Minebea CSD-581-15 Manual de usuario
DIGITAL INDICATOR
CSD-581-15
Instruction Manual
EN294-1107-M
I
FOREWORD
Thank you very much for your purchasing our Digital Indicator CSD−581−15.
This manual explains installation procedures and connecting method and also operating
method for Digital Indicator CSD−581−15. Make use of it properly after reading through
the manual carefully.
Be sure to deliver the manual to the end user. Moreover, the end user should keep the
manual at hand after reading it over.
II
Marks and arrangement used in this manual
The following marks are attached to the explanation on the matters that indicate
“Don’t do this.”, “Take care.” and “For reference”.
Be sure to read these items where these marks are attached.
Warning ● It means a precaution which must be followed to prevent the
possibility of accident or serious injury to the operators.
To avoid possible hazard, don’t perform any procedure described
here.
●It means precautions and important informations for safe operation
and service personnels. Be sure to read to prevent from malfunction.
Mark during operation
●Press the switch.
III
For safe operation
Be sure to read this manual before use.
1. Installation place
●Use the instrument where the temperature/humidity specifies within
the range as follows:
Environmental temperature：−10 ℃to 50 ℃
Environmental humidity：Less than 85 %R.H.(Non condensing.)
(1) Location where installation is not allowed.
Warning ●Don’t locate the instrument on the places such as follows:
It may cause an unexpected faulty in the instrument.
DDon’t expose the instrument in direct sunlight and/or high temperature
area.
DDon’t use the instrument in a high humid area.
DDon’t install the instrument where there is high mechanical vibration.
DDon’t use the instrument where there is an excess of dusts and fine
particles.
DDon’t install the instrument where there includes any corrosive gas or any
salty atmosphere.
DDon’t install the instrument where there is rapid change of temperature
and humidity.
DDon’t install the instrument near the devices that are magnetized or
generate an electromagnetic field.
DDon’t install the instrument where there may suffer radioactivity or
radioactive rays.
DAvoid the location where chemical reaction may take place such as in a
laboratory.
IV
(2) Installation
Warning ●There are a lot of electrical parts installed on the P.C. board of the
instrument, so there have fears to occur electrostatics destruction.
Because of this, operator should discharge electricity from him/her by
touching to some metal sections other than the instrument before
use. Besides, take care not to touch to electrical parts when you
operate.
●When installing the instrument, install as referring to the following
dimensions and secure the space around the instrument.
●When installing the instrument, we recommend you to prepare for
the cover considering the following items.
Besides, we prepares installation to cover for this instrument as an
option.
1 There are a lot of ICs on the P.C. board of the instrument that may
be destroyed eternally due to static electricity, so in order to
prevent the human from touching them directly.
2The battery is installed on the P.C. board of the instrument, so in
order to prevent from shorting between the polarities of battery
carelessly.
3There are some places that have high temperature around 50 ℃or
more in the room temperature, so in order to prevent the operator
from touching to the areas carelessly.
●The protection tape for the battery polarities is applied on the part of
battery(front side) and battery terminal(rear side) of this instrument.
When you will use the instrument, peel them off
●The bag for packaging this instrument is made from the conductive
material, so don’t use this bag with the protection tape for each
battery polarities removed.
V
Each dimensions of the instrument and required dimensions for the environmental
spaces are as follows:
Dimensions for installation
220
113
497 115
122
130
4
6−φ4 land □6
9
1.6
25
(25)
4
4
Required space for application
Required space for application
Unit：mm
Dimensions when the optional metal cover(CSD581−P80) is installed.
250
240
5(5)
4−φ6
(152.5) (73) (24.5)
(19) 140
100 20(20)
1
(37.6)
Unit：mm
CN202
DIP202 DIP203
VI
2. Power supply
Warning ●Be sure to check that power supply is off when installing each cable.
If the work is done with the power fed, there may have the possibility
of electric shock to the operator or even the possibility of destroying
the instrument.
●Before supplying the power, check that the indication of power supply
voltage/specifications for the instrument and the power going to
supply should be the same. If they are not equal, contact us.
If you use the instrument without checking them, it may
cause a damage in the instrument or electric shock to the operator.
●Grounding wire should be grounded securely. When grounding wire is
not connected, it may cause a malfunction of the instrument or
electric shock to the operator.
3. Application note
Warning ●Before using a new instrument or exchanging the strain gage applied
transducer for a new one, be sure to make calibration.
If calibration shall not be made, correct measured results may not be
obtained nor it may cause a malfunction in the instrument and there
may exist damage in peripheral equipments.
Besides, even though calibration had been made, there may occur the
similar case when the result is not correct, so make calibration again.
Warning ●In case of using the instrument, check that the connections are
executed properly. If not connected properly, correct measured result
will not be obtained, nor it may cause malfunctions of the
instrument, damage to the peripheral equipments or even worse
serious accidents.
Warning ●When change of setting is made carelessly on the instrument during
measurement, it may cause malfunction in the instrument and also
possibility of damage in peripheral equipments.
VII
Warning ●Do not shock the instrument such as throwing something on it.
If neglected, it may cause destruction of the parts and damage to the
electrical circuits.
Warning ●Don’t push the key switch section on the instrument with
unnecessary strong force nor push it with sharp−edge object such as
driver. If neglected, it may cause a damage to the key switch and even
have the possibility of damage to operational performance.
Warning ●Don’t remove the parts of the instrument, nor take the instrument
into pieces. If neglected, it may cause a damage to the parts and even
have the possibility of damage to the electric circuits.
Warning ●There are a lot of electrical parts installed on the P.C. board of the
instrument, but take care not to touch them. If neglected, there may
cause electrostatics destruction.
Warning ●The P.C. board of the instrument have some sections that have high
temperatures around 50 ℃or more in room temperature for a while
during supplying power or shutting off power supply (”MOD301”,
“U301”, “TR1, TR3 and radiator” indicated on the Fig. in the next
page.) , so care should be taken not to touch them. If neglected, it
may cause unexpected burns on your skin.
Warning ●The battery is installed on the P.C. board of the instrument, so care
should be taken not to short between the polarities of batteries
unnecessary. If neglected, there may cause remarkable deterioration
of the battery life, damage in the instrument or electric shock to the
operator.
VIII
Battery
U301
MOD301
Warning ●Don’t supply the power when the instrument is placed directly on the
conductive material such as metal, and also when it is covered in
conductive bag for packaging. If neglected, it may cause the damage
in the instrument or electric shock to the operator.
CN202
DIP202 DIP203
Tabla de contenidos
Otros manuales de Panel táctil de Minebea
Manuales populares de Panel táctil de otras marcas
IBASE Technology
IBASE Technology ASTUT-152-RE1S Manual de usuario
YASKAWA
YASKAWA TP 610C Manual de usuario
B&R
B&R Power Panel C Series Manual de usuario
Beijer Electronics
Beijer Electronics X2 control Manual de usuario
AXIOMTEK
AXIOMTEK GOT321W-521 Manual de usuario
TRIDONIC.ATCO
TRIDONIC.ATCO x-touchBOX Manual de usuario
