Mitsubishi Electric Mr.Slim SUZ-KA25VA3 Manual de usuario

TECHNICAL & SERVICE MANUAL

No.OCH530

REVISED EDITION-A

SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS

R410A

Outdoor unit

[Model Name]

[Service Ref.]

SUZ-KA25VA3 SUZ-KA25VA3.TH

SUZ-KA35VA3 SUZ-KA35VA3.TH

SUZ-KA50VA3 SUZ-KA50VA3.TH

SUZ-KA60VA3 SUZ-KA60VA3.TH

SUZ-KA71VA3 SUZ-KA71VA3.TH

CONTENTS

COMBINATION OF INDOOR AND OUTDOOR UNITS

..... 2

2. TECHNICAL CHANGES ................................... 3

3. PARTS NAMES AND FUNCTIONS .................. 7

4. SPECIFICATION................................................ 8

5. NOISE CRITERIA CURVES............................ 10

6. OUTLINES AND DIMENSIONS .......................11

7. WIRING DIAGRAM.......................................... 13

8. REFRIGERANT SYSTEM DIAGRAM............. 16

9. ACTUATOR CONTROL................................... 19

10. SERVICE FUNCTIONS.................................... 20

11. TROUBLESHOOTING..................................... 20

12. DISASSEMBLY INSTRUCTIONS.................... 36

Indication of

model name

HFC

utilized

R410A

SUZ-KA25VA3.TH

SUZ-KA35VA3.TH

September 2013

PARTS CATALOG (OCB530)

Note:

• This service manual

describes technical data of

the outdoor units.

Revision:

• Errors have been corrected

in REVISED EDITION-A.

• Some descriptions have

been modified.

• Please void OCH530.

1COMBINATION OF INDOOR AND OUTDOOR UNITS

Heat pump type

Outdoor unit

SUZ-

SLZ-KA25VA(L).TH

SLZ-KA35VA(L).TH

SLZ-KA50VA(L).TH

SLZ-KA25VAL2.TH

SLZ-KA35VALR3.TH

SLZ-KA50VALR3.TH

SLZ-KA25VAQ2.TH

SLZ-KA35VAQR2.TH

SLZ-KA50VAQR2.TH

SEZ-KD25VA(L)R2.TH

SEZ-KD35VA(L)R2.TH

SEZ-KD50VA(L)R2.TH

SEZ-KD60VA(L)R2.TH

SEZ-KD71VA(L)R2.TH

SEZ-KD25VAQR2.TH

SEZ-KD35VAQR2.TH

SEZ-KD50VAQR2.TH

SEZ-KD60VAQR2.TH

SEZ-KD71VAQR2.TH

—

OC320

OCH493

Indoor unit

Service

Manual No.

Service Ref.

Heat pump without electric heater

KA25VA3.TH

KA60VA3.TH KA71VA3.THKA50VA3.TH

HWE0711

BWE102050

BWE102040

HWE1008

KA35VA3.TH

(NOTE) Please refer to the service manual of indoor unit or the technical data book for the combination data.

INDOOR UNIT SERVICE MANUAL

OCH530A

2TECHNICAL CHANGES

Refrigerant

oil

Refrigerant

New refrigerant

R410A

HFC-32: HFC-125 (50%:50%)

Pseudo-azeotropic refrigerant

Not included

A1/A1

72.6

-51.4

1.557

Non combustible

1730

From liquid phase in cylinder

Possible

Incompatible oil

None

Previous refrigerant

R22

R22 (100%)

Single refrigerant

Included

86.5

-40.8

0.94

44.4

Non combustible

0.055

1700

Gas phase

Possible

Compatible oil

Light yellow

None

Refrigerant

Composition (Ratio)

Refrigerant handling

Chlorine

Safety group (ASHRAE)

Molecular weight

Boiling point (°C)

Steam pressure [25°C](Mpa)

Saturated steam density [25°C](Kg/K)

Combustibility

ODP *1

GWP *2

Refrigerant charge method

Additional charge on leakage

Kind

Color

Smell

*1: Ozone Depletion Potential : based on CFC-11

*2: Global Warming Potential : based on CO2

INFORMATION FOR THE AIR CONDITIONER WITH R410A REFRIGERANT

• This room air conditioner adopts an HFC refrigerant (R410A) which never destroys the ozone layer.

• Pay particular attention to the following points, though the basic installation procedure is same as that for R22 conditioners.

As R410A has working pressure approximate 1.6 times as high as that of R22, some special tools and piping parts/materi-

als are required. Refer to the table below.

Take sufficient care not to allow water and other contaminations to enter the R410A refrigerant during storage and installa-

tion, since it is more susceptible to contaminations than R22.

For refrigerant piping, use clean, pressure-proof parts/materials specifically designed for R410A. (Refer to 2. Refrigerant

piping.)

Composition change may occur in R410A since it is a mixed refrigerant. When charging, charge liquid refrigerant to prevent

composition change.

NOTE : The unit of pressure has been changed to MPa on the international system of units (SI unit system).

The conversion factor is: 1 (MPa [Gauge]) =10.2 (kgf/cm2[Gauge])

New Specification Current Specification

The incompatible refrigerant oil easily separates from

refrigerant and is in the upper layer inside the suction muffler.

Raising position of the oil back hole enables to back the

refrigerant oil of the upper layer to flow back to the

compressor.

Since refrigerant and refrigerant oil are compatible with

each other, refrigerant oil backs to the compressor through

the lower position oil back hole.

Compressor

Suction muffler

Oil back hole

Refrigerant oil

Refrigerant

Compressor

Suction muffler

Oil back hole

Refrigerant oil /Refrigerant

Compressor

OCH530A

R410A tools Can R22 tools be used?

Gas leak detector

R410A has high pressures beyond the measurement range of existing

gauges. Port diameters have been changed to prevent any other refrigerant

from being charged into the unit.

Hose material and cap size have been changed to improve the pressure

resistance.

Dedicated for HFC refrigerant.

6.35 mm and 9.52 mm

Description

Clamp bar hole has been enlarged to reinforce the spring strength in the tool.

Provided for flaring work (to be used with R22 flare tool).

Provided to prevent the back flow of oil. This adapter enables you to use

vacuum pumps.

It is difficult to measure R410Awith a charging cylinder because the

refrigerant bubbles due to high pressure and high-speed vaporization

Yes

New

Gauge manifold

Charge hose

Torque wrench

Flare tool

Flare gauge

Vacuum pump

adapter

Electronic scale for

refrigerant charging

No: Not substitutable for R410A Yes: Substitutable for R410A

No 12.7 mm and 15.88 mm

1. Tools dedicated for the air conditioner with R410A refrigerant

The following tools are required for R410A refrigerant. Some R22 tools can be substituted for R410A tools.

The diameter of the service port on the stop valve in outdoor unit has been changed to prevent any other refrigerant being

charged into the unit. Cap size has been changed from 7/16 UNF with 20 threads to 1/2 UNF with 20 threads.

-30 -20 -10 0 10 20 30 40 50 60

-0.5

0.0

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

(MPa [Gauge])

R410A

R22

Conversion chart of refrigerant temperature and pressure

Saturated liquid pressure

(:)

NOTE: The unit of pressure has been changed to MPa on the

international system of units (SI unit system).

The conversion factor is: 1 (MPa [Gauge]) =10.2 (kgf/cm2[Gauge])

OCH530A

Electronic scale for refrigerant charging

Outdoor unit

Refrigerant gas

cylinder

operating valve

Refrigerant gas cylinder

for R410A with siphon

Refrigerant (liquid)

Service port

Gauge manifold

valve (for R410A)

Union

Liquid pipe

Gas pipe

Stop valve

Indoor unit

Charge hose (for R410A)

R410A

Pipe diameter (mm)

6.35

9.52

12.7

15.88

Dimension of flare nut (mm)

R22

• Use a copper pipe or a copper-alloy seamless pipe with a thickness of 0.8 mm. Never use any pipe with a thickness less

than 0.8mm, as the pressure resistance is insufficient.

Flaring work and flare nut

Flaring work for R410A pipe differs from that for R22 pipe.

For details of flaring work, refer to Installation manual “FLARING WORK”.

3. Refrigerant oil

Apply the special refrigerant oil (accessories: packed with indoor unit) to the flare and the union seat surfaces.

4. Air purge

Do not discharge the refrigerant into the atmosphere.

Take care not to discharge refrigerant into the atmosphere during installation, reinstallation, or repairs to the refrigerant

circuit.

Use the vacuum pump for air purging for the purpose of environmental protection.

5. Additional charge

For additional charging, charge the refrigerant from liquid phase of the gas cylinder.

If the refrigerant is charged from the gas phase, composition change may occur in the refrigerant inside the cylinder and

the outdoor unit. In this case, ability of the refrigerating cycle decreases or normal operation can be impossible. However,

charging the liquid refrigerant all at once may cause the compressor to be locked. Thus, charge the refrigerant slowly.

2. Refrigerant piping

Specifications

Use the refrigerant pipes that meet the following specifications.

Wall thicknessOutside diameter

Pipe mm mm

For liquid

For gas

6.35

9.52

12.7

15.88

0.8

1.0

Heat resisting foam plastic

Specific gravity 0.045

Thickness 8 mm

Insulation material

OCH530A

6. Pumping Down

When relocating or disposing of the air conditioner, pump down the system by following the procedure below so that no

refrigerant is released into the atmosphere.

1 Turn off the power supply (circuit breaker).

2 Connect the gauge manifold valve to the service port of the stop valve on the gas pipe side of the outdoor unit.

3 Fully close the stop valve on the liquid pipe side of the outdoor unit.

4 Supply power (circuit breaker).

5 Perform the refrigerant collecting operation (cooling test run).

• For the PAR-31MAA, select “Service” → “TestRun” from the main menu to start the test run, and then select the cooling

mode.

• For details or for other information about starting the test run when using remote controllers, refer to the installation manual

for the indoor unit or the remote controller.

6 Fully close the stop valve on the gas pipe side of the outdoor unit when the pressure gauge shows 0.05 to 0 MPa [Gauge]

(approx. 0.5 to 0 kgf/cm²) and quickly stop the air conditioner.

• Push the “ON/OFF” button on the remote controller to stop the air conditioner.

Note:

When the extension piping is very long with a large refrigerant amount, it may not be possible to perform a pump down

operation. In this case, use refrigerant recovery equipment to collect all of the refrigerant in the system.

7 Turn off the power supply (circuit breaker), remove the gauge manifold valve, and then disconnect the refrigerant pipes.

.Warning: When pumping down the refrigerant, stop the compressor before disconnecting the refrigerant pipes.

• If the refrigerant pipes are disconnected while the compressor is operating and the stop valve (ball valve) is open,

the pressure in the refrigeration cycle could become extremely high if air is drawn in, causing the pipes to burst,

personal injury, etc.

OCH530A

3PARTS NAMES AND FUNCTIONS

SUZ-KA25VA3.TH

SUZ-KA35VA3.TH

SUZ-KA50VA3.TH

SUZ-KA60VA3.TH

SUZ-KA71VA3.TH

Air outlet

Drain outlet

Piping

Drain hose

Air inlet

(back and side)

Model SUZ-KA·VA3.TH

Drain socket 1

Piping

Air outlet

Drain outlet

Air inlet

(back and side)

Drain hose

Piping

Air outlet

Drain outlet

Air inlet

(back and side)

Drain hose

OCH530A

SPECIFICATION

NOTE : Test conditions are based on ISO 5151

Cooling : Indoor D.B. 27°C W.B. 19°C

Outdoor D.B. 35°C

Heating : Indoor D.B. 20°C

Outdoor D.B. 7°C W.B. 6°C

Refrigerant piping length (one way): 5 m

*1 Measured under rated operating frequency.

Outdoor model

SUZ-KA25VA3.TH SUZ-KA35VA3.TH SUZ-KA50VA3.TH SUZ-KA60VA3.TH SUZ-KA71VA3.TH

Power supply Single phase 230V, 50Hz

Compressor

Model KNB073FKFMC KNB092FFAMC SNB130FGBMT SNB172FEKMT

Output W 550 650 900 1,200

Current

Cooling A2.76 4.06 5.58 6.62 8.02

Heating 3.24 4.09 5.75 6.37 8.13

Refrigeration oil

(Model)

L0.31 (FV50S) 0.27 (FV50S) 0.35 (FV50S) 0.4 (FV50S)

Fan motor

Model RC0J50-FA RC0J60-BD RC0J60-BC

Current

Cooling A0.24 0.29 0.84 0.84 0.83

Heating 0.27 0.28 0.93 0.93 0.82

Dimensions W × H × D mm 800 × 550 × 285 840 × 880 × 330

Weight kg 30 35 54 50 53

Special remarks

Air ow

Cooling

High

m³/h

1,806 2,868 3,492 3,426

Med. 1,806 2,868 3,066 3,006

Low 1,170 1,038 1,602 1,692 1,512

Heating

High 2,106 2,778 2,952 2,892

Med. 1,806 1,770 2,778 2,952 2,892

Low 1,452 1,326 2,124 2,226 2,280

Sound level *1 Cooling

dB(A)

47 49 52 55

Heating 48 50 52 55

Fan

speed

Cooling

High

rpm

740 810 840 950

Med. 740 810 840

Low 740 490 480 450

Heating

High 860 900 810

Med. 740 770 810

Low 600 610 620 650

Fan speed regulator 3

Refrigerant lling capacity

(R410A) kg 0.80 1.15 1.60 1.80 1.80

OCH530A

SUZ-KA25VA3.TH SUZ-KA35VA3.TH

SUZ-KA50VA3.TH SUZ-KA60VA3.TH

SUZ-KA71VA3.TH

Specifications and rating conditions of main electric parts

Model

Item

SUZ-KA25VA3.TH SUZKA35VA3.TH SUZ-KA50VA3.TH SUZ-KA60VA3.TH SUZ-KA71VA3.TH

Smoothing

capacitor

(C61) — — 620+ 420V — —

(C62, C63) 620+ 420V 620+ 420V 620+ 420V — —

(CB1, 2, 3) ———560μF 450V 560μF 350V

Diode module (DB61) 15A 600V 15A 600V 25A 600V — —

Fuse

(F61) T20A L250V T20A L250V T20A L250V — —

(F62) ———T20A L250V T20A L250V

(F701, F801, F901)

T3.15A L250V T3.15A L250V T3.15A L250V — —

(IC700) 15A 600V 15A 600V 20A 600V — —

Inteligent power

module

(IPM) — — — 20A 600V

(IC932) 8A 600V 8A 600V 8A 600V 5A 600V 5A 600V

Power factor

controller

(PFC) ———20A 600V 20A 600V

(IC820) 20A 600V 20A 600V 20A 600V — —

Expansion valve

coil (LEV) DC12V

Reactor (L61) 18mH 23mH 23mH — —

(L) — — — 340μH 20A 340μH 20A

Current-Limiting

PTC thermistor (PTC64, PTC65) 33Ω

Terminal block (TB1, TB2) ———3P 3P

(TB) 5P 5P 5P — —

Relay

(X63) 3A 250V 3A 250V 3A 250V — —

(X64) 20A 250V

(X601) ———3A 250V 3A 250V

(X602) ———3A 250V 3A 250V

R.V. coil (21S4) AC220-240V

OCH530A

NOISE CRITERIA CURVES

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

COOLING

FUNCTION SPL(dB(A)) LINE

High

Med.

FAN SPEED

HEATING

OUTDOORUNIT

MICROPHONE

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

BAND CENTER FREQUENCIES, Hz

NC-10

SUZ-KA25VA3.TH

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

COOLING

FUNCTION SPL(dB(A)) LINE

FAN SPEED

HEATING

OUTDOORUNIT

MICROPHONE

High

Med.

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

BAND CENTER FREQUENCIES, Hz

NC-10

SUZ-KA35VA3.TH

COOLING

FUNCTION SPL(dB(A)) LINE

High

FAN SPEED

HEATING

OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

BAND CENTER FREQUENCIES, Hz

NC-10

SUZ-KA50VA3.TH

Test conditions

Cooling: Dry-bulb temperature 35°C

Heating: Dry-bulb temperature 7°C

Wet-bulb temperature 6°C

OUTDOOR UNIT

MICROPHONE

1 m

SUZ-KA60VA3.TH SUZ-KA71VA3.TH

OCTAVE BAND SOUND PRESSURE LEVEL, 0dB re 0.0002 MICRO BAR

COOLING

FUNCTION SPL(dB(A)) LINE

High

FAN SPEED

HEATING

10 63 125 250 500 1000 2000 4000 8000

NC-60

NC-50

NC-40

NC-30

NC-20

NC-70

BAND CENTER FREQUENCIES, Hz

NC-10

OCH530A

Otros manuales para Mr.Slim SUZ-KA25VA3

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PLFY-EP NEMU-E1 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. Slim MVZ Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MUZ-HJ25VA - E1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PFD-P250VM-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PVFY-P18 NAMU-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric M-SERIES Instrucciones de instalación y funcionamiento

Mitsubishi Electric

Mitsubishi Electric TRANE NTXSST A112AA Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-GS30NA2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MFZ-KA25VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PCA-RP KAQ Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MXZ-SM36NAM2 Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric MSZ-HC25VA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MUZ-EF25VG Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SLZ-KA50VAL Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PEFY-P20 VMS1-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.SLIM PEH Series Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric PQHY-P400-500YSGM-A Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MUZ-FH35VEHZ Manual de usuario

Mitsubishi Electric

Mitsubishi Electric NAXMMX60A182A Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUHZ-SW160YKA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUMY-P100VHMA Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric Mr.Slim MCF-18TN Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SLZ-KF25VA2 Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric MUZ-GC25VA-E1 Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario