Milnor Mark II Manual de instrucciones

Published Manual Number/ECN: MAUPNOPRAU/95093N

• Publishing System: TPAS

• Access date: 04/13/2000

• Document ECN's: Latest Available

CE—

OPERATION - Mark II, Tilt-Two-

Way Washer-Extractor

FONCTIONNMENT - Mark II,

Laveuse-essoreuse à

renversement Avant/Arrière

BETRIEB - Mark II, Kippbare

Maschine (kippbar in beiden

Richtungen)

WERKING - Mark II, Naar beide

zijden kiepende Centrifugerende

Wasmachine

FUNZIONAMENTO - Mark II,

Lavacentrifuga Ribaltabile

in Due Direzioni

PELLERIN MILNOR CORPORATION POST OFFICE BOX 400, KENNER, LOUISIANA 70063-0400, U.S.A.

Please Read

About the Manual Identifying Information on the Cover

The front cover displays pertinent identifying information for this manual. Most important, are

the published manual number (part number) /ECN (date code). Generally, when a replacement

manual is furnished, it will have the same published manual number, but the latest available

ECN. This provides the user with the latest information applicable to his machine. Similarly all

documents comprising the manual will be the latest available as of the date the manual was

printed, even though older ECN dates for those documents may be listed in the table of

contents.

When communicating with the Milnor factory regarding this manual, please also provide the

other identifying information shown on the cover, including the publishing system, access date,

and whether the document ECN’s are the latest available or exact.

References to Yellow Troubleshooting Pages

This manual may contain references to “yellow pages.” Although the pages containing

troubleshooting procedures are no longer printed on yellow paper, troubleshooting instructions, if

any, will be contained in the easily located “Troubleshooting” chapter or section. See the table of

contents.

Trademarks of Pellerin Milnor Corporation

The following, some of which may be used in this manual, are trademarks of Pellerin Milnor

Corporation:

Ampsaver®CBW®Gear Guardian®Milnet®Staph-Guard®

Autolint®Dye-Extractor®Hands-Off®Milnor®System 4®

Auto-Purge®Dyextractor®Hydro-Cushion®Miltrac System 7®

Autovac E-P Plus®Mildata®Miltron Totaltrol®

Comments and Suggestions

Help us to improve this manual by sending your comments to:

Pellerin Milnor Corporation

Attn: Technical Publications

P. O. Box 400

Kenner, LA 70063-0400

Fax: (504) 469-1849

Table of Contents

for MAUPNOPRAU/95093N

OPERATION - Mark II, Tilt-Two-Way Washer-Extractor

Page Description Document/ECN

1 Section 1: English

2 Description of Controls - Mark II, Tilt-Two-Way

Washer-Extractor MSOUPNCTAE/9433AV

6 Normal Operation - Mark II, Tilt-Two-Way Washer-

Extractor MSOUPNNOAE/9433AV

13 Correcting Errors - Mark II Washer-Extractor MSOUPUTSAE/9436AV

17 Section 2: Français

18 Description des Commandes - Mark II, Laveuse-

essoreuse à renversement Avant/Arrière MSOUPNCTAF/9433AV

22 Fonctionnement courant - Mark II, Laveuse-essoreuse

à renversement Avant/Arrière MSOUPNNOAF/9433AV

29 Correction des Erreurs - Mark II Laveuse-essoreuse MSOUPUTSAF/9436AV

33 Section 3: Deutsch

34 Beschreibung der Steuerung - Mark II, Kippbare

Maschine (kippbar in beiden Richtungen) MSOUPNCTAG/9433AV

38 Normalbetrieb - Mark II, Kippbare Maschine (kippbar

in beiden Richtungen) MSOUPNNOAG/9433AV

45 Fehlerbehebung - Mark II, Wasch-Schleuder-Maschine MSOUPUTSAG/9436AV

49 Section 4: Nederlands

50 Beschrijving van de Besturing - Mark II, Naar

beide zijden kipende Centrifugerende Wasmachine MSOUPNCTAH/9433AV

54 Normale werking - Mark II, Naar beide zijden

kiepende Centrifugerende Wasmachine MSOUPNNOAH/9433AV

61 Oplossen Storingen - Mark II Centrifugerende

Wasmachine MSOUPUTSAH/9436AV

65 Section 5: Italiano

66 Descrizione dei Controlli - Mark II, Lavacentrifuga

Ribaltabile In Due Direzioni MSOUPNCTAI/9433AV

70 Funzionamento Normale - Mark II, Lavacentrifuga

Ribaltabile In Due Direzioni MSOUPNNOAI/9433AV

77 Correzione Errori - Mark II Lavacentrifuga MSOUPUTSAI/9436AV

Section 1

English

MSOUPNCTAE/9433AV

Description of Controls

Mark II, Tilt-Two-Way

Washer-Extractor

m/M Master switch

Thisswitchcontrolssingle-phasecontrolcircuit

power to the machine and the DC power supply

for the microprocessor and its components.

Setting this switch to mduring operation stops

the machine.

aOperator Signal

Thissignalis activated whenoperatorattentionis required,aswhenunloadingisrequired

or certain errors occur. Pressing Acancels the signal.

ASignal Cancel button

This button extinguishes the operator signal (a). If the signal was programmed as part

of a formula, the formula resumes after this button is pressed. If an error caused ato

illuminate, pressing Aafter correcting the error will extinguish the signal. If awas

illuminated when a valid formula was selected, the signal will terminate automatically

when the formula is started or the door is opened.

R/P Run/Program keyswitch

Setting the keyswitch to Rprevents programmed data from being changed and allows

normal machine operation. Setting the keyswitch to Pallows programming machine

operation and certain troubleshooting procedures.

No symbol Emergency Stop button

Thislargeredbuttoninayellowrectanglemayappearinseverallocationsonthemachine.

It performs the same function as 0, but locks in the depressed position and must be

turned to release the button and close the circuit before operation can resume.

0Stop button

This button stops the machine immediately by opening the three-wire circuit. Emergency

Stop buttons perform the same function. Pull cords and kick plates, if the machine has

them, also perform the same function.

1Start button

This button starts a cycle or resumes an interrupted cycle if a formula is selected and

certain safety considerations are met.

It is also used with other controls listed in this section.

lDoor Open button

This button retracts the door plunger to unlock the door if the machine is not running.

Pressing 1+l jogs the cylinder clockwise or counter-clockwise as set by J/j.

J/j Jog switch

Thisswitchdeterminesthedirectionthecylinderwillrotatewhen jogging iscommanded.

HoldingtheswitchatJjogsclockwise;holdingtheswitchatJjogscounter-clockwise.

Description of Controls

Mark II, Tilt-Two-Way Washer-Extractor MSOUPNCTAE/9433AV (2 / 4)

VBalance Sensing lightExN and

balancing Hydro-Cushion®models

This light is extinguished while the

imbalance exceeds preset limits.

X/Y/ZBalance Valve lightsbalancing

models

These lights show which balancing valves

are open. They are extinguished when

balancing is complete, except for intermittent operation as the balancing system

compensates for changes in the imbalance. Lights that stay on through most extractions

may indicate inadequate water supply to the balancing system or that the balancing

system requires service.

Service is required if all three lights illuminate at the same time.

H/W Manual Flush/Spray switchmachines

with five-compartment supply injectors

Hold this switch to Hto flush water into the first

compartment of the supply injector. Hold this

switch to Wto use the spray nozzle to clean the

supply injector.

fManifold Flush button

Press this button to flush the chemical supply

manifold with fresh water.

B/dAlternate Drain switch

Set this switch to dto disable all machine

functions and hold the drain closed. The machine

can be powered off with the drain closed for

overnight soaking. Set to Bto permit normal

operation.

_/- Mildata Remote/Local switchMildata option

Set this switch to -to have the machine communicate with the Mildata computer. Set

to _to use internal machine formulas.

E/e Ampsaver switchAmpsaver option

Ecauses the Ampsaver controller to delay extraction when necessary to prevent the

amperage drawn by all machines from exceeding a preset maximum. eprevents the

Ampsaver controller from affecting machine operation.

Description of Controls

Mark II, Tilt-Two-Way Washer-Extractor MSOUPNCTAE/9433AV (3 / 4)

f/g Up/Down Tilt switchExN models

Hold g+1 to tilt the cylinder for loading or to return to the normal position after

unloading. Hold f+1 to tilt the cylinder for unloading or to return to the normal

position after loading.

U/u Rear/Front Tilt switchQTN, WTN, and BTN models

This switch selects whether the front (U) or rear (u) of the machine moves when the

machine tilts.

T/r Up/Down Tilt switchQTx, WTx, and BTx models

To tilt the machine, set U/u for the desired tilting direction, then hold T+1. Hold

r+1 to return the cylinder to the normal position.

D/d Hydraulic Door switchModels with motorized doors

Pressing D+l closes the door if a formula is not running. d+l opens the door if

a formula is not running.

Description of Controls

Mark II, Tilt-Two-Way Washer-Extractor MSOUPNCTAE/9433AV (4 / 4)

<B>D?==>04(#""0E

>_b]Q\?`UbQdY_^±=Qb[99

DY\dDg_GQiGQcXUb5hdbQSd_b

CdQbddXU?`UbQdY^W4Qi

2UCQVUComply with all safety instructions in this manual and on this machine.

FUbYViCgYdSX@_cYdY_^c

Switch Symbol Selection Switch Setting by Name/Function

< 

Set the Run/Program keyswitch to run.

5^UbWYjU=YSb_`b_SUcc_b3_^db_\\Ub Set the Master switch to on (). The operator

signal sounds and a series of displays appear.



®®

Machine is ready for a load.

®®®® Machine is on-line to Mildata and ready for a load. See “Enter Cake Data

If Machine On-Line to Mildata.”

Otros manuales para Mark II

Tabla de contenidos

Idiomas:

Otros manuales de Arandela de Milnor

Milnor

Milnor 48032BTL Manual de instalación y funcionamiento

Milnor

Milnor 30022 Manual de usuario

Milnor

Milnor 36026X8J Manual de funcionamiento

Milnor

Milnor MCT12E5 Manual

Milnor

Milnor 30 Series Manual de funcionamiento

Milnor

Milnor 30015T6X Manual de usuario

Milnor

Milnor 60044WP3 Manual de usuario

Milnor

Milnor 30022X8W Manual de usuario

Milnor

Milnor 72044 WP3 Manual de usuario

Milnor

Milnor MWR/T12X5 Manual de usuario

Milnor

Milnor 60044SR2 Manual

Milnor

Milnor BICWUT01 Instrucciones de funcionamiento

Milnor

Milnor MWF27J8 Manual

Milnor

Milnor C4A Manual

Milnor

Milnor 30022V8Z Manual de usuario

Milnor

Milnor 36 Series Manual de funcionamiento

Milnor

Milnor 36021 Manual de funcionamiento

Milnor

Milnor 48040F7 Series Manual

Milnor

Milnor 30022H7J Manual de instalación y funcionamiento

Milnor

Milnor MWR09E5 Series Guía

Milnor

Milnor MilTouch MWF36Z8 Manual

Milnor

Milnor MCT27E5 Manual

Milnor

Milnor 30022H7x Instrucciones de montaje

Milnor

Milnor 76028 G3 CBW Manual

Manuales populares de Arandela de otras marcas

Tricity Bendix

Tricity Bendix AW 1000 W Guía del producto

Panasonic

Panasonic NA-F60L5WRB Manual de usuario

GE WSLP1500 Manual

Electrolux

Electrolux EWF1284EDW Manual de usuario

Bosch

Bosch WAN2829BSN Manual de usuario

LG TV2516DV3B Manual de usuario

LG TH2517DSAV Manual de usuario

VESTEL

VESTEL CMH-XL 7510 TE Manual de usuario

AEG

AEG 74335 Manual de operación

Johnson

Johnson JWF721A Manual de usuario

Beko

Beko WTE7604XLW0 Manual de usuario

Danby

Danby DTT100A1WDB Instrucciones de montaje

Amica

Amica WA 14 Ex Manual de usuario

Daewoo

Daewoo DWD-F1222 Manual de usuario

Bosch

Bosch WAS28461AU Manual de usuario

Miele

Miele PW 6080 Vario Manual de usuario

Finlux

Finlux FLX108CF220 Manual de usuario

Whirlpool

Whirlpool 3LBR5132AN0 Manual de usuario