MINOURA M60-D Manual de usuario

Indoor Bicycle Trainer – instructions manual

Minoura Japan Headquarters Minoura North American Tech Center

(for all customers) (for U.S. residents only)

1197-1 Godo, Anpachi, Gifu 503-2305 Japan 1996 East Avenue, Hayward, CA 94541 U.S.A.

Phone: +81-584-27-3131 / Fax: +81-584-27-7505 Phone: 1-510-538-8599 / Fax: 1-510-538-5899

Email: [email protected] Email: [email protected]

www.minoura.jp

Made in Japan

M60-D

Read this instructions carefully before use

Tire Size Capacity Range<with Z-Adaptor> 26x1.00 - 29x2.10

<w/o Z-Adaptor> 20x1-3/8 - 700x32c

(ver.1.1 2010/2)

IMPORTANT NOTICE

• For use with a normal 2-wheel bicycle only. Do not use a tandem, recumbent, or other.

• Hub nut type rear wheel axle is not compatible with M60-D in standard.

You need to replace the left side coupling (UF-8) with optional "Left Side Coupling for

Hub Nut Axle".

• Fits tire size between 20x1-3/8" and 29x2.10". To use 26x1.00" or smaller tire, install

the optional Small Wheel Adaptor.

• Some assembly required. Use correct tools (10mm spanner & M4 hex wrench).

Tools are not supplied in the kit.

• Use the supplied rear quick release skewer for maximum stability.

Minoura is not responsible for any problem caused from using your own skewer.

• Use on at and level oor or ground for your safety.

• Adjust the roller pressure to the rear tire properly in order to maximize your tire life.

Tire and roller contact will eventually wear both your tire and the trainer roller.

• Adjusting the resistance must be done with the bike stopped. Do not operate the

adjustment lever (EM-13) while the rear wheel is spinning.

• Touching the spinning wheel and/or any other moving parts while training may cause

serious injury. Keep children and pets away from the trainer when in use.

• It is not possible to convert the non-remote resistance unit to the remote control

version one due to a difference in the inside mechanism.

• If you feel any strange noise or smell, stop using M60-D immediately and contact the

retailer where you purchased the M60-D.

• Any warranty will be void if you use M60-D for other purpose than instructed.

Minorua offers 1-year limited warranty on the resistance unit and 5-year limited

warranty on the frame from the date of your purchase for any problem caused by

manufacturer's defect.

Any damage or problem caused by transporting process is not covered under warranty.

Any damage from shipping or moving must be made to the shipping company.

Read enclosed "Minoura Limited Warranty Policy" card for more detail.

- Page 2 -

BF-2: M60 Main Frame (Blue) EM-1: Outer Cap

BF-5: Leg Rubber Cover (White) EM-2: Axle Holder

BF-6: Leg Rubber EM-3: Drive Roller & Bearing

UF-7: Clamp Lever Guide EM-4: Main Housing

UF-8: Left Side Coupling (for Q/R skewer) EM-5: Alloy Rotor

UF-17: Right Side Coupling & Clamp Lever EM-11: Connecting Plate

UF-18: Coupling Lock Ring (White) EM-13:Resistance Adjust Lever

M5-2: Rubber Foot Cap (29mm) EM-16:Magnet Plate (for M60-D)

MF-3: Roller Pressure Adjust Knob EM-17:Flywheel Disc (0.6 kgs)

LM-10: Base Plate EM-18:Flywheel Cover (White for M60)

UF-18

UF-8

UF-17

UF-7

M5-2

BF-5

BF-6

BF-5

BF-6

MF-3

EM-1

EM-2

LM-10

EM-11

EM-3 EM-4

EM-5

EM-16

EM-17

EM-18

EM-13

BF-2

M60-D Schematics

- Page 3 -

3. Fully open both legs and place M60-D on a at

and level oor. (see Fig. B)

At this moment, make sure all 4 foot are

contacting the oor at once to sit on the oor

stable.

How To Setup Your M60-D Trainer

2. Install the Mag unit and the Roller Pressure Adjust

Knob set (MF-3) to M60-D. (see Fig. A)

Remove the pre-installed bolt from Base Plate

(LM-10).

Attach Mag unit to the bracket on frame, align the

holes, and put through the bolt.

Tighten the bolt with 10mm spanner and M4 hex

wrench.

- Page 4 -

1. Replace your rear wheel quick release skewer to the supplied one.

Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape.

If your bike is not equipped with quick release skewer and it's a hub nut type,

replace the left side coupling (UF-8) to the optional "Left Side Coupling for Hub

Nut Axle".

Minoura doesn't guarantee the stability if you don't replace the left side coupling.

You don't need the supplied quick release skewer if your wheel is a hub nut type.

It's not possible to convert your wheel from the hub nut type to the quick release

skewer type unless replacing the hub.

Required Tools: 1 x 10mm Spanner

1 x M4 Hex Wrench

Do not overtighten the bolt,

otherwise the Mag unit will

not move smoothly even if

you rotate the knob.

If properly installed,` the

Mag unit will come down

slowly with its own weight

when you release it.

Install the knob set to the welded nut on the bracket.

Make sure the acorn shaped spring

direction is as shown in Fig. A.

Failure will cause difculty on rotating.

(Fig. A)

(Fig. B)

4. Place your rear wheel in between the couplings.

1) Loosen the lock ring (UF-18) to allow the

left side coupling (UF-8) be free. (see Fig. C)

2) Pull up the quick hub clamp lever (UF-17)

to retract the right side coupling. (see Fig. D)

3) Insert the left side (quick lever side) skewer

into the left side coupling rst.

The quick lever shaft must be inserted into the

cut-out on the coupling to hold the bike stable.

Turn the coupling to adjust the cut-out position.

4) While keeping this position, slowly come

down the bike to align the right side acorn nut

to the right side coupling.

(Fig. C)

(Fig. D)

(Fig. E)

(Fig. F)

5) Push down the quick hub clamp lever to hold the rear wheel. (see Fig. E)

If you start feeling resistance when the lever comes at 4 o'clock position, it's correct.

If the clamping hub is too tight or too loose due to wrong position of the left side coupling, pull up the

lever to release the bike, adjust the left side coupling position and try clamping the hub again.

6) Lastly, tighten the lock ring to x the left side coupling position. (see Fig. F)

Both left and right side couplings are

designed to suit the supplied quick release

skewer. The left side coupling must t

perfectly in the skewer head to get correct

stability. (see Fig. G)

Any skewer type which lever is located on

the end of the axle (Fig. H) or the lever will

not be bent over right angle (Fig. I) cannot

be used on M60-D.

(Fig. G)

(Fig. H) (Fig. I)

Precisely adjust the left side coupling

position to keep the correct thightness of

rear hub clamping.

Too tight setting will cause damage to both

M60-D and your bike frame.

Too loose setting may cause the bike to

come out of the trainer during use.

- Page 5 -

6. The rear tire should sit in the almost center part of

the Drive Roller without touching any other parts.

(see Fig. L)

If the tire has touched the plastic parts (Fig. M)

due to some reasons like the rear wheel is not trued

correctly or you have installed a too fat tire, you must

adjust the Mag unit position.

To do so, loosen the backside screws with M5 hex

wrench, adjust the roller position, then tighten the

screws again tightly. (see Fig. N)

5. Contact the Drive Roller to the rear tire by turning the Roller Pressure Adjust Knob clockwise. (see Fig. J)

The best position is that the roller compresses the tire in the depth of 3 - 4 mm. (see Fig. K)

- Page 6 -

(Fig. L)

(Fig. N)(Fig. M)

(Fig. J) (Fig. K)

Please note too much and too less roller pressure will bring premature tire wear.

Keep correct roller pressure and maintain the air pressure in correct level before

using M60-D.

If it's hard to tighten the knob bolt, lift up the Mag unit by hand then tighten the knob.

TIPS

How To Adjust Resistance Level

M60-D provides 3 different resistance levels to suit your

training level.

To Increase Resistance Level:

Slide the Dial Lever toward "H" position.

To Decrease Resistance Level:

Slide the Dial Lever toward "L" position.

If the rear tire has touched any other parts than the Drive Roller, the part may be

damaged and your tire will wear out quickly.

It is impossible to adjust the rear wheel position by adjusting the left side coupling

position. It just works to adjust the coupling distance.

If you wish to use the tire sized 26x1.0" or smaller,

you need to install the optional Z-shaped "Small

Wheel Adapter" between Base Plate and Mag unit to

raise up the roller height.

The direction of Z-adapter is xed so follow the

arrow printed on the top and make sure it's pointing

toward the front (toward your bike).

If the drive roller cannot reach the tire even if you

install the adaptor, make sure you have been installed

in correct direction.

Use the original cap head bolts for Base Plate, and

use the supplied hex head bolts for the Mag unit.

How To Use Small Wheel Adaptor (option)

Hex Head Bolt

Cap Head Bolt

Z-Adaptor

(in case of GYRO V270)

5. To remove the bike from M60-D, loosen the knob then lift up om the clamp.

If you remove the bike without changing the roller position, the next installation may become difcult

because the rear wheel has been pushed forward by the roller.

Required Tools: 1 x 10mm Spanner

1 x M5 Hex Wrench

- Page 7 -

Tabla de contenidos

Otros manuales de Bicicleta estática de MINOURA

MINOURA

MINOURA Minimag M20-D Manual de usuario

MINOURA

MINOURA B60 Manual de usuario

MINOURA

MINOURA LiveRide LR960 Manual de usuario

MINOURA

MINOURA LiveRide LR340 Manual de usuario

MINOURA

MINOURA B60-D Manual de usuario

MINOURA

MINOURA MAG-850 Manual de usuario

MINOURA

MINOURA VFS150 Manual de usuario

MINOURA

MINOURA liveride lr240 Manual de usuario

MINOURA

MINOURA FG540 HYBRID ROLLER Manual de usuario

MINOURA

MINOURA MAG-500 Series Manual de usuario

MINOURA

MINOURA MAG-850 Manual de usuario

MINOURA

MINOURA LiveRide LR961 Manual de usuario

MINOURA

MINOURA VFSG-9 Manual de usuario

MINOURA

MINOURA LiveRide LST9200 Manual de usuario

MINOURA

MINOURA moz-roller Manual de usuario

MINOURA

MINOURA V270 Manual de usuario

MINOURA

MINOURA M70-R Manual de usuario

MINOURA

MINOURA LiveRide LR341 Manual de usuario

MINOURA

MINOURA LiveRoll R720 Manual de usuario

MINOURA

MINOURA LiveRide FG220 Manual de usuario

MINOURA

MINOURA SmartTurbo KAGURA LSD9200 Manual de usuario

MINOURA

MINOURA V270 Manual de usuario

MINOURA

MINOURA VFS3R - SCHEMATICS Manual de usuario

MINOURA

MINOURA SmartTurbo Kagura EHT1020 Manual de usuario

Manuales populares de Bicicleta estática de otras marcas

Weslo

Weslo Vector 302 Guía de inicio rápido

TOORX

TOORX BRX85 Manual de usuario

Matrix

Matrix KranKcycle Manual de usuario

Matrix

Matrix IC3 Manual de usuario

Sunny Health & Fitness

Sunny Health & Fitness SF-B121021 Manual de usuario

Monark

Monark 827E Manual de usuario

Stamina

Stamina 1310 Manual de usuario

American Fitness

American Fitness SPR-BK1072A Manual de usuario

Cateye

Cateye CS-1000 (CYCLO SIMULATOR) Manual de usuario

BH FITNESS

BH FITNESS H9158H Manual del operador

Body Sculpture

Body Sculpture BC-7220G Manual de usuario

Cateye

Cateye EC-2300 Manual de usuario

FYTTER

FYTTER RACER RC MSR Manual de usuario

Kikos

Kikos HM-9090M Manual de usuario

Pro-Form

Pro-Form 345 Zlx Bike Guía del usuario

Fuel Fitness

Fuel Fitness SU135-40 Manual de usuario

NordicTrack

NordicTrack Gxr 4.2 Bike Manual de usuario

Vision Fitness

Vision Fitness U70 Manual de usuario