Minelab gpz 7000 Manual de usuario
Instruction Manual
ii
WARNING
THIS DOCUMENT CONTAINS INTELLECTUAL PROPERTY, TECHNICAL AND PROPRIETARY DATA AND INFORMATION AND OTHER MATERIAL OWNED SOLELY BY MINELAB
ELECTRONICS PTY LIMITED.
THIS MATERIAL MUST NOT BE USED WITHOUT THE PRIOR WRITTEN PERMISSION OF MINELAB ELECTRONICS PTY LTD.
© MINELAB ELECTRONICS PTY LTD. ALL RIGHTS RESERVED
This document is protected by copyright. Apart from any use permitted under the Australian Copyright Act 1968 (Cth) or other applicable laws, any unauthorised use,
appropriation or reproduction of this document or any part of it is strictly prohibited. No part of this document may be used or reproduced by any means or by any process,
in any form, without the prior written permission of the copyright owner Minelab Electronics Pty Ltd of 118 Hayward Avenue, Torrensville, SA 5031, Australia.
ComplIANCe
Information to the User (FCC Part 15.105)
NOTE: Class B Devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment of and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
DIsClAImeR
The Minelab metal detector discussed in this instruction manual has been
expressly designed and manufactured as a quality hobbyist metal detector
and is recommended for use in coin, treasure and general metal detection in
nonhazardous environments. This metal detector has not been designed for use as
a mine detector or as a live munitions detection tool.
pleAse Note
Since there may be a variety of options available for this detector, equipment
may vary according to the Model or items ordered with your detector. Certain
descriptions and illustrations may also differ (in this manual) from the exact Model
that you purchased. In addition, Minelab reserves the right to respond to ongoing
technical progress by introducing changes in design, equipment and technical
features at any time.
Minelab®, Smartfind™ 2, Wi-Stream™, GPSi™, FindPoint®, GeoHunt™, GeoTrail™, XChange Your Detecting Connection™, Target Trace™ are trademarks of Minelab Electronics Pty.
Ltd. Google Maps is a trademark of Google Inc. u-blox is a trademark of u-blox Holding AG.
CAUtIoN
Before assembling, charging, or using your detector for the first time, please read the important
legal and safety information in this manual.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand the
hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
Contents
iii
Detector Parts 1
Assembly 3
Assembling the Detector 3
Connecting Headphones 5
WM 12 Audio 5
Detector Audio 5
Changing Coils 6
Swing Arm 6
Harness and Extras 6
Charging Batteries 7
BC 10 Battery Charger 7
Battery LED 7
Power LED 7
GPZ 7000 Battery 7
Recharge the Lithium-Ion Battery Pack 8
WM 12 Battery 8
Recharge the WM 12 8
Control Panel 9
GPZ7000 User Interface 10
Typical Screen Elements 10
Status Bar Elements 10
Summary of Status Bar icons 10
Types of Selection Screens 11
Menu Navigation 12
Navigating the Detector Settings Pages 12
Navigating the Map Pages 12
Map 13
Map 13
GPS 14
Map Elements 14
Zoom Levels 15
Start Trail 15
Current Position 15
FindPoints and WayPoints 15
GeoTrail 15
GeoHunts 15
North Marker 15
Coordinates 16
Navigation Tool 16
Detector Settings Menu 17
Detector Settings Menu Structure 17
Detect Page Overview 17
Detect Plus Page Overview 17
Settings Page Overview 17
Preferences Page Overview 17
User Button Page Overview 17
Reset Page Overview 17
Detect 18
Quick Start 18
Target Type 18
Small Nuggets 18
General 18
Deep Only 18
Ground Type 18
Difficult 18
Normal 18
Noise Cancel 19
Auto Noise Cancel 19
Manual Noise Cancel 19
Sensitivity 19
Adjust Sensitivity Settings 19
Volume 19
Detect Plus 20
Threshold Level 20
Volume Limit 20
Threshold Pitch 21
Ground-Balance Mode 21
Auto 21
Manual 21
Settings 22
GPS 22
Backlight 22
Backlight Brightness 22
Wireless Enable 22
Connect WM 12 22
Connect Additional WM 12 22
Pairing an Additional WM 12 22
Removing Additional WM 12’s 22
Preferences 23
Time Zone 23
Time Format 23
Coordinates Format 23
Length Units 23
Weight Units 23
Wizards 23
User Button 24
Assign a Function to the User Button 24
User Button Functions 24
Backlight 24
View Coordinates 24
View Navigation Tool 24
Threshold Level 24
Ground Balance Mode 24
Other 24
Reset 25
Reset GeoStore 25
Reset Settings 25
Reset All 25
Contents
iv
Language 25
Change the Language 25
Product Verification Code 25
Version Information 25
Map Menu 26
Map Menu Structure 26
Map Overview 26
GeoStore Page Overview 26
Display Page Overview 26
Create GeoData Page Overview 26
GeoStore 27
Open the GeoStore Menu 27
Map Zoom 27
Sort FindPoints/WayPoints 27
Go to a FindPoint or WayPoint 27
Go to Start/End of a GeoHunt 28
Delete a GeoStore Item 28
Display 29
Open the Display Page 29
Show or Hide Map Screen Elements 29
Recentre 29
Clear Trail 29
View Trail 29
View Navigation Tool 29
View Names 29
View Coordinates 29
Create GeoData 30
Create and Store FindPoints and WayPoints 30
Control a GeoHunt 30
Record a GeoHunt: 30
Pause a GeoHunt: 30
Stop a GeoHunt: 30
Loss of Power during a GeoHunt 30
Loss of GPS Position Fix during a GeoHunt 30
Wireless Audio Module 31
Connect the WM 12 31
Reset the WM 12 31
Minelab XChange2 32
Communicating between GPZ 7000 and your PC 32
System Requirements 32
Install XChange 2 on your PC 32
Start the XChange 2 Application 32
Connect GPZ 7000 to your PC 32
Detecting Basics 33
Holding the Detector 33
Adjust the Length of the Shafts 33
Adjust the Angle of the Coil 33
Sweeping the Coil 33
Types of Targets 33
Detector Sounds 34
Detecting Tips and Techniques 34
Simple Detecting Exercise 35
Pinpointing 36
Locating the target. 36
Target Recovery 37
Recovering the Target 37
Detector Care and Safety 38
Battery Care and Safety 39
GPZ7000 Accessories 40
Factory Presets 41
Detect Presets 41
Detect Plus Presets 41
Settings Presets 41
Preferences Presets 41
User Button Presets 41
Display Presets 41
Technical Specications 42
GPZ 7000 Technical Specifications 42
Battery Technical Specifications 42
BC 10 Battery Charger Technical Specifications 42
Detector Parts
1
* Coil is waterproof to 1m
Battery Pack
Battery Latches
Stand
Control Box
Trigger Upper Cam Lock
Lower Cam Lock
Lower Shaft
Coil*
Headphone Module
Control Panel
Handle
Armrest
Armrest Strap
Armrest Lock
USB Connector
Mid Shaft
Upper Shaft
Detector Parts
GPZ 7000 is not waterproof
Detector Parts
2
See page 39 for the list of accessories available for use
with the GPZ 7000.
Items may vary from those shown.
Assembly
3
Assembly
Assembling the Detector
Attach coil and lower shaft to mid shaft
1. Release the camlock on the lower shaft by pulling
the lever away from the lower shaft
2. Thread the coil cable up the centre of the mid shaft.
3. Insert the mid shaft into the lower shaft. The lower
shaft can only be inserted into the mid shaft in one
orientation. Ensure that the key stop on the mid shaft
is aligned to the upper shaft.
4. Lock the camlock by pushing the lever towards the
shaft.
Attach mid shaft to upper shaft
1. Release the cam lock on the upper shaft by pulling
the lever away from the shaft.
2. The mid shaft can only be inserted into the upper
shaft in one orientation. Ensure that the key stop on
the mid shaft is aligned to the upper shaft.
3. Slide the mid shaft into the upper shaft until the coil
cable and key stop appear at the top.
4. Rotate lower shaft and coil 90° so that the coil is
oriented as shown.
Assembly
4
5. Lock the cam lock by pushing the lever towards the
shaft
Attach control box
WARNING
PINCH POINTS - CONTROL BOX
Take care when sliding the control box onto
the chassis and when operating the control box latch.
1. Slide the control box partly onto the upper shaft.
When it reaches half way it will click into place to
prevent the control box from sliding while the
connectors are fitted.
1. Attach the coil and control panel cables to their
respective connectors, and firmly tighten the
retaining rings.
2. Slide the control box further along the upper shaft
until it locks into place.
Attach battery and headphone module
It is a good idea to go detecting with a fully charged battery.
See page 6 for information on how to recharge the
GPZ 7000 battery.
1. Fit the battery pack onto the control box and close
the latches to secure it in place.
2. Fit the headphone module onto the control box. Use
a screwdriver or coin to gently tighten the bolt taking
care not to damage the thread by over-tightening.
Assembly
5
Attach Armrest
1. Lift the armrest lock until it is fully open. Slide the
armrest onto the rail on top of the chassis. Ensure
that the sloping sides of the armrest face toward the
control panel.
2. Hold the detector as if detecting and slide
the armrest along the rail until it is positioned
comfortably just below your elbow.
3. Remove your arm from the armrest and push down
the armrest lock to secure the armrest in position.
Adjust Armrest Strap
1. Undo the hook and loop armrest strap.
2. Tighten the strap until your arm is secure in the
armrest, and fasten.
tIp
To fit a smaller arm, the strap can be fitted
upside down and passed through the
armrest three times.
Connecting Headphones
The headphones can be connected directly to the
detector or to the WM 12.
It is recommended that the WM 12 is used to generate audio.
WM12 Audio
To generate audio via the WM 12, Plug the headphone
connector into the WM 12 headphone socket. The WM 12
must be paired with the detector to hear audio
(page 21).
Note
The WM 12 can be used without
headphones, as it has an in-built speaker.
More information on the WM 12 on
page 30.
Detector Audio
Alternatively, you can connect headphones directly to the
detector. To do this, plug the headphone connector into
the socket on the headphone module at the rear of the
detector.
If using waterproof accessory headphones, you will need
to remove the headphone module from the control box
and connect the headphones to the exposed headphone
socket, remembering to tighten the retaining rings
Charging Batteries
6
Changing Coils
A range of accessory coils are available for your GPZ 7000.
To change a coil, follow the ‘Assembling the detector’
steps with the alternative coil.
Always check that the coil connector is dry and free of grit
and dust before connecting to the detector.
Note
All Minelab GPZ 7000 coils come with
the lower shaft pre-assembled to the coil.
Disassembling a coil from its lower shaft is
not recommended.
Swing Arm
Harness and Extras
Otros manuales para gpz 7000
2
Tabla de contenidos
Otros manuales de Sensor de seguridad de Minelab
