MIMAKI JFX500-2131 Manual de usuario
For Service Engineers
Revision 1.1
Vacuum Unit (OPT-J0330)
Installatioin Guide
D901827-11
MIMAKI ENGINEERING CO., LTD.
URL:http://eng.mimaki.co.jp/
Contents
Safety Precautions.................................................................3
Parts list.................................................................................4
Work procedures ...................................................................5
Changing vacuum control unit parameter..............................9
2
About this Manual
This manual for service engineers provides the necessary setup information for adding a vacuum
cable to the flatbed UV inkjet printer JFX500-2131. When performing maintenance work, refer to this
manual and the following related documents for details on working procedures.
Documents Related to this Device
Documents other than this manual that describe the JFX500-2131 are listed below. Refer to this
documents as necessary.
• Operation Manual (included with the device)
• Mechanical Drawing
• Maintenance Manual
3
Safety Precautions
Warning signs
The meanings of the warning signs used in this manual are described below. Make sure you fully
understand the meaning of these warnings before beginning work.
Caution
Sign Title Meaning
Danger sign Indicates that there is a risk of death or serious injury if the
directions are ignored or the device is not handled correctly.
Warning sign Indicates that there is a risk of injury or that physical damage
may occur if the directions are ignored or the device is not
handled correctly.
Important sign Describes important information in regards to carrying out the
setup work. Make sure you understand this information before
beginning work.
Hint sign Describes useful information for performing setup work.
(P.1-10) Reference page Gives the page number of pages that contain related informa-
tion.
Check the reference page for additional information.
Before attaching work, be sure to turn off the main power of the main body and
pull out power wire.
When performing the work, fully be careful about the edge etc. of the sheet metal
and not to get injured.
When discarding packaging materials and unnecessary parts, be sure to obey the
laws and the rules of the relevant country and the region.
4
Parts list
Part
Name Cable
(with hexagonal locking screw) Part
Name Cable clamp Part
Name Banding band
Quantity 1 Quantity 4 Quantity 2
Remark Remark Remark
Part
Name Tiflex hose Part
Name Hose clamp Part
Name Cuff
Quantity 1 Quantity 1 Quantity 1
Remark Remark Remark
This option consists of the vacuum unit and the connection parts.
Use it together with the other option below:
Vacuum unit
Extension between printer device and vacuum unit
Extension of power wire of vacuum unit
Check
Check
Check
Check
Check
Check
5
Work procedures
1. Turn off the power supply.
(1) Move the Y bar to the waiting position
(rear of main body).
(2) Turn off the sub power switch of the oper-
ation panel.
(3) Turn off the main power switch on the
side of the main body.
(4) Pull out power wire.
2. Remove the covers.
(1) Remove the cover A and B (A: power
supply front cover, B: BOX cover).
(2) Remove the connector cover near the
vacuum valve.
3. Fix the Dsub connecter.
(1) Remove the screw and the vacuum unit
fixing plate.
A
B
6
(2) Fix attached cable on the vacuum unit fix-
ing plate with the hexagonal locking
screw.
(3) Push the cable edge of the opposite side
into the hole.
(4) Fix the vacuum unit fixing plate on the
original position with the screw.
4. Perform wiring under the table.
(1) Perform wiring on the bottom plate.
•Add the attached clamp.
Push it into this hole.
Vacuum unit fixing
place
7
Work procedures
(2) Pass it through the rear hole of the bear-
ing BOX and the side hole of the power
supply rear cover (middle one of the three
holes).
(3) Fix it with the existing clamp inside the
power supply BOX.
(4) Connect it with CN14 and CN15 of the
big/ small feeding and taking-up PCB.
5. Perform wiring under the table.
(1) Loosen the hose clamp at the outlet of the
collecting tube and separate the hose
from the collecting tube.
(2) Attach the cuff to the attached hose and
fix it on the outlet of the collecting tube.
•Reuse the hose clamp.
8
(3) Fix the original hose with the banding
band as required. Put the hose newly
attached out of the machine from beneath
the bottom plate so that it may not contact
with the X bearing.
6. Perform wiring/ piping of the vacuum unit side.
(1) Connect the connector.
•Cable between the printer main body
and the vacuum is not included in this
vacuum option.
•For installation of the vacuum unit,
refer to the manuals below separately:
OPT-J0220 D500492
OPT-J0217/OPT-J0216 D500484
(2) Tighten the hose clamp and connect the
hose.
7. Change the setting of the inverter.
•Refer to P.9 “Changing vacuum control unit parameter”.
Put the hose newly attached here out of the
machine from beneath the bottom plate.
9
Changing vacuum control unit parameter
It is necessary to change the parameter of the vacuum control unit.
1. Remove the screws (for four positions)
and the control unit cover.
2. Disable the data protection function of the inverter.
(1) Enter into the function code data screen of the function code “F00”.
(2) By pressing [STOP] + [] or [STOP] + [], change the function code data of F00 from
“1” to “0”.
Menu
Function code
Operation mode
Function code data
Operation procedures
Operation mode
Program mode
[PROG/ RESET] key
[FUNC/ DATA] key
Display example 1
“1.F--” “1.E--” “1.C--” ---
(Display is changed with []/[])
Display example 2
“F00” “F01” --- “E01” “E02” --- “C01” “C02” ---
(Display is changed with []/[])
Display example 3
“1” (for F01)
(Display is changed with []/[])
With the data
fixed, go to the
function code.
Without the data
fixed, go to the
function code.
10
3. Change the setting of the function code data.
•Change three function codes below according to the table below:
•C05, C06 and C07 are assigned to the inverter frequency setting of “WEAK”, “STAN-
DARD” and “STRONG” respectively.
•This frequency can be set in the range of 8Hz to 16Hz arbitrarily.
•For your reference, the absorption level and the static pressure value (actual measured
value) are indicated below. The one to be set in this option is indicated in the gray line.
Function code Name Setting before shipment Changed example
C05 Multistage frequency 1 15.00 20.00
C06 Multistage frequency 2 10.00 40.00
C07 Multistage frequency 3 6.00 60.00
•Do not change the function code data other than the target.
•When you changed the function code data other than the ones in the table above
and when you cannot figure it out, perform initialization of the function code data
by changing the function code data of the function code “H03” to “1” once.
Then, all are reset to the change value in the "Function code parameter" table of
the following page.
•Change “H03” with [STOP] key + [] or [STOP] key + []. After initialization has
been completed, it returns to “0” automatically.
Absorption level display of JFX16 series option vacuum and static pressure value
• When using OPT-J0216
Absorption level display of JFX500 built-in vacuum and static pressure value
Absorption level display of JFX500 option vacuum and static pressure value
• When the inverter setting is C05=20, C06=40 and C07=60
• You can also change C05, C06 and C07 arbitrarily.
Example) When you set the strength corresponding to the JFX16 series
absorption level 6 to “STANDARD”, set “C06=35”.
• When using OPT-J0216
Correspondence table of absorption level and frequency set for C05/ C06/ C07
JFX16 series absorption level Frequency set for C05/ C06/ C07
112Hz
215Hz
320Hz
425Hz
530Hz
635Hz
740Hz
845Hz
950Hz
10 60Hz
Static pressure in all-closed status
WEAK
STANDARD
STRONG
WEAK
STANDARD
STRONG
Otros manuales para JFX500-2131
6
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Impresora de MIMAKI
MIMAKI
MIMAKI JV5-320DS Manual de usuario
MIMAKI
MIMAKI UCJV300 Manual de mantenimiento
MIMAKI
MIMAKI UJF-3042MkII e Manual de mantenimiento
MIMAKI
MIMAKI UCJV300 Manual de usuario
MIMAKI
MIMAKI CJV300-130 Manual de usuario
MIMAKI
MIMAKI JFX500-2131 Instrucciones de instalación
MIMAKI
MIMAKI JV33-130 Manual de usuario
MIMAKI
MIMAKI JV330 Series Manual de usuario
MIMAKI
MIMAKI JV400-SUV-160 Manual de usuario
MIMAKI
MIMAKI Tx400-1800B series Manual de usuario
MIMAKI
MIMAKI TS300P-1800 Manual de mantenimiento
MIMAKI
MIMAKI JV3 Series Manual de usuario
MIMAKI
MIMAKI JV34-260 Manual de usuario
MIMAKI
MIMAKI SWJ-320EA Manual de mantenimiento
MIMAKI
MIMAKI UJF-3042MkII EX Manual de usuario
MIMAKI
MIMAKI UJV-160 Manual de usuario
MIMAKI
MIMAKI SWJ-320 S2 Manual de usuario
MIMAKI
MIMAKI JV300-130 A Manual de usuario
MIMAKI
MIMAKI JFX500-2131 Guía de referencia
MIMAKI
MIMAKI JV400-LX Manual de usuario
