Miller Dynasty 280 DX Manual de usuario

OWNER’S MANUAL

OM-267 827A 2014−04

Dynasty280 DX

AC Independent Expansion

Read and follow the power source Owner’s Manual and labels carefully before installing, operating, or servicing unit.

Read the safety information at the beginning of the manual and in each section.

1-1. Software Expansion

Card Requirements:

.Purchased software expansion

memory card required.

1Memory Card Port

2Indicator LED

Enabling Software Expansion:

Insert card containing software expan-

sion into port.

LED indicator blinks green while ma-

chine is reading from or writing to the

card. After successfully reading from or

writing to the card, the LED switches

from blinking green to continuous

green. The machine is now ready to use

software expansion. Do not remove

card while LED is blinking green.

.Software expansion card must re-

main in memory card port to enable

software expansion.

Disabling Software Expansion:

Remove the software expansion card

from the memory card port.

Troubleshooting:

Problem: Indicator LED is continuous

red.

Remedy: Remove and reinsert card. If

problem continues, the card is bad.

Contact Factory Authorized Service

Center for a replacement card.

The memory card port uses an SD

memory card.

SD Logo is a trademark of the 3C

Company.

1-2. AC Independent Amplitude (Dynasty DX Models Only)

1 AC Waveshape Control

Press switch pad until desired function is se-

lected.

2 Encoder Control (Set Value)

3 Ammeter (Displays Value)

4 Voltmeter (Parameter Selection)

EN Amperage [EN] - Use with AC TIG only to

select electrode negative amperage value.

EP Amperage [EP] - Use with AC TIG only to

select electrode positive amperage value.

.Both Balance and AC Frequency LEDs

lightwhen either EN or EP Amperage is se-

lected.

5 AmperageControl

Average Amperage Control: Setting EN Am-

perage, EP Amperage, Balance, and Frequen-

cy values creates an average amperage. The

operator can change the average amperage

value while maintaining the same EN amper-

age to EP amperage ratio at the existing bal-

ance and frequency. To change the average

amperagevalue, press the Amperage switch

pad and turn the Encoder control. The chang-

ing average value is displayed on the ammeter.

Example:If EN Amperage is 150, EP Amper-

age is 100, Balance is 75%, and Frequency is

120,the average amperage is 138 amps. If you

press the Amperage switch pad and turn the

Encodercontrol until 69 amps is displayed, the

EN amperage is now 75 and EP amperage is

now 50. The balance remains 75%, and the fre-

quency is still 120, and the 1.5 to 1 EN amper-

age to EP amperage ratio is maintained.

150 A

1-3. AC Independent Waveshape (Dynasty DX Models Only)

.See Dynasty 280 DX Operation section in

Owner’s Manual 253086 for additional in-

formationon Accessing User Setup Menu.

The [ACEN], [ACEP] option replaces the

[AC] option.

1 Amperage Control

2 Parameter Display

Press switch pad until desired waveshape

[ACEN] or [ACEP] is displayed.

3 Setting Display

4 Encoder Control

Use Encoder to select between advanced

squarewave [ADVS], soft squarewave

[SOFT], sine wave [SINE], or triangle wave

[TRI]. The default is [SOFT].

234

USER

SOFT

ACEN

ACEP

Tabla de contenidos

Otros manuales de Sistema de soldadura de Miller

Miller

Miller Axcess E 300 Manual de usuario

Miller

Miller Big Blue 600 Pro Manual de usuario

Miller

Miller Maxstar 200 Manual de usuario

Miller

Miller XR-D Control Manual de usuario

Miller

Miller XRW Manual de usuario

Miller

Miller SUBARC WIRE DRIVE 400 T CE Manual de usuario

Miller

Miller XMT 304 Manual de usuario

Miller

Miller Axcess 300 Manual de usuario

Miller

Miller XPS 350 Manual de usuario

Miller

Miller BOC Migmatic 250 Manual de usuario

Miller

Miller ARC PAK 350 Manual de usuario

Miller

Miller ST-24w Manual de usuario

Miller

Miller Trailblazer 300D NT Manual de usuario

Miller

Miller Axcess 300 Manual de usuario

Miller

Miller Millermatic 350P Manual de usuario

Miller

Miller Millermatic 210 Manual de usuario

Miller

Miller PipeWorx 350 FieldPro Manual de usuario

Miller

Miller DIVERSION 165 Manual de usuario

Miller

Miller Regency 250 Manual de usuario

Miller

Miller TRAILPOWER 5GA1 Manual de usuario

Miller

Miller MILLERMATIC 70A Manual de usuario

Miller

Miller Dynasty 280 Manual de usuario

Miller

Miller Syncrowave 500 Manual de usuario

Miller

Miller Millermatic 252 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario