Mitsubishi Electric Mr. Slim MS-A09WA Manual de usuario

SERVICE MANUAL

CONTENTS

1. TECHNICAL CHANGES ··································· 2

2. PART NAMES AND FUNCTIONS····················· 3

3. SPECIFICATION················································ 5

4. OUTLINES AND DIMENSIONS ························ 6

5. WIRING DIAGRAM············································ 7

6. REFRIGERANT SYSTEM DIAGRAM ··············· 7

7. SERVICE FUNCTIONS ····································· 8

8. TROUBLESHOOTING······································· 9

9. DISASSEMBLY INSTRUCTIONS···················· 21

10. PARTS LIST····················································· 24

10-1. PARTS LIST············································· 24

10-2. RoHS PARTS LIST ·································· 27

11. MICROPROCESSOR CONTROL···················· 30

Models

MS-A09WA

MS-A09WA - 1

MS-A12WA

MS-A12WA - 1

NOTE:

RoHS compliant products have <G> mark on the spec name plate.

For servicing of RoHS compliant products, refer to the RoHS PARTS

LIST (RoHS compliant).

INDOOR UNIT

Outdoor unit service manual

MU-A•WA Series (OB449)

Revision C:

• TEST POINT DIAGRAM AND VOLTAGE has

been corrected. (8-7)

Please void OB448 REVISED EDITION-B.

No. OB448

REVISED EDITION-C

MS-A09WA MS-A09WA -1

MS-A12WA MS-A12WA -1

1. Remote controller has been changed.

• Temperature indication function (°F/°C) has been added. (Refer to 11-8.)

Models Remote controller Temperature indication

MS-A09/12WA KM06C °F

MS-A09/12WA- 1KM07L °F/°C

• Timer indication has been changed. (AM/PM indication)

2. Conduit plate has been removed.

3. Conduit cover, terminal block cover and terminal block holder have been changed.

1TECHNICAL CHANGES

MS09TW MS-A09WA

MS12TN MS-A12WA

1.Indoor fan motor has been changed.

2.Signal of remote controller has been changed. (It is not available for conventional models.)

Revision A :

• MS-A•WA-1have been added.

Remote controller has been changed.

Revision B :

• SPECIFICATION has been corrected.

Powerful has been added. (Airflow ,Sound level)

Revision C:

• TEST POINT DIAGRAM AND VOLTAGE has been corrected. (8-7)

PART NAMES AND FUNCTIONS

MS-A09WA

MS-A12WA

Line flow fan

Air outlet

Vertical vane

Air inlet

Display section

Front panel

Panel

Heat exchanger

Horizontal vane

Operation section

(When the front panel is opened)

Remote controller

Remote control

receiving section

Catechin air filter

Air cleaning filter

(Anti-Allergy Enzyme

Filter, Blue bellows

type)

Emergency operation switch

Operation Indicator

lamp

ACCESSORIES

MS-A09WA

MS-A12WA

MS-A09/12WA MS-A09/12WA- 1

Installation plate 1 1

Installation plate ﬁxing screw 4 × 25 mm 8 5

Remote controller holder 1 1

Fixing screw for 3.5 × 1.6 mm (Black) 2 2

Battery (AAA) for remote controller 2 2

Wireless remote controller 1 1

Felt tape (Used for left or left-rear piping) 1 1

Conduit plate 1 —

SPECIFICATION

Model MS-A09WA MS-A12WA

Indoor unit model MS-A09WA MS-A12WA

External ﬁnish White

Power supply V, phase, Hz 115, 1, 60

Max.-fuse size (time delay) /

Disconnect switch A15

Min. circuit ampacity A 1.2

Fan motor F.L.A 0.95

Airﬂow

Low–Med.–High–Powerful

COOL

Dry (Wet) CFM 183 - 261 - 335 - 367

(162 - 233 - 300 - 328)

222 - 286 - 406 - 446

(198 - 254 - 363 - 399)

Moisture removal pt./h 2.7 3.2

Sound level

Low–Med.–High–Powerful dB(A) 26 - 32 - 40 - 42 33 - 38 - 45 - 47

Cond. drain connection O.D. in. 5/8

Dimensions

in.

30-11/16

D 8-1/4

H 11/-3/4

Weight Ib. 23

Remote controller Wireless type

Control voltage (by built-in transformer) 115 VAC

NOTE : Test conditions are based on ARI 210/240

1 : Rating conditions (cooling) — Indoor : 80˚FDB, 67˚FWB, Outdoor : 95˚FDB, (75˚FWB) Rated frequency : 60Hz

Operating Range

Indoor intake air temperature Outdoor intake air temperature

Cooling Maximum 95˚FDB, 71˚FWB 115˚FDB

Minimum 67˚FDB, 57˚FWB 67˚FDB

4OUTLINES AND DIMENSIONS

MS-A12WA

Unit : inch

MS-A09WA

11-3/4

424-9/16

30-11/16

8-1/4 3/16

2-1/8

3/4

6-1/4

2-5/16

Air in

Air out

Installation plate

6-1/8 6-1/8

7/8

1-3/4

13-3/16 12-5/8

1-5/8 8-7/16

10-1/8

1-11/16

8-7/16

1/8 11-5/16

2-3/4

2-3/16

2-3/16 2-3/16

8-7/8 8-7/8

9/1610-3/4

9-3/16

Wall hole 2-9/16

Indoor unit

Installation plate

7/16x13/16

Oblong hole

7/16x1 Oblong hole

7/8

hole

Conduit plate(MS-A•WA- is excluded.)

3/4 I.D

Insulation 1-1/8

Drain hose 5/8

(Connected part O.D)

Liquid line 1/4 19-11/16

Gas line 3/8 16-15/16

Insulation 1-3/8 O.D

{

WIRING DIAGRAM

REFRIGERANT SYSTEM DIAGRAM

MS-A09WA

MS-A12WA

Indoor

heat

exchanger

Flared connection

Room temperature

thermistor

RT11

Flared connection

Refrigerant flow in cooling

Refrigerant pipe 3/8 (MS-A09)

1/2 (MS-A12)

(with heat insulator)

Refrigerant pipe 1/4

(with heat insulator)

Indoor coil

thermistor

RT12

Unit : inch

MS-A09WA

MS-A12WA

7SERVICE FUNCTIONS

7-1. TIMER SHORT MODE

For service, set time can be shortened by short circuit of JPG and JPS the electronic control P.C. board.

The time will be shortened as follows. (Refer to 8-7.)

Set time : 1-minute 1-second

Set time : 3-minute 3-second (It takes 3 minutes for the compressor to start operation. However, the starting time is

shortened by short circuit-of JPG and JPS.)

7-2. P.C. BOARD MODIFICATION FOR INDIVIDUAL OPERATION

A maximum of 4 indoor units with wireless remote controllers can be used in a room.

In this case, to operate each indoor unit individually by each remote controller, P.C. boards of remote controller must be

modified according to the number of the indoor unit.

How to modify the remote controller P.C. board

Remove batteries before modification.

The board has a print as shown below :

Table 1

1 unit operation 2 units operation 3 units operation 4 units operation

No. 1 unit No modiﬁcation Same as at left Same as at left Same as at left

No. 2 unit — Solder J1 Same as at left Same as at left

No. 3 unit — — Solder J2 Same as at left

No. 4 unit — — — Solder both J1 and J2

How to set the remote controller exclusively for particular indoor unit.

After you turn the breaker ON, the first remote controller that sends the signal to the indoor unit will be regarded as the remote

controller for the indoor unit.

The indoor unit will only accept the signal from the remote controller that has been assigned to the indoor unit once they are

set.

The setting will be cancelled if the breaker has turned off, or the power supply has shut down.

Please conduct the above setting once again after the power has restored.

The P.C. board has the print “J1” and “J2”. Solder “J1” and “J2” according to the number of indoor unit as shown in Table 1.

After modification, press the RESET button.

NOTE : For modification, take out

the batteries and press

the OPERATE/STOP(ON/

OFF)button twice or 3

times at first.

After finish modification,

put back the batteries then

press the RESET button.

MS-A09WA

MS-A12WA

TROUBLESHOOTING

8-1. CAUTIONS ON TROUBLESHOOTING

1. Before troubleshooting, check the following

1) Check the power supply voltage.

2) Check the indoor/outdoor connecting wire for miswiring.

2. Take care of the following during servicing

1) Before servicing the air conditioner, be sure to turn off the unit first with the remote controller, and then after confirming

the horizontal vane is closed, turn off the breaker and/or disconnect the power plug.

2) Be sure to turn OFF the power supply before removing the front panel, the cabinet, the top panel, and the electronic

control P.C. board.

3) When removing the electronic control P.C. board, hold the edge of the board with care NOT to apply stress on the com-

ponents.

4) When connecting or disconnecting the connectors, hold the housing of the connector. DO NOT pull the lead wires.

MS-A09WA MS-A12WA

NOTE:

• The operation settings are memorized when 10 seconds have passed after the indoor unit was operated with the

remote controller.

• If main power is turned OFF or a power failure occurs while AUTO START/STOP timer is active, the timer setting is

cancelled.

• If the unit has been off with the remote controller before power failure, the auto restart function does not work as the

power button of the remote controller is off.

• To prevent breaker off due to the rush of starting current, systematize other home appliance not to turn on at the

same time.

• When some air conditioners are connected to the same supply system, if they are operated before power failure, the

starting current of all the compressors may flow simultaneously at restart.

Therefore, the special counter-measures are required to prevent the main voltage-drop or the rush of the starting

current by adding to the system that allows the units to start one by one.

JR07

CN151 CN211CN112 CN1R1

7-3. AUTO RESTART FUNCTION

When the indoor unit is controlled with the remote controller, the operation mode, the set temperature, and the fan speed

are memorized by the indoor electronic control P.C. board. The “AUTO RESTART FUNCTION” sets to work the moment

power has restored after power failure. Then, the unit will restart automatically.

Operation

If the main power has been cut, the operation settings remain.

After the power is restored, the unit restarts automatically according to the memory.

(However, it takes at least 3 minutes for the compressor to start running.)

How to release “AUTO RESTART FUNCTION”

Turn off the main power for the unit.

Solder the Jumper wire JR07 on the indoor electronic control P.C. board. (Refer to 8-7.)

Lead wiring Housing point

3. Troubleshooting procedure

1) First, check if the OPERATION INDICATOR lamp on the indoor unit is flashing on and off to indicate an abnormality.

To make sure, check how many times the abnormality indication is flashing on and off before starting service work.

2) Before servicing check that the connector and terminal are connected properly.

3) When the electronic control P.C. board seems to be defective, check the copper foil pattern for disconnection and the

components for bursting and discoloration.

4) When troubleshooting, refer to 8-2., 8-3. and 8-4.

4. How to replace batteries

Weak batteries may cause the remote controller malfunction.

In this case, replace the batteries to operate the remote controller normally.

RESET button

Insert the negative pole of the

batteries first. Check if the polarity

of the batteries is correct.

NOTE : 1. If RESET button is not pressed, the remote controller may not operate correctly.

2. This remote controller has a circuit to automatically reset the microcomputer when batteries are replaced.

This function is equipped to prevent the microcomputer from malfunctioning due to the voltage drop caused by the

battery replacement.

Press RESET button with tip end of ball point pen

or the like, and then use the remote controller.

Remove the front lid and insert batteries.

Then reattach the front lid.

Otros manuales para Mr. Slim MS-A09WA

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Acondicionador de aire de Mitsubishi Electric

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PLA-M EA Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PEAD-RP35JAQ Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI CMB-WP108V-GA1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PFFY-P20VKM-E Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUHY-200YMF-C Cómo utilizar

Mitsubishi Electric

Mitsubishi Electric PWFY-P200VM-E-AU Guía del producto

Mitsubishi Electric

Mitsubishi Electric PUHY-P200 Cómo utilizar

Mitsubishi Electric

Mitsubishi Electric Mr.Slim SLZ-KA09NA Manual de funcionamiento

Mitsubishi Electric

Mitsubishi Electric Mr.SLIM SLZ-KA25VAQ Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-FS09NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MLZ-KP12NA2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric SEZ-A12 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MSZ-SF25VE2 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MUFZ-KW25VG-E1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric City Multi Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric TRANE CITY MULTI TPLFYP-EM140 Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr.Slim PEA-RP100 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MFZ-KJ25VE Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CMY-R100VBK Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Mr. Slim MSZ-A09NA Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MFZ-KJ VE Series Manual de usuario

Mitsubishi Electric

Mitsubishi Electric MU-A08ND-c1 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric PUHZ-P200YKA3 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric CITY MULTI PLFY-WL-NEMU-E Series Manual de usuario

Manuales populares de Acondicionador de aire de otras marcas

Spheros

Spheros CC 355 Manual de usuario

Bosch

Bosch Climate 5000 SCI 24 CAS/ OU- OUE Manual de usuario

Panasonic

Panasonic CS-E12HKEW Manual de usuario

nedis

nedis ACMB1WT7 Manual de usuario

Samsung

Samsung AR KV Series Guía

Daikin

Daikin FCFV50A Manual de usuario

Fujitsu

Fujitsu Inverter ASBA30JFC Manual de usuario

Toshiba

Toshiba RAS-M10SMUV-E Manual de usuario

Daikin

Daikin FXLQ20MAVE Manual de usuario

Hitachi

Hitachi RAS-E24CAK Manual de usuario

CIAT

CIAT Magister 2 Series Guía

Bestron

Bestron AAC6000 Manual de usuario

Hisense

Hisense 7K Manual técnico

Frigidaire

Frigidaire FFRE0533S1E0 Manual de usuario

Samsung

Samsung AS09HM3N Manual de usuario

Frigidaire

Frigidaire CRA073PU11 Manual del propietario

Soleus Air

Soleus Air GB-PAC-08E4 Manual de usuario

McQuay

McQuay MCK020A Manual de usuario