Milleteknik NEO FLX S Manual de usuario

NEO FLX S

NEO FLX 24V 5A FLX S, NEO FLX 24V 10A FLX S

351-248

Publication date 2023-02-13

Abstract

PCB: CEO3_uP

Table of Contents

1. Component overviews ................................................................................................................ 4

1.1. Component overview ....................................................................................................... 4

2. Enclosures ................................................................................................................................ 5

2.1. Bracket ........................................................................................................................... 5

2.2. Mounting on a wall or in a 19 "rack ................................................................................... 5

2.3. Mounting ........................................................................................................................ 6

3. Batteries - placement and connection .......................................................................................... 6

3.1. Connect battery fuse / blade fuse ..................................................................................... 6

3.2. Connection of batteries in FLX S, FLX M and FLX L .......................................................... 7

4. Motherboard description ............................................................................................................. 7

4.1. Connect in this order ....................................................................................................... 7

4.2. Connect alarm on P3 ....................................................................................................... 8

4.3. Connect load .................................................................................................................. 9

4.4. Connect mains ................................................................................................................ 9

4.5. Control alarm limit ......................................................................................................... 10

4.6. Fuses ........................................................................................................................... 10

5. Commissioning - how to start the unit ........................................................................................ 10

6. Alarm displayed on cabinet door ............................................................................................... 11

7. NEO Product Sheet .................................................................................................................. 11

7.1. NEO Battery backup with more alarm functions ............................................................... 11

7.1.1. NEO - Name, article number and e-number .......................................................... 12

7.1.2. NEO battery backup for security installations ........................................................ 12

7.1.3. Flexibility ............................................................................................................ 12

7.1.4. Area of use ........................................................................................................ 12

7.1.5. Fixed installation ................................................................................................. 12

7.2. Regulations and certifications ........................................................................................ 12

7.2.1. Requirements that the product meets .................................................................. 12

7.3. Expected operating time in the event of a power failure ( with new batteries) ..................... 13

7.4. Circuit boards - Technical data ....................................................................................... 13

7.4.1. Technical data: CEO 3 ........................................................................................ 13

Control alarm limit with JU2 .................................................................................. 13

Control alarm limit ........................................................................................ 13

Fuses ................................................................................................................. 13

7.5. Power supply ................................................................................................................ 14

7.5.1. Power supply - Technical Data LRS-150-24 .......................................................... 14

7.5.2. Power supply - Technical Data RSP-320-24 ......................................................... 14

7.6. Technical data enclosures .............................................................................................. 15

7.6.1. Enclosures - Technical Data FLX S ...................................................................... 15

7.7. Link to the latest information .......................................................................................... 15

7.8. Warranty, support, country of manufacture and country of origin ....................................... 15

7.8.1. Warranty ............................................................................................................ 15

7.8.2. Support .............................................................................................................. 16

Spare parts ......................................................................................................... 16

Questions about product performance? ................................................................. 16

7.8.3. Contact us ......................................................................................................... 16

7.8.4. Country of manufacture ....................................................................................... 16

7.8.5. Designed and produced by: Milleteknik AB ........................................................... 16

7.9. Batteries - recommended, not included ........................................................................... 16

7.9.1. Batteries are not included they are sold separately ............................................... 16

7.9.2. 14 Ah, 12 V AGM battery .................................................................................... 16

8. Address and contact details ...................................................................................................... 17

READ THIS FIRST!

If possible, leave 100 mm of free space.

The system is intended for use in a controlled indoor environment.

Only authorized persons should install and maintain the system.

It is the installer's responsibility to ensure that the system is suitable for its intended

use.

Documents accompanying the system must be kept in or in its immediate vicinity.

Ventilation should not be covered. Mains voltage should be disconnected during instal-

lation.

All information subject to change.

Upon installation of this product, the installer acknowledges and accepts the limitations

of this product as described in this manual.

1. COMPONENT OVERVIEWS

1.1. Component overview

Table 1. Component overview

Number Explanation

A Cabinet in black powder-coated sheet metal.

B The power supply, location and type vary with configuration.

C Motherboard.

D Cable entries.

E Batteries.

2. ENCLOSURES

2.1. Bracket

Brackets are used so that the unit can be mounted on a wall or in a 19 "rack.

Nr Explanation

1 Clip in bracket that secures the bracket to the housing.

2 Holes for screws - can be used to secure the bracket in the housing.

3 The brackets is screwed to a wall or 19 "rack.

2.2. Mounting on a wall or in a 19 "rack

The unit can be mounted in a 19" rack or on a wall. The supplied brackets can be attached in two ways:

When mounting on a wall, the brackets must sit backwards, against the wall. When mounting in a 19"

rack, the console must be attached at the front of the unit.

Figure 1. FLX S - mount brackets

Left bracket facing the front for mounting in a 19 "rack.

Right bracket facing the back for wall mounting.

IMPORTANT

Leave 100 mm free around the air vents.

2.3. Mounting

Use the appropriate screw for mounting on a wall or in a 19" rack. Screws for mounting on a wall or in a

rack are not included.

3. BATTERIES - PLACEMENT AND CONNECTION

3.1. Connect battery fuse / blade fuse

Figure 2. Fuse holders with blade fuses are connected to + and minus on batteries

3.2. Connection of batteries in FLX S, FLX M and FLX L

Battery wiring is mounted on the circuit board upon delivery. Pictures below only show how to connect

wiring.

1. Place the batteries in the cabinet with the battery terminals facing outwards.

2. Connect the battery cable. Red cable on + and black cable on -.

• If possible, disconnect mains voltage when replacing the battery.

Figure 3. Wiring diagram for batteries in battery backup

Connect the terminals correctly so that you do not damage the equipment.

4. MOTHERBOARD DESCRIPTION

4.1. Connect in this order

To minimize the risk of errors that may occur in connection with a short circuit, connections to the

motherboard must be made in this order.

Table 2. Connect in this order

Nr Explanation

1 Connect alarm.

2 Connect load.

3 Connect batteries

4 Connect mains.

Figure 4. Description: CEO3 uP

On PCB Explanation

D6 Indicator diode.

JU2 Jumper for alarm control.

P1:1-3 Mains connection.

P2:1-2 Load output, + / -.

P2:3-4 Load output, + / -.

P3:1-3 Alarm output, NC, CO, NO.

P3:4-6 Alarm output, NC, CO, NO.

4.2. Connect alarm on P3

Alarm is connected to terminal P3

Table 3. Connect alarm P3

P3:1-6 Explanation

Sum alarm

P3:1 NC

P3:2 Com

P3:3 NO

P3:4 NC

P3:5 Com

P3:6 NO

4.3. Connect load

Table 4. Load connections

Circuit board number Explanation

P2: 1 Connection for load 1 +

P2: 2 Connection for load 1 -

P2: 3 Connection for load 2 +.

P2: 4 Connection for load 2 -.

MAX CURRENT

Maximum current must not be exceeded. Maximum current is indicated on the CE-

marking on the unit.

DANGER

Mains must be disconnected when working with bare wires.

4.4. Connect mains

Pull wiring through the cable entry on the cabinet.

If possible, secure the mains cable with cable ties where possible.

Electrical network cabling shall be kept separate from other cabling to avoid EMC interference.

Figure 5. Connect the mains to the motherboard

Connect the mains cable to the terminal before it is put back on the motherboard. Secure F and N with

cable ties for electrical safety.

Table 5. Electrical network connections

Letter Explanation

F Phase

N Neutral

PE Protective earth

ELECTRICAL MAINS CONNECTION 230 V AC ON CIRCUIT

BOARD

Check that the marking on the circuit board matches the cable arrangement on the

terminal block.

4.5. Control alarm limit

Alarm for low battery voltage in battery operation can be controlled.

By jumpering JU2, the limit for when the unit should give an alarm can be lowered.

Alarms are given when the battery voltage in battery drops below the limit.

Table 6. Alarm limits

Alarm limit at low battery voltage 12 V 24 V

JU2 with jumper* 10.2 V 24.0 V

JU2 without jumper * 13.2 V 26.5 V

*The unit is delivered with jumper on JU2

4.6. Fuses

Unit Fuse Type Explanation

All units F1 T2,5A Mains fuse

F2, F6 T5A Load fuse +

F2, F6 T10A Load fuse +

All units F7 T16A Battery fuse

FUSE REPLACEMENT WARNING (A)

There is a risk of damage if the fuse is changed to a larger one than what the unit

is delivered with. The function of the fuse is to protect the connected load and cables

against damage and fire. It is not possible to change the fuse to a larger one to

increase the power output.

5. COMMISSIONING - HOW TO START THE UNIT

The unit works normally when the indicator LED on the outside of the cabinet door lights up with a solid

green light. See front panel for other status indications.

It may take up to 72 hours before the batteries are fully charged.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Paquete de baterías de milleteknik

milleteknik

milleteknik NEO 24V 15A-25A FLX L PRO1 Manual de usuario

Manuales populares de Paquete de baterías de otras marcas

Acumentrics

Acumentrics PACK-POWER SYSTEM Manual de usuario

ACDC Dynamics

ACDC Dynamics SPF12-50 Manual de usuario

Aegis

Aegis ABL-72020P Manual de usuario

Dyness

Dyness TowerESS Manual de usuario

Growatt

Growatt APX 5.0P-S0-US Manual de usuario

EGO

EGO BAX1300 Manual de usuario

CyberPower

CyberPower BCA Series Manual de usuario

Intermec

Intermec 700 Series Manual de usuario

Dometic

Dometic PLB40 Manual de usuario

V-TAC

V-TAC VT-48280-W2 Manual de usuario

Valence

Valence RT Manual de usuario

Nikon

Nikon MB-D14 Manual de usuario

IOGear

IOGear GBP24V Series Manual de usuario

Inventus Power

Inventus Power PROTRXion S-12V100-TRX-HD Manual de usuario

Clas Ohlson

Clas Ohlson PW-290A Manual de usuario

EINHELL

EINHELL MULTI-Ah Power X-Change Plus Manual de usuario

Samsung

Samsung EB-U3300 Manual de usuario

ECTIVE

ECTIVE LC Series Manual de usuario

milleteknik NEO FLX S Manual de usuario

Manuales populares de Paquete de baterías de otras marcas