Mitsubishi Electric MSZ-HJ25VA-E1 Manual de usuario

CONTENTS

1. TECHNICAL CHANGES ··································· 3

2. PART NAMES AND FUNCTIONS····················· 4

3. SPECIFICATION················································ 5

4. NOISE CRITERIA CURVES······························ 6

5. OUTLINES AND DIMENSIONS ························ 7

6. WIRING DIAGRAM············································ 7

7. REFRIGERANT SYSTEM DIAGRAM··············· 8

8. SERVICE FUNCTIONS ····································· 9

9. MICROPROCESSOR CONTROL ····················11

10. TROUBLESHOOTING····································· 15

11. DISASSEMBLY INSTRUCTIONS···················· 27

MSZ-HJ25VA -E1

MSZ-HJ35VA -E1

MSZ-HJ50VA -E1

Outdoor unit service manual

MUZ-HJ·VA Series (OBH648)

SERVICE MANUAL No. OBH647

REVISED EDITION-A

INDOOR UNIT

PARTS CATALOG (OBB647)

NOTE:

RoHS compliant products have <G> mark on the spec name plate.

SPLIT-TYPE AIR CONDITIONERS

Models

Revision A:

• MSZ-HJ50VA- E1 has been added.

Please void OBH647.

Prepare the proper tools.

Prepare the proper protectors.

Provide adequate ventilation.

After stopping the operation of the air conditioner, turn off the power-supply breaker and remove the power plug.

Discharge the capacitor before the work involving the electric parts.

Do not perform the work involving the electric parts with wet hands.

Do not pour water into the electric parts.

Do not touch the refrigerant.

Do not touch the hot or cold areas in the refrigeration cycle.

When the repair or the inspection of the circuit needs to be done without turning off the power, exercise great caution not to

touch the live parts.

Use the speciﬁed refrigerant only

Never use any refrigerant other than that specified.

Doing so may cause a burst, an explosion, or fire when the unit is being used, serviced, or disposed of.

Correct refrigerant is specified in the manuals and on the spec labels provided with our products.

We will not be held responsible for mechanical failure, system malfunction, unit breakdown or accidents caused by

failure to follow the instructions.

Revision A:

• MSZ-HJ50VA- E1 has been added.

OBH647A

1TECHNICAL CHANGES

MSZ-HJ25VA - E1

MSZ-HJ35VA - E1

MSZ-HJ50VA - E1

1. New model

OBH647A

Operation indicator lamp

Remote control

receiving section

Emergency

operation switch

Horizontal vane

Air inlet

Air ﬁlter

Front panel

Air outlet Heat exchanger

Emergency operation switch

Remote controller

ACCESSORIES

MSZ-HJ25VA MSZ-HJ35VA MSZ-HJ50VA

Installation plate 1

Installation plate ﬁxing screw 4 ×25 mm 5

Battery (AAA) for remote controller 2

Wireless remote controller 1

Felt tape (Used for left or left-rear piping) 1

2PART NAMES AND FUNCTIONS

OBH647A

3SPECIFICATION

Indoor model MSZ-HJ25VA MSZ-HJ35VA MSZ-HJ50VA

Power supply Single phase 230 V, 50 Hz

Breaker Capacity A 10 12

Electrical data

Power input 1 (Total) Cooling W730 1,040 2,050

Heating 870 995 1,480

Running current 1

(Total) Cooling A3.7 4.9 9.0

Heating 4.2 4.8 6.6

Power factor 1 (Total) Cooling %85 92 99

Heating 90 90 97

Starting current 1 (Total) A 4.2 4.9 9.0

Fan motor

Model RC0J40-EF

Current 1 Cooling A0.19 0.24 0.27

Heating 0.20 0.22 0.34

Dimensions W × H × D mm 799 × 290 × 232

Weight kg 9

Special remarks

Air direction 5

Airﬂow

Cooling

Super High

m3/h

571 654 772

High 438 470 667

Med. 328 341 547

Low 227 227 380

Heating

Super High

m3/h

598 619 861

High 451 451 667

Med. 328 328 497

Low 208 208 364

Sound level

Cooling

Super High

dB(A)

43 45 45

High 37 38 40

Med. 30 31 36

Low 22 22 28

Heating

Super High

dB(A)

43 44 47

High 37 37 41

Med. 30 30 34

Low 23 23 27

Fan speed

Cooling

Super High

rpm

1,080 1,200 1,120

High 880 930 1,000

Med. 710 730 860

Low 550 550 660

Heating

Super High

rpm

1,120 1,150 1,220

High 900 900 1,000

Med. 710 710 800

Low 520 520 640

Fan speed regulator 4

Remote controller model MP13A

NOTE : Test conditions are based on ISO 5151.

Cooling : Indoor Dry-bulb temperature 27°C Wet-bulb temperature 19°C

Outdoor Dry-bulb temperature 35°C

Heating : Indoor Dry-bulb temperature 20°C

Outdoor Dry-bulb temperature 7°C Wet-bulb temperature 6°C

1 Measured under rated operating frequency.

Specifications and rated conditions of main electric parts

Fuse (F11) T3.15AL250V

Horizontal vane motor (MV) 12 VDC

Varistor

(NR11)

S10K320E3K1 (ERZV14D471)

Terminal block (TB) 5P

OBH647A

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

COOLING

FUNCTION SPL(dB(A)) LINE

Super High

FAN SPEED

HEATING

NC-10

MSZ-HJ25VA

INDOOR UNIT WALL

MICROPHONE

0.8m

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

COOLING

FUNCTION SPL(dB(A)) LINE

Super High

FAN SPEED

HEATING

Test conditions

Cooling : Dry-bulb temperature 27°C Wet-bulb temperature 19°C

Heating : Dry-bulb temperature 20°C

NC-10

MSZ-HJ35VA

4NOISE CRITERIA CURVES

MSZ-HJ50VA

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

COOLING

FUNCTION SPL(dB(A)) LINE

Super High

FAN SPEED

HEATING

NC-10

OBH647A

MSZ-HJ25VA MSZ-HJ35VA MSZ-HJ50VA Unit : mm

MSZ-HJ25VA MSZ-HJ35VA MSZ-HJ50VA

5OUTLINES AND DIMENSIONS

6WIRING DIAGRAM

2325

799

785 7

290

12063049

103

130

100

(57°)

225 225 80.5

80.5

61.5

59.5340338

249

248 21.5

167 157

207.5

206.5

172

140

57 18

Air in

Installation plate

Piping

Drain hose

Air out

11×26 Oblong hole 11×20 Oblong hole

Installation plate

Indoor unit

Wall hole Φ65

In case of left,

left back,or

left under piping

(using spacer),

108.5 or more

7 or more

33.5 or more

40 or more

20 or more

Piping

Insulation Φ35 O.D

Liquid line Φ6.35 - 0.39m (Flared connection Φ6.35)

Gas line Φ9.52 - 0.34m (Flared connection Φ9.52)

Drain hose

InslationΦ28 Connected part Φ16 O.D active length 370

MSZ-HJ25/35VA

MSZ-HJ50VA

Piping

Insulation Φ37 O.D

Liquid line Φ6.35 - 0.39m (Flared connection Φ6.35)

Gas line Φ9.52 - 0.34m (Flared connection Φ12.7)

Drain hose

InslationΦ28 Connected part Φ16 O.D active length 370

OBH647A

MSZ-HJ25VA MSZ-HJ35VA

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Flared connection

Refrigerant flow in cooling

Refrigerant flow in heating

Refrigerant pipe ø9.52

(with heat insulator)

Refrigerant pipe ø6.35

(with heat insulator)

Indoor coil

thermistor

RT12

Indoor coil

thermistor

RT13

Unit : mm

MSZ-HJ50VA

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Flared connection

Refrigerant flow in cooling

Refrigerant flow in heating

Refrigerant pipe ø12.7

(with heat insulator)

Refrigerant pipe ø6.35

(with heat insulator)

Indoor coil

thermistor

RT12

Indoor coil

thermistor

RT13

7REFRIGERANT SYSTEM DIAGRAM

OBH647A

8-2. P.C. BOARD MODIFICATION FOR INDIVIDUAL OPERATION

A maximum of 4 indoor units with wireless remote controllers can be used in a room.

In this case, to operate each indoor unit individually by each remote controller, P.C. boards of remote controller must be

modified according to the number of the indoor unit.

8-1. TIMER SHORT MODE

For service, the following set time can be shortened by short circuiting the timer short mode point on the electronic control

P.C. board. (Refer to 10-7.)

Set time : 3-minute →3-second (It takes 3 minutes for the compressor to start operation. However, the starting time is

shortened by short circuiting the timer short mode point.)

Table 1 1 unit operation 2 units operation 3 units operation 4 units operation

No. 1 unit No modiﬁcation Same as at left Same as at left Same as at left

No. 2 unit – Solder J1 Same as at left Same as at left

No. 3 unit – – Solder J2 Same as at left

No. 4 unit – – – Solder both J1 and J2

How to set the remote controller exclusively for particular indoor unit

After you turn the breaker ON, the first remote controller that sends the signal to the indoor unit will be regarded as the remote

controller for the indoor unit.

The indoor unit will only accept the signal from the remote controller that has been assigned to the indoor unit once they are

set.

The setting will be cancelled if the breaker has turned OFF, or the power supply has shut down.

Please conduct the above setting once again after the power has restored.

How to modify the remote controller P.C. board

Remove batteries before modification.

The board has a print as shown below :

The P.C. board has the print “J1” and “J2”. Solder “J1” and “J2” according to the number of indoor unit as shown in Table 1.

After modification, press the RESET button.

NOTE : For modification, take out

the batteries and press

the OPERATE/STOP (ON/

OFF) button 2 or 3 times at

first.

After finish modification,

put back the batteries then

press the RESET button.

MSZ-HJ25VA MSZ-HJ35VA MSZ-HJ50VA

8SERVICE FUNCTIONS

OBH647A

NOTE:

• The operation settings are memorized when 10 seconds have passed after the indoor unit was operated with the

remote controller.

• If main power is turned OFF or a power failure occurs while AUTO START/STOP timer is active, the timer setting is

cancelled.

• If the unit has been off with the remote controller before power failure, the auto restart function does not work as the

power button of the remote controller is off.

• To prevent breaker OFF due to the rush of starting current, systematize other home appliance not to turn ON at the

same time.

• When some air conditioners are connected to the same supply system, if they are operated before power failure, the

starting current of all the compressors may flow simultaneously at restart.

Therefore, the special counter measures are required to prevent the main voltage-drop or the rush of the starting

current by adding to the system that allows the units to start one by one.

JR77

Indoor electronic

control P.C. board

CN10ACN111

CN151

CN112

CN110

8-3. AUTO RESTART FUNCTION

When the indoor unit is controlled with the remote controller, the operation mode, the set temperature, and the fan speed

are memorized by the indoor electronic control P.C. board. “AUTO RESTART FUNCTION” automatically starts operation

in the same mode just before the shutoff of the main power.

Operation

If the main power has been cut, the operation settings remain.

After the power is restored, the unit restarts automatically according to the memory.

(However, it takes at least 3 minutes for the compressor to start running.)

How to disable “AUTO RESTART FUNCTION”

Turn off the main power for the unit.

Cut the Jumper wire to JR77 on the indoor electronic control P.C. board. (Refer to 10-7.)

OBH647A

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric MS-GF50VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PEFV-P72NMHSU-E Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric PLA-RP35BA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-LN18VG2W-SC1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSH-XV07UV Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. Slim MSZ-GE06NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SUZ-SWM40VA Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric MFZ-KJ25VE Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. SLIM SLZ-M FA Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MXZ-6F120VGD Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr Slim PLA-RP-AA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. SLIM PU-2NJA Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric MSZ-GL18NA-U2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-HJ25VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric M-SERIES Manual de usuario

Mitsubishi Electric

Mitsubishi Electric BRANCH BOX PAC-MKA52BC Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PK12FK3 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-GL06NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-AP20VF Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-D30NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MXZ-2B30VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-FE09/12NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PLFY Series Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric PUHZ-P200YHA Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario