AE-200/AE-50/EW-50 unit.

The PC’s IP address must have the same network address as the AE-200/AE-50/EW-50’s IP address.

(i.e., AE-200’s IP address: [192.168.1.1], PC’s IP address: [192.168.1.101])

When connecting an AE-200/AE-50/EW-50 to an existing LAN, consult the system administrator to decide the IP

addresses.

Note: When using an AE-200/AE-50/EW-50-dedicated LAN, it is recommended that theAE-200 unit and the EW-50 unit (only

when used alone) be assigned an IP address between the range [192.168.1.1] and [192.168.1.40], theAE-50/EW-50 unit

be assigned an IP address between the range [192.168.1.211] and [192.168.1.249], and that the PC connected to the

AE-200/AE-50/EW-50 be assigned an IP address between the range [192.168.1.101] and [192.168.1.150].

(1) Click [Control Panel] in the Start menu.

(2) Click [Network and Sharing Center]>[Local Area Setting].

In the [Local Area Connection Status] window, click [Properties].

(3) Click [Internet Protocol Version 4 (TCP/IPv4)] to select it, and click

[Properties].

WT07140X02

(4) In the [Internet Protocol Version 4 (TCP/IPv4) Properties] window,

check the radio button next to [Use the following IP address].

Enter the PC’s IP address (e.g., [192.168.1.101]) in the [IP address]

field, and enter the subnet mask [255.255.255.0] (unless otherwise

specified) in the [Subnet mask] field.

In the [Default gateway] field, enter the gateway address as necessary.

Note: Consult the system administrator to decide the IP, subnet mask, and

gateway addresses.

(5) Keep clicking [OK] or [Close] to close all windows.

WT07140X02

2-2. Setting the Web Browser

Web browser setting varies with the Internet connection type. See the sections below for how to make Web

browser settings for different types of Internet connection.

To prevent unauthorized access, always use a security device such as a VPN router when

connecting the AE-200/AE-50/EW-50 to the Internet.

2-2-1. No Internet connection

To monitor and operate the air conditioning units from a PC with no Internet connection, follow the instructions

below to set the environment for the Web browser.

(1) Click [Tools] in the menu bar, then click [Internet options].

(2) In the [Internet Options] window, click the [Connections] tab.

(3) Check the radio button next to [Never dial a connection] in the middle

of the window, and click [OK] to close the window.

WT07140X02

2-2-2. Dial-up Internet connection

To monitor and operate the air conditioning units from a PC that connects to the Internet through a dial-up

connection, follow the instructions below to set the environment for the Web browser.

(1) Click [Tools] in the menu bar, then click [Internet options].

(2) In the [Internet Options] window, click the [Connections] tab.

(3) Check the radio button next to [Dial whenever a network connection

is not present] in the middle of the window, and click [OK] to close the

window.

By making these settings, a message will appear asking whether

or not to use a dial-up connection when an Internet connection is

necessary. Follow the message to connect to the Internet.

2-2-3. Connecting to the Internet via proxy server using an existing LAN

To monitor and operate the air conditioning units from a PC that connects to the Internet through a proxy server

by connecting to an existing LAN, such as a LAN within your company, follow the instructions below to set the

environment for the Web browser.

(1) Click [Tools] in the menu bar, then click [Internet options].

WT07140X02

(2) In the [Internet Options] window, click the [Connections] tab.

(3) Check the radio button next to [Never dial a connection] in the middle

of the window.

(4) Click [LAN settings] under [Local Area Network (LAN) settings].

(5) In the [Local Area Network (LAN) Settings] window, check [Bypass

proxy server for local addresses], and click [Advanced].

(6) In the [Proxy Settings] window, enter the AE-200/AE-50/EW-50’s

IP address (e.g., 192.168.1.1) in the [Exceptions] field. Then, keep

clicking [OK] or [Close] to close all windows.

If connecting multiple AE-200/AE-50/EW-50 units, enter their

addresses (e.g., [192.168.1.1; 192.168.1.2]). It is also possible to use

an asterisk as a wildcard (e.g., [192.168.1.*]).

WT07140X02

2-3. Java settings

2-3-1. How to register exception site list

(1) Click [Control Panel]>[Java].

Note: If [Category] is selected in the top right corner, next to [View by:], change it to [Large icons] or [Small icons].

(2) Java Control Panel will open.

Click the [Security] tab.

(3) The security setting window will open.

Click the [Edit Site List...] button.

(4) The [Exception Site List] dialog will appear.

Click [Add].

(5) The [Exception Site List] dialog will appear.

In the white box, enter the following, and then click [OK].

http://[IP address of AE-200, AE-50, or EW-50]

Note: If the IP address of theAE-200 is [192.168.1.1], enter

[http://192.168.1.1].

 1RWH :KHQXVLQJ+773666/FRQQHFWLRQSUH¿[WKHZHEDGGUHVVZLWK

[https]. (https://[IP address ofAE-200, AE-50, or EW-50])

(6) The security warning screen will appear.

Click [Continue].

Note: The security warning screen will not appear when HTTPS (SSL)

connection is used.

WT07140X02

(7) Add all AE-200/AE-50/EW-50 to the list in the same manner, and

click [OK].

(8) If a PC with 32-bit OS is used, after completing the settings, close all Internet Explorer windows, and access

the Web page again to make sure the appropriate window will appear.

If a PC with 64-bit OS is used, go to step (9) below.

(9) Click [My Computer]>[Local Disk (C:)]>[Program Files (x86)]*1>[Java]>[jre*] (The asterisk indicates a version

number. (i.e., jre1.80_25))>[bin] to open the [bin] folder.

*1 If a PC with 64-bit OS is used, both [Program Files] and [Program Files (x86)] folders will appear. Make sure to select [Program

Files (x86)].

(10)Double click the “javacpl.exe” file in the [bin] folder.

(11) Java Control Panel will open. Follow the steps (3) through (8) again.

2-3-2. How to enable Java content

(1) Open the security setting window. (See section 2-3-1 “How to register exception site list”.)

(2) Click on the checkbox next to [Enable Java content in the browser]

unless it is already checked.

Click [Apply] at the right bottom corner of the screen, and then click

[OK].

(3) After completing the settings, close all Internet Explorer windows, and access the Web page again to make

sure the appropriate window will appear.

WT07140X02

3. Logging in to the Web Browser for User

(1) Enter the web page address in the address field of the Web browser as follows:

http://[IP address of each AE-200, AE-50, or EW-50]/index.html

Press the [Enter] key.A login screen will appear.

Note: If the IP address of theAE-200/AE-50/EW-50 is [192.168.1.1], the

web page address is [http://192.168.1.1/index.html].

Note: Default IP address ofAE-200, AE-50, and EW-50 is [192.168.1.1].

When one or more AE-50/EW-50 controllers are connected,

none of their IP addresses should overlap. The recommended IP

address ranges are as follows.

AE-200: Between [192.168.1.1] and [192.168.1.40]

AE-50/EW-50 (when used for system expansion):

Between [192.168.1.211] and [192.168.1.249]

EW-50 (when used alone):

Between [192.168.1.1] and [192.168.1.40]

Note: Log in to the AE-200, AE-50, or EW-50 Web browser respectively

to monitor or operate the units that are under the control of AE-200,

AE-50, or EW-50. The Web browser cannot be switched among

the AE-200, AE-50, and EW-50.

Note: If the login screen does not appear then take the steps below to

GHOHWHWKHWHPSRUDU\¿OHV

1.Click [Tools] in the menu bar, then click [Internet options].

2.On the [General] tab, click [Delete] in the middle of the window.

3.In the [Delete Browsing History] window, click [Delete].

<Java>

1.Click [Control Panel] from the Start menu.

2.Click the [Java] icon to launch the Java Control Panel.

3.On the [General] tab, click [Settings] in the [Temporary Internet

Files] section.

4.Click [Delete Files].

5.In the [Delete Files and Applications] window, click [OK].

Note: The web page will be displayed in the same language as the operating system on the PC.

The web page can be displayed in other languages by entering the web page address as follows:

Chinese http://[IP address of eachAE-200, AE-50, or EW-50]/zh/index.html

English http://[IP address of eachAE-200, AE-50, or EW-50]/en/index.html

French http://[IP address of eachAE-200, AE-50, or EW-50]/fr/index.html

German http://[IP address of eachAE-200, AE-50, or EW-50]/de/index.html

Italian http://[IP address of eachAE-200, AE-50, or EW-50]/it/index.html

Japanese http://[IP address of eachAE-200, AE-50, or EW-50]/ja/index.html

Portuguese http://[IP address of eachAE-200, AE-50, or EW-50]/pt/index.html

Russian http://[IP address of eachAE-200, AE-50, or EW-50]/ru/index.html

Spanish http://[IP address of eachAE-200, AE-50, or EW-50]/es/index.html

Note: You can add the web page address to your Favorites on the login screen for easy access in the future.

(2) Enter the user name and the password in the login screen, and click [Login]. A Condition List screen will

appear, which shows the operation conditions of groups.

Note: Consult the building manager for your user name and password.

Otros manuales para AE-200A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de control de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric MELDAS 600 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric MEHITS MANAGER 3000+ Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Evolution+ s-MEXT Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELDAS C6 Manual del propietario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAC-YG81TB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric AJ65VBTCU-68DAVN Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELDAS 60 Series Manual del propietario

Mitsubishi Electric

Mitsubishi Electric AE-200A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PAR-CT01MAA-SB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MELDAS FCU6-DX561 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CNC 700 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric LMAP02-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MCCH1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric M800W Series Guía de configuración

Mitsubishi Electric

Mitsubishi Electric MELSERVO-J2S Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric GB-50ADA-J Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAR-40MAA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric E70 Series Manual de instrucciones

Mitsubishi Electric

Mitsubishi Electric AT-50B Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PAR-40MAAU Manual de usuario

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario