MIRABELLA HKWL-IR02W Manual de usuario
IR Transceiver User Manual
HKWL-IR02W
1. PRODUCT OVERVIEW This Smart IR is a Wi-Fi based IR Blaster. By adding or DIY learning the IR
codes to the APP, it can remotely control IR based home appliances such as TV’s, airconditioners
etc. via internet connection and the Mirabella Genio phone APP.
2. PRODUCT FEATURES
⚫Compatible with Amazon Alexa and Google Assistant
⚫Working in 802.11 b/g/n 2.4GHz wireless network (no hub required)
⚫Wi-Fi network configuration with EZ (Smart Config) and AP(Access Point) mode
⚫Remote control all your IR appliances through APP
⚫A full list of IR brands saved in IR codes cloud library
⚫DIY IR codes learning, control whatever appliance through your mobile
⚫Input: 5V 1A Micro USB
⚫CE, FCC, RoHS certified
How to Get the device working：
⚫Make sure your Wi-Fi network work in 802.11 b/g/n 2.4GHz and internet available;
⚫Download the Mirabella Genio APP from Apple store or Google Play;
⚫Register an account in APP and login with your email address or Mobile phone number;
⚫Setup the device Wi-Fi connection with your APP;
⚫Test and check the Device and APP working state;
⚫Check working with Alexa and Google Home if necessary;
3. PRODUCT STRUCTURE
Button activities and LED indicator:
1) Power connector：5V 1A Micro USB
2) Button: Press and hold the button for 5 seconds to enter into Wi-Fi connection (or
configuration). The LED indicator will blink rapidly (EZ mode) or slowly (AP mode). EZ mode
connection is set as default in Wi-Fi configuration. Press and hold the button for 5 seconds will
enable the device switch between EZ mode and AP mode.
3) LED indicator: indicate the device working state
EZ/AP Mode: Indicator flash rapidly / flash slowly
Network connected, normal working state: Indicator keeps on
Reset Button
LED Indicator
Power connector
Network connected, sending data: Indicator flashes one time
Enter learning mode: Indicator turns off
Receive Learning IR code command: Indicator turns on
4. SPECIFICATIONS
Input voltage range
5V
Operating Current
110mA
Battery
Micro USB power adapter with 5V/1A
IR Emitting Wavelength
940mm
IR Distances
8M
IR Learning Distances
3CM
IR Angle
360º
IR receiving frequency
38 KHz
Radio Frequency
2.412-2.484GHz
WIFI standard
IEEE802.11b/g/n (channel 1-14)
Data transmission rate
11b:1,2,5.5,11(Mbps)
11g:6,9,12,18,24,36,48,54(Mbps)
11n:HT20 MCS0-7
Operating temperature
-10℃~40℃
Storage temperature
-20℃~+60℃
Relative humidity
8%～80%
5. INSTALL APP AND REGISTER AN ACCOUNT
5.1 Scanning the following QR code to download APP for Android and iOS System. Or you can
download the APP named as “Mirabella Genio” from Apple store and Google Play.
5.2 Launch the APP and register an account with your email address then login;
i) Download APP and install ii) Register the APP
Android & iOS
6. ADD AND REMOVE DEVICE IN YOUR APP ACCOUNT
6.1 Launch the APP and login, Click ADD DEVICES or + -> All -> Infrared Universal Remote Control
to start the device adding.
6.2 TWO WAYS TO ADD DEVICES
⚫EZ mode
Smart IR will blink fast in red when powered on in EZ mode. Input the password of the
designated Wi-Fi network to include the device to Cloud. Waiting for around 30 seconds before the
device inclusion process is complete.
⚫AP mode
Smart IR will blink fast in red when powered on. Press and hold the button for 5 seconds and then
release. The LED indicator will blink slowly in red. Choose AP Mode, select the Wi-Fi network your
mobile is connected to and enter the Wi-Fi password. Select the Device AP name with SmartLife-
xxxx in Wi-Fi list then back to App to finish the device adding.
6.3 Users can re-name or share the device after Wi-Fi connection is finished.
Make sure the device is working in EZ/AP mode, if the APP works in EZ/AP mode.
6.4 Remove device
1) Click “ ” to enter into next interface as shown in picture below, Click “Remove Device” to
delete this device from APP; click “Restore manufacturer Defaults” to remove the device from APP.
2) After remove device or Restore manufacturer defaults from the APP, repeating the Wi-Fi
network inclusion steps to include the device to a new Wi-Fi network.
7. SEARCH AND ADD IR CODES
7.1 Adding IR Codes from existing brand list
1) Enter into Device user interface after network inclusion, then press “ ” and you can search
and add the IR remote controller of Set-Top Box (STB), TV or air conditioner etc. from the
existing brand list in the APP, here are Skyworth TV as example.
Enter into Skyworth remote control interface and click the power button. If the power button
works (means to turn on/turn off TV), click “Select this one”, then Skyworth TV remote control is
added in list. Click “Add remote control” to add next one.
7.2 Add IR codes by DIY learning
1) Click “DIY”, then click “Next step” to enter into DIY learning mode.
On DIY learning, place remote controller at position ①on the smart IR blaster (shown as below pic
ture) within 3CM so that the IR codes could be completely learned. Then short press the button th
at you want to learn on remote controller. It will come into next step after DIY learning is finished.
Name this button and save it.
Note: Short press means press the button in IR remote controller shortly (Press then release in 0.5
to 1 second)
Click “Edit” on upper right corner of DIY interface to make changes.
8. QUICK GUIDE OF USING AMAZON ECHO TO CONTROL SMART DEVICES
8.1 What you need to get started
Before using Echo to control your smart devices, please make sure that the following conditions are
met:
⚫Stable Wi-Fi network which could access to Amazon server.
⚫An Echo device, such as Echo, Echo Tap, or Echo Dot.
⚫A valid Amazon Alexa account.
⚫Mirabella Genio APP and a registered account.
⚫At least one device under your Mirabella Genio account.
8.2 Add devices in Mirabella Genio app (Refer to App Instruction)
You can skip this part if you've already added some devices to your Mirabella Genio account.
⚫Download Mirabella Genio app(Refer to App Instruction)
Search "Mirabella Genio" in App Store or Google Play to install the app.
iOS version download: App Store
Android version download: Google Play
⚫Register a Mirabella Genio account and sign in the app (Refer to App Instruction)
⚫Add device and re-name the device (Refer to App Instruction)
8.3 Link Mirabella Genio account to Echo
1) Tap "Skills" in the hamburger menu, then search "Mirabella Genio". Select "Mirabella Genio" and
tap "ENABLE" to enable the Skill.
2)You will be re-directed to the account link page. Type in your Mirabella Genio account and
password, don't forget to select the country/region where your account belongs to. Then tap "Link
Now"to link your Mirabella Genio account. The country/region, the account, and the password must
Match exactly/be the same with the Mirabella Genio account. Close the window when “Alexa has
been successfully linked with Mirabella Genio”notice is prompted out.
8.4 Control your smart devices through Echo
⚫Discover devices
Echo needs to discover your smart devices for voice control. You can say "Alexa, discover devices"
to Echo. Echo will discover devices which have already been added in the Mirabella Genio app.
You can also tap "DISCOVER" to discover the smart devices. Discovered devices will be shown in the
list.
Note:
❖Echo needs to go through “Discover”again after the device is re-named on Mirabella Genio APP.
❖If the Echo cannot find the devices added in Mirabella Genio APP, please disable the Mirabella
Genio skill first and go through the Mirabella Genio skill “ENABLE”, APP account login and device
discover again to make Echo voice control work.
⚫Voice control your devices
Now you can control your smart devices through Echo. Here below is an example of how to voice
control the device “TV”with Echo:
❖Alexa, turn on/off TV
❖Alexa, channel up/down on TV
Tabla de contenidos
