Mitsubishi Electric MSZ-GA22VA-E1 Manual de usuario

SERVICE MANUAL

CONTENTS

1. TECHNICAL CHANGES ····································2

2. PART NAMES AND FUNCTIONS······················3

3. SPECIFICATION·················································5

4. NOISE CRITERIA CURVES·······························6

5. OUTLINES AND DIMENSIONS ·························7

6. WIRING DIAGRAM ············································8

7. REFRIGERANT SYSTEM DIAGRAM················8

8. SERVICE FUNCTIONS ······································9

9. TROUBLESHOOTING······································10

10. DISASSEMBLY INSTRUCTIONS·····················24

11. PARTS LIST······················································27

12. OPTIONAL PARTS···········································30

Wireless type

Models

MSZ-GA22VA - (WH)

MSZ-GA25VA - (WH)

MSZ-GA35VA - (WH)

No. OB378

SPLIT-TYPE, HEAT PUMPAIR CONDITIONERS

Indication of model name

MSZ-GA22VA -

MSZ-GA25VA -

MSZ-GA35VA - E1

NOTE:

This service manual describes technical data of the indoor units.

•As for outdoor units MUZ-GA25VA- , MUZ-GA35VA- , MUZ-GA25VAH-

and MUZ-GA35VAH- , refer to service manual OB379.

•As for outdoor units MXZ-3A54VA- , MXZ-4A71VA- and MXZ-4A80VA- ,

refer to service manual OB377. E1E1E1

E1E1E1

OB378_--1qxp 05.1.17 12:55 Page 1

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

1TECHNICAL CHANGES

MSZ-A09YV - ➔MSZ-GA22VA -

MSZ-A09YV - ➔MSZ-GA25VA -

MSZ-A12YV - ➔MSZ-GA35VA - E1E1

E1E1

1. Indication of capacity has been changed.(BTU base ➔kW base)

2. Control method between indoor and outdoor has been changed.

3. Power supply method has been changed (change to supply from outdoor unit).

4. Power supply cord has been removed.

5. Indoor electronic control P.C. board has been changed.

6. Position of terminal block has been changed.

7. Indoor fan motor has been changed. ( AC ➔DC)

8. Indoor heat exchanger has been changed.

9. The horizontal vane motor unit has been changed.

An external gear is added to the generalized stepping motor.

The unit is structured so that the driving torque and stopping torque would increase.

NOTE:Do not remove the vane motor from the motor unit.

Do not disassemble the horizontal vane motor unit.

Generalized stepping motor

10. Air cleaning filer has been removed (available as an optional part).

11. Signal of remote controller has been changed. ( It is not available for the conventional models.)

12. Symbol on terminal block has been changed (to S1/S2/S3).

OB378_--1qxp 05.1.17 12:55 Page 2

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

PART NAMES AND FUNCTIONS

INDOOR UNIT

MSZ-GA22VA -

MSZ-GA25VA -

MSZ-GA35VA - E1

Line flow fan

Air outlet

Vertical vane

Air inlet

Display section

Front panel

Panel

Heat exchanger

Horizontal vane

Operation section

(When the front panel is opened)

Remote controller

Remote control

receiving section

Catechin air filter

Air cleaning filter

(Optional parts,Anti-

Allergy Enzyme Filter,

Blue bellows type)

Emergency operation switch

Fan guard

Operation Indicator

lamp

OB378_--1qxp 05.1.17 12:55 Page 3

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

ACCESSORIES

Installation plate

Installation plate fixing screw 4 o25 mm

Remote controller holder

Fixing screw for 33.5 o1.6 mm (Black)

Battery (AAA) for remote controller

Wireless remote controller

Felt tape (Used for left or left-rear piping)

MSZ-GA22VA - E1

MSZ-GA25VA - E1

MSZ-GA35VA - E1

INDOOR UNIT

ON-TIMER button

CLOCK SET button

TIME SET buttons

FORWARD button

BACKWARD button

OFF-TIMER button

(This diagram shows an overall view.)

Open the front lid.

RESET button VANE CONTROL button

Signal transmitting section

Operation display section

Temperature buttons

OPERATE/STOP

(ON/OFF) button

FAN SPEED CONTROL button

OPERATION SELECT button

ECONO COOL button

Indication of

remote controller

model is on back

MSZ-GA22VA -

MSZ-GA25VA -

MSZ-GA35VA - E1

OB378_--1qxp 05.1.17 12:55 Page 4

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

SPECIFICATION

T3.15AL 250V

MSBPC20M16 12V DC 250"(at 25˚C)

ERZV14D471

INDOOR UNIT

Item Model

Fuse

Horizontal vane motor

Varistor

Terminal block

MSZ-GA22VA - E1 MSZ-GA25VA - E1 MSZ-GA35VA - E1

(F11)

(MV)

(NR11)

(TB)

Specifications and rating conditions of main electric parts

MSZ-GA25VA - E1

MSZ-GA22VA - E1 MSZ-GA35VA - E1

Indoor model

Function

Power supply Single phase

230V,50Hz

0.25

—

0.25

RC0J30-CC

780O298O210

36W/29W/21W

KM05B

Single phase

230V,50Hz

0.25

—

0.25

RC0J30-CC

780O298O210

36W/29W/21W

KM05B

540

36W/29W/21W

1,100

36W/29W/22W

Cooling

600

480W/366W/234W

1,200

1,000W/800W/580W

Heating

630

504W/384W/258W

1,250

1,040W/830W/620W

Cooling

600

480W/366W/234W

1,200

1,000W/800W/580W

Heating

630

504W/384W/258W

1,250

1,040W/830W/620W

Single phase

230V,50Hz

0.25

—

0.25

RC0J30-CC

780O298O210

36W/29W/22W

KM05B

Cooling

600

480W/366W/246W

1,200

1,000W/800W/600W

Heating

630

504W/384W/270W

1,250

1,040W/830W/640W

Air flow(Super High)

Air flow(HighW/Med.W/LowW)

Power outlet

Running current ✽1

Power input ✽1

Auxiliary heater

Power factor ✽1

Fan motor current ✽1

Model

Dimensions WOHOD

Weight

Air direction

Sound level(Super High)

Sound level(HighW/Med.W/LowW)

Fan speed(Super High)

Fan speed(HighW/Med.W/LowW)

Fan speed regulator

Thermistor RT11(at25:)

Thermistor RT12(at25:)

Thermistor RT13(at25:)

Remote controller model

K/h

A(kW)

dB(A)

rpm

Electrical

data

Fan motor

Special

remarks

Capacity

MSZ-GA25VA - E1

MSZ-GA22VA - E1 MSZ-GA35VA - E1

Indoor model

Function Cooling

438W/342W/240W

930W/760W/580W

Heating

420W/366W/258W

900W/800W/620W

Cooling

438W/342W/240W

930W/760W/580W

Heating

420W/366W/258W

900W/800W/620W

Cooling

600

480W/366W/246W

1,200

1,000W/800W/600W

Heating

618

504W/390W/270W

1,230

1,040W/850W/640W

Air flow(Super High)

Air flow(HighW/Med.W/LowW)

Sound level(Super High)

Sound level(HighW/Med.W/LowW)

Fan speed(Super High)

Fan speed(HighW/Med.W/LowW)

K/h

dB(A)

rpm

Special

remarks

Capacity

540

36W/29W/21W

1,100

NOTE : Test conditions are based on ISO 5151

Cooling : Indoor Dry-bulb temperature 27:Wet-bulb temperature 19:

Outdoor Dry-bulb temperature 35:Wet-bulb temperature 24:

Heating : Indoor Dry-bulb temperature 20:Wet-bulb temperature 15:

Outdoor Dry-bulb temperature 7:Wet-bulb temperature 6:

Refrigerant piping length (one way): 5m

wReference value

✽1 Measured under rated operating frequency.

When outdoor unit is MXZ type.

OB378_--1qxp 05.1.17 12:55 Page 5

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

4NOISE CRITERIA CURVES

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

Test conditions,

Cooling : Dry-bulb temperature 27: Wet-bulb temperature 19:

APPROXIMATE

THRESHOLD OF

HEARING FOR

CONTINUOUS

NOISE

COOLING

FUNCTION

SPL(dB(A)) LINE

Super High

FAN SPEED

HEATING

Heating : Dry-bulb temperature 20: Wet-bulb temperature 15:

MSZ-GA22VA -

MSZ-GA25VA - E1

INDOORUNIT WALL

MICROPHONE

0.8m

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

BAND CENTER FREQUENCIES, Hz

Test conditions,

Cooling : Dry-bulb temperature 27: Wet-bulb temperature 19:

APPROXIMATE

THRESHOLD OF

HEARING FOR

CONTINUOUS

NOISE

COOLING

FUNCTION

SPL(dB(A)) LINE

Super High

FAN SPEED

HEATING

Heating : Dry-bulb temperature 20: Wet-bulb temperature 15:

MSZ-GA35VA - E1

OB378_--1qxp 05.1.17 12:55 Page 6

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

OUTLINES AND DIMENSIONS

MSZ-GA25VA - E1

Unit : mm

INDOOR UNIT

155 155

335 320

41.5 215

42.5 214

3287.5

7055

5555 225 225

or more7

100

106

298

102624.5

780

210 5

53.5

159

14273.5

234

Air in

Air out

Wall hole [65

Indoor unit

Installation plate

11X20 Oblong hole

11X26 Oblong hole

10 or more

75 or more

66 or more

75 or more

In case of left, left back, or

left under piping (using spacer),

115 or more

Insulation [28

Drain hose [16

(Connected part O.D)

Liquid line [6.35-0.5m

Gas line [9.52-0.43m

Insulation [35 O.D

[19 I.D

{

Required space (Indoor unit)

MSZ-GA35VA - E1

MSZ-GA22VA - E1

OB378_--1qxp 05.1.17 12:55 Page 7

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

6WIRING DIAGRAM

REFRIGERANT SYSTEM DIAGRAM

MSZ-GA22VA -

MSZ-GA25VA -

MSZ-GA35VA - E1

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Indoor coil

thermistor

RT13(sub)

Flared connection

Refrigerant flow in cooling

Refrigerant flow in heating

Refrigerant pipe [9.52

(with heat insulator)

Refrigerant pipe [6.35

(with heat insulator)

Indoor coil

thermistor

RT12(main)

INDOOR UNIT

Unit : mm

INDOOR UNIT MODELS WIRING DIAGRAM

SYMBOL

DB111

F11

NR11

SYMBOL

RT11

RT12

RT13

T111

NAME

DIODE STACK

FUSE (T3.15AL250V)

INDOOR FAN MOTOR

VANE MOTOR (HORIZONTAL)

VARISTOR

NAME

ROOM TEMPERATURE THERMISTOR

INDOOR COIL THERMISTOR (MAIN)

INDOOR COIL THERMISTOR (SUB)

TRANSFORMER

TERMINAL BLOCK

NOTE:1. About the outdoor side electric wiring refer to the outdoor unit electric wiring diagram for servicing.

2. Use copper conductors only. (For field wiring)

3. Symbols below indicate.

/: Terminal block, : Connector

MSZ-GA22VA -

MSZ-GA25VA -

MSZ-GA35VA - E1

POWER MONITOR

RECEIVER P.C.BOARD

230V~

BLU

INDOOR ELECTRONIC

CONTROL P.C. BOARD

SW P.C.

BOARD

INTERLOCK

SWITCH(FAN)

TO OUTDOOR

UNIT

CONNECTING

BLK

RED

TB TAB3

DB111

NR11

F11

105(T)

101(A)

12-24V

RT13

1R1

GRN

LD104

CN201

151

T111

RED

WHT

111

112

CN211 BLU

YLW

BLK

RT11

RT12

OB378_--1qxp 05.1.17 12:55 Page 8

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

SERVICE FUNCTIONS

8-2. P.C. BOARD MODIFICATION FOR INDIVIDUAL OPERATION

A maximum of 4 indoor units with wireless remote controllers can be used in a room.

In this case, to operate each indoor unit individually by each remote controller, P.C. boards of remote controller must be

modified according to the number of the indoor unit.

8-1. TIMER SHORT MODE

For service, set time can be shortened by short circuit of JPG and JPS the electronic control P.C. board.

The time will be shortened as follows. (Refer to 9-7.)

Set time : 1-minute ➔ 1-second

Set time : 3-minute ➔ 3-second (It takes 3 minutes for the compressor to start operation. However, the starting time is

shortened by short circuit of JPG and JPS.)

No. 1 unit

No. 2 unit

No. 3 unit

No. 4 unit

1 unit operation

No modification

–

2 units operation

Same as at left

Solder J1

–

3 units operation

Same as at left

Solder J2

–

4 units operation

Same as at left

Solder both J1 and J2

Table 1

How to set the remote controller exclusively for particular indoor unit.

After you turn the breaker ON, the first remote controller that sends the signal to the indoor unit will be regarded as the remote

controller for the indoor unit.

The indoor unit will only accept the signal from the remote controller that has been assigned to the indoor unit once they are

set.

The setting will be cancelled if the breaker has turned off, or the power supply has shut down.

Please conduct the above setting once again after the power has restored.

How to modify the remote controller P.C. board

Remove batteries before modification.

The board has a print as shown below :

The P.C. board has the print “J1” and “J2”. Solder “J1” and “J2” according to the number of indoor unit as shown in Table 1.

After modification, press the RESET button.

NOTE : For remodelling, take out

the batteries and press the

OPERATE/STOP(ON/OFF)

button twice or 3 times at

first.

After finish remodelling,

put back the batteries then

press the RESET button.

Remote controller model : KM05B

MSZ-GA22VA -

MSZ-GA25VA -

MSZ-GA35VA - E1

OB378_--1qxp 05.1.17 12:55 Page 9

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

TROUBLESHOOTING

9-1. Cautions on troubleshooting

1. Before troubleshooting, check the following:

1) Check the power supply voltage.

2) Check the indoor/outdoor connecting wire for mis-wiring.

2. Take care the following during servicing.

1) Before servicing the air conditioner, be sure to turn off the unit first with the remote controller, and then after

confirming the horizontal vane is closed, turn off the breaker and / or disconnect the power plug.

2) Be sure to turn OFF the power supply before removing the front panel, the cabinet, the top panel, and the

electronic control P.C. board.

3) When removing the electronic control P.C. board, hold the edge of the board with care NOT to apply stress on the

components.

4) When connecting or disconnecting the connectors, hold the housing of the connector. DO NOT pull the lead wires.

Housing point

Lead wiring

MSZ-GA22VA - MSZ-GA25VA - MSZ-GA35VA - E1E1E1

NOTE:

• The operation settings are memorized when 10 seconds have passed after the indoor unit was operated with the

remote controller.

• If main power is turned OFF or a power failure occurs while AUTO START/STOP timer is active, the timer setting is

cancelled.

• If the unit has been off with the remote controller before power failure, the auto restart function does not work as the

power button of the remote controller is off.

• To prevent breaker off due to the rush of starting current, systematize other home appliance not to turn on at the

same time.

• When some air conditioners are connected to the same supply system, if they are operated before power failure,

the starting current of all the compressors may flow simultaneously at restart.

Therefore, the special counter-measures are required to prevent the main voltage-drop or the rush of the starting

current by adding to the system that allows the units to start one by one.

JR07

CN151 CN211CN112 CN1R1

8-3. AUTO RESTART FUNCTION

When the indoor unit is controlled with the remote controller, the operation mode, the set temperature, and the fan speed

are memorized by the indoor electronic control P.C. board. The “AUTO RESTART FUNCTION” sets to work the moment

power has restored after power failure. Then, the unit will restart automatically.

Operation

1If the main power has been cut, the operation settings remain.

2After the power is restored, the unit restarts automatically according to the memory.

(However, it takes at least 3 minutes for the compressor to start running.)

How to release “AUTO RESTART FUNCTION”

1Turn off the main power for the unit.

2Solder the Jumper wire to JR07 on the indoor electronic control P.C. board. (Refer to 9-7.)

OB378_--1qxp 05.1.17 12:55 Page 10

Mitsubishi ilmalämpöpumput huoltaa ja korjaa Jäähdytinpalvelu RefGroup Oy

www.ilmalämpöpumput.com

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PEFY-P-VMA3-E Guía del producto

Mitsubishi Electric

Mitsubishi Electric PUHZ-P200YKA3 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PMFY Series Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PKFY-P VLM Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-HE09NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PKFY-P NAMU-E Manual de instalación y operación

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PFFY-P20VCM-E Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric MU-A09WA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUHY-RP200 Cómo utilizar

Mitsubishi Electric

Mitsubishi Electric MUZ-EF25VE-E1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MCFH-A24WV Manual de usuario

Mitsubishi Electric

Mitsubishi Electric City Multi PUMY-SP112VKM Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.SLIM PSA-RP-KA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.Slim SUZ-KA25VA3 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.SLIM PCA-M140KA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MXZ-8A140VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-CA25VB Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MLZ-KA25VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUHZ-P200YHA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-EF18VGW Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-GE22VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUZ-A NHA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI P500YMF-C Cómo utilizar

Mitsubishi Electric

Mitsubishi Electric CITY MULTI CMY-Q100VBK Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario