MiLAN MIL-C2414 Series Manual de usuario

Installation Guide: MIL-C2414

Regulatory Approvals

• FCC Class A

• UL 1950

• CSA C22.2 No. 950

• EN60950

• CE

–

EN55022

Class B

– EN50082-1

Canadian EMI Notice

This Class Adigital apparatus meets all the requirements of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur

du Canada.

European Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage

Directive (73/23/EEC) issued by the commission of the European Community. Compliance with these

directives implies conformity to the following European Norms:

• EN55022 (CISPR 22) - Radio Frequency Interference

• EN50082-1 (IEC801-2, IEC801-3, IEC801-4) - Electromagnetic Immunity

• EN60950 (IEC950) - Product Safety

Trademarks

Digi International™ and the Digi Logo are trademarks of Digi International. All other products and brands

To Contact Digi

For prompt response when calling for service information, have the following information ready:

• Product serial number and rev.

• Date of purchase

• Vendor or place of purchase

You can reach Digi LAN technical support at 408/744-2751

Or E-mail at:

[email protected]

Address:

1299 Orleans Drive

Sunnyvale, CA 94089

Voice:

408/744-2775

Fax:

408/744-2793

E-mail:

[email protected]

MIL-C2414 Series

Fast Ethernet Media Converter for Digi's

Media Conversion System

Installation Guide

This guide includes the following:

• “Introduction” on page 2

• “Installation” on page 3

• “MDI/MDI-X” on page 3

• “Link Sentry Feature” on page 5

• “Indicators” on page 6

Five-Year LimitedWarranty

Digi International warrants to the original consumer or purchaser that each of its products, and

all components thereof, will be free from defects in material and/or workmanship for a period of

ﬁve years from the original factory shipment date. Any warranty hereunder is extended to the

original consumer or purchaser and is not assignable.

Digi makes no express or implied warranties including, but not limited to, any implied warranty

of merchantability or ﬁtness for a particular purpose, except as expressly set forth in this

warranty. In no event shall Digi be liable for incidental or consequential damages, costs, or

expenses arising out of or in connection with the performance of the product delivered

hereunder. Digi will in no case cover damages arising out of the product being used in a

negligent fashion or manner.

ACT

LINK

ACT

MDI-X MDI

100BASE-TX

100BASE-FX

Thumbscrews

MIL-

C2414

MT-RJ

Installation Guide: MIL-C2414

2 7

About this Manual

This guide covers the MIL-C2414 Series Fast Ethernet,

hot-swappable media converter. The terms “MIL-

C2414,” “MIL-C2414 Series” and “converter” are used

throughout this document to describe this device.

Introduction

The MIL-C2414 is one in a series of modules designed

for Digi's Media Conversion System. This Fast Ethernet

converter supports half- and full-duplex modes. For

network budget constraint, the MIL-C2414 uses 150 ns

(approximately 30 m of cables) during conversion in

each direction.

To maximize the ﬁber cable distance, use one meter of

CAT 5 UTP cable when connecting directly to a node

(subject to ﬁber budget of 16 dBm and collision domain

restrictions). In full-duplex environments, up to 100

meters of CAT 5 UTP and for Mil-C2414 use 2 km of

62.5/125 micron multimode MT-RJ receptacle optical

ﬁber and for MIL-C2414-15 use 15 km of 10/125 micron

single-mode MT-RJ receptacle optical ﬁber

The MIL-C2414 Series comes equipped with one MT-RJ

type (100BASE-FX) connector and one RJ-45 (100BASE-

TX) connector.

Features

• Diagnostic LEDs

• Link Sentry features

1300 nm single-mode ﬁber

• 10/125 micron diameter

• Launch power: -8 dBm

• Receive sensitivity: -31 dBm

Installation Guide: MIL-C2414

6 3

Indicators

There are four LEDs, including:

•

TP/ACT

: Unit is receiving packets from the 100BASE-

TX port

•

FX/ACT

: Unit is receiving packets from the 100BASE-

FX port

•

TP/LINK

: There is an active connection on the

100BASE-TX port

•

FX/LINK

: There is an active connection on the

100BASE-FX port

Speciﬁcations

RJ-45: MDI RJ-45: MDI-X

Fiber Speciﬁcations: SC connector

1300 nm multi-mode ﬁber

• 62.5/125 micron diameter

• Launch power: -14 dBm

• Receive sensitivity: -31 dBm

• Supports half- and full-duplex modes

Installation

Do the following to install the MIL-C2414 Series into a

redundant rack mount chassis:

1. Make any conﬁguration changes to the module (i.e.,

DIP switch settings or jumper).

2. Remove the screws securing the faceplate and

remove it from the chassis.

3. Slide the module into the slot through the guide

rails.

4. Insert the module into the card-edge connector (port

bay). Make sure it is seated ﬁrmly.

5. Secure the module with the two thumbscrews

located on the faceplate of the unit.

The unit is now ready for network connections.

MDI/MDI-X Switch

The MDI/MDI-X switch allows for quick conﬁguration

of the 100BASE-TX port. Cables used when the switch is

in the MDI-X position (the “left” position):

• For a hub/repeater, use a swap cable (pins are

connected 1 to 3, 2 to 6, 3 to 1, and 6 to 2)

Pin 1=TD+

Pin 2=TD-

Pin 3=RD+

Pin 6=RD-

Pin 1=RD+

Pin 2=RD-

Pin 3=TD+

Pin 6=TD-

1234568

Installation Guide: MIL-C2414

4 5

• For a workstation/PC, use a straight-through cable

(pins are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6)

Figure 1. Inside of the MI-C2414 Series

Cables used when the switch is in the MDI position (the

“right” position):

• For a hub/repeater, use a straight-through cable

(pins are connected 1 to 1, 2 to 2, 3 to 3, and 6 to 6)

• For a workstation/PC port, use a swap cable (pins

are connected 1 to 3, 2 to 6, 3 to 1, and 6 to

2)Indicators

Link Sentry Conﬁguration

The Link Sentry feature on the MIL-C2414 Series is

conﬁgured through a 4-position DIP switch (refer to

Figure 1). Default setting for the DIP switches: All

switches are in the “up” position.

Link Sentry allows users to add new management tools

to the network. When enabled, it monitors the selected

receiver port and, if the Link test signal is not seen, the

unit will stop sending a signal through the selected

transmit port.

The following table shows which Link Sentry feature is

enabled:

Note:

For two MIL-C2414s used back-to-back and UTP-to-UTP, all DIP

switches must be

enabled

(in the “down”position) on the ﬁrst MIL-C2414.

On the second MIL-C2414, enable switches 1 and 4 (in the “down”

position).

Default setting for Link Sentry: All switches set in the “up” position

(disabled).When using the SNMP module to control the Link Sentry

feature, leave the switches in the default mode (“up”).

MDI-X/MDI

Switch

RJ-45 Female

Connector

LEDs

(4 total)

4-pin DIP Switch

MT-RJ

Connector

Table 1. Link Sentry Features

Switch Losing Link on RX of Stop sending Link onTX of

1 (down) Fiber port Fiber port

2 (down) UTP port UTP port

3 (down) UTP port Fiber port

4 (down) Fiber port UTP port

Tabla de contenidos

Otros manuales de Convertidor de medios de MiLAN

MiLAN

MiLAN MIL-GBIC-LX10 Manual de instrucciones

MiLAN

MiLAN MIL-4650 Manual de usuario

MiLAN

MiLAN MIL-1225LS Manual de usuario

MiLAN

MiLAN MIL-140 Manual de usuario

MiLAN

MiLAN MIL-225C Manual de usuario

MiLAN

MiLAN MIL-185C Manual de usuario

MiLAN

MiLAN MIL-C2412 Manual de usuario

MiLAN

MiLAN MIL-S341X Manual de usuario

MiLAN

MiLAN MIL-160T Manual de usuario

MiLAN

MiLAN MIL-C2114 Series Manual de usuario

MiLAN

MiLAN MIL-C2112 Manual de usuario

MiLAN

MiLAN MIL-9200X Manual de usuario

MiLAN

MiLAN Raven MIL-RC3112 Manual de usuario

MiLAN

MiLAN MIL-140CRM Manual de usuario

MiLAN

MiLAN MIL-C1411 Manual de usuario

MiLAN

MiLAN MIL-C1111 Manual de usuario

MiLAN

MiLAN MIL-4750 Manual de usuario

MiLAN

MiLAN MIL-100s Manual de usuario

MiLAN

MiLAN MIL-C2413 Series Manual de usuario

MiLAN

MiLAN MIL-C2000 Manual de usuario

MiLAN

MiLAN MIL-9100X Manual de usuario

MiLAN

MiLAN MIL-S3110 Manual de usuario

MiLAN

MiLAN MIL-185C Manual de usuario

MiLAN

MiLAN Raven MIL-RC6113LX Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario