Miller Dynasty 210 DX Manual de usuario

OWNER’S MANUAL

OM-267 827C 2015−05

Dynasty210 DX and 280 DX

AC Independent Expansion

Read and follow the power source Owner’s Manual and labels carefully before installing, operating, or servicing unit.

Read the safety information at the beginning of the manual and in each section.

1-1. Software Expansion

.A software update is required to ensure proper

operation of all purchased feature expan-

sions. For instructions to download TIG Soft-

ware updates, see PDF file F269272A on soft-

ware expansion memory card.

Card Requirements:

.Purchased software expansion memory card

required.

1 Memory Card Port

2 Indicator LED

Enabling Software Expansion:

Insert card containing software expansion into

port.

LED indicator blinks green while machine is read-

ing from or writing to the card. After successfully

readingfrom or writing to the card, the LED switch-

es from blinking green to continuous green. The

machineis now ready to use software expansion.

Do not remove card while LED is blinking green.

.Software expansion card must remain in memory

card port to enable software expansion.

Disabling Software Expansion:

Remove the software expansion card from the

memorycard port.

Troubleshooting:

Problem: Indicator LED is continuous red.

Remedy: Remove and reinsert card. If problem

continues,the card is bad. Contact Factory Autho-

rized Service Center for a replacement card.

The memory card port uses an SD memory card.

The SD Logo is a trademark of the SD-3C LLC

Company.

OM−267 827 Page 2

1-2. AC Independent Amplitude (Dynasty DX Models Only)

1 AC Waveshape Control

Press switch pad until desired function is select-

ed.

2 Encoder Control (Set Value)

3 Ammeter (Displays Value)

4 Voltmeter (Parameter Selection)

EN Amperage [EN] -Use with AC TIG only to se-

lect electrode negative amperage value.

EP Amperage [EP] -Use with AC TIG only to se-

lect electrode positive amperage value.

.Both Balance and AC Frequency LEDs light

wheneither EN or EP Amperage is selected.

5 AmperageControl

Average Amperage Control: Setting EN Am-

perage,EP Amperage, Balance, and Frequency

values creates an average amperage. The oper-

ator can change the average amperage value

whilemaintaining the same EN amperage to EP

amperageratio at the existing balance and fre-

quency. To change the average amperage value,

press the Amperage switch pad and turn the En-

coder control. The changing average value is dis-

playedon the ammeter. Example: If EN Amper-

age is 150, EP Amperage is 100, Balance is 75%,

and Frequency is 120, the average amperage is

138 amps. If you press the Amperage switch pad

and turn the Encoder control until 69 amps is dis-

played,the EN amperage is now 75 and EP am-

perageisnow 50. The balance remains 75%, and

the frequency is still 120, and the 1.5 to 1 EN am-

perageto EP amperage ratio is maintained.

150 A

1-3. AC Independent Waveshape (Dynasty DX Models Only)

.See Dynasty 210 DX and 280 DX Opera-

tion section in Owner’s Manual for addi-

tionalinformation on Accessing User Set-

up Menu. The [ACEN], [ACEP] option re-

places the [AC] option.

1 Amperage (A) Control

2 Gas/DIG Control

3 Parameter Display

Press Gas/DIG control until [ACEN] is dis-

played.Press the Amperage (A) control to tog-

gle between [ACEN] and [ACEP].

4 Setting Display

5 Encoder Control

Use Encoder to select between advanced

squarewave [ADVS], soft squarewave

[SOFT], sine wave [SINE], or triangle wave

[TRI]. The default is [SOFT].

345

USER

SOFT

ACEN

ACEP

Otros manuales para Dynasty 210 DX

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de soldadura de Miller

Miller

Miller SuitCase X-TREME 8VS CE Manual de usuario

Miller

Miller Passport 180 Manual de usuario

Miller

Miller Dynasty 210 Manual de usuario

Miller

Miller MTXC 3501M Robot Gun Manual de usuario

Miller

Miller XMT 425 CC/CV Manual de usuario

Miller

Miller Millermatic 255 Manual de usuario

Miller

Miller Bobcat 225 NT Manual de usuario

Miller

Miller DYNASTY DX Manual de usuario

Miller

Miller S-74S Manual de usuario

Miller

Miller S-44GL Manual de usuario

Miller

Miller GA-17C Manual de usuario

Miller

Miller Blue Thunder Series Manual de usuario

Miller

Miller XR-Pistol-Plus Manual de usuario

Miller

Miller Axcess 675 Manual de usuario

Miller

Miller XMT 350 FieldPro Manual de usuario

Miller

Miller AUTO ARC TIG 50A Manual de usuario

Miller

Miller Welder Manual de usuario

Miller

Miller AMD-4G Manual de usuario

Miller

Miller MILLERMATIC 135 Manual de usuario

Miller

Miller CST 400 Manual de usuario

Miller

Miller CST 282 Manual de usuario

Miller

Miller A-500 Manual de usuario

Miller

Miller Spectrum 300 Manual de usuario

Miller

Miller Maxstar 200 Manual de usuario

Manuales populares de Sistema de soldadura de otras marcas

Berner

Berner PLASMACUT 54 Manual de usuario

Pro Spot

Pro Spot PR-155 Manual de usuario

Forney

Forney 210 Manual de usuario

Thermal Arc

Thermal Arc 400S Manual de usuario

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manual de usuario

GYS

GYS PROTIG 201 AC/DC Manual de usuario

TAFA

TAFA 30*8B35 Manual de usuario

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manual de usuario

ESAB

ESAB Buddy Arc 145 Manual de usuario

CIGWELD

CIGWELD 636804 Guía rápida

Red-D-Arc

Red-D-Arc DC-400 Manual de usuario

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manual de usuario

Elettro

Elettro HI-MIG 3000 SYNERGIC Manual de usuario

WIA

WIA Weldmatic 270 CP132-2 Manual de usuario

Sonics

Sonics H520T Manual de usuario

NewArc

NewArc RT2000 Guía de inicio rápido

Hypertherm

Hypertherm powermax1000 Manual de usuario

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manual de usuario