MikroElektronika Click BOARD RTC 5 Manual de usuario

2 3

2. Soldering the headers

3. Plugging the board in

Once you have soldered the headers your

board is ready to be placed into the desired

mikroBUS™socket. Make sure to align the cut

in the lower-right part of the board with the

markings on the silkscreen at the mikroBUS™

socket. If all the pins are aligned

correctly, push the board all the

way into the socket.

Turn the board upward again. Make sure

to align the headers so that they are

perpendicular to the board, then solder the

pins carefully.

Turn the board upside down so that

the bottom side is facing you upwards.

Place shorter pins of the header into the

appropriate soldering pads.

Before using your click board™, make sure

to solder 1x8 male headers to both left and

right side of the board. Two 1x8 male headers

are included with the board in the package.

4. Essential features

For storing data, the chip onboard RTC5 click

has 64-bytes of battery-backed SRAM and

1 kbit of EEPROM, along with 128 bits of

protected space for storing a unique ID. The

SPI interface has clock speeds of up to 5 MHz

which is enough for a millisecond alarm. The

clock/calendar automatically compensates

for leap years and months shorter than 31

days. The interrupt pin can be used to set up

alarms or events.

RTC5 click carries MCP79510, a real-

time clock/calendar with an SPI interface

(mikroBUS™MISO, MOSI, SCK and CS pins)

and a programmable interrupt for system

output. The clock frequency is derived

from an onboard 32.768KHz oscillator.

For backup power, RTC5 click has a coin-

cell Lithium polymer battery connector.

The board is designed to use a 3.3V power

supply only.

1. Introduction

0100000085769

click

BOARD™

www.mikroe.com

RTC 5 click

RTC 5 click Manual v100

RST

SCK

MOSI

MISO

+3.3V

GND

PWM

INT

SCL

SDA

+5V

GND

BAT1C1

100nF

GND

VCC3.3

GND GND

GND

10K

10uF

GND

LD1

2K2

GND

VBAT

1X1

VBAT

VSS SI

SCK

MFP

VCC

MCP79510

32.768KHz

C92

10pF

C93

10pF

VCC3.3 VCC3.3

GND

VCC3.3

SCK

SCK MISO

MISO

MOSI

10K

VCC3.3

MFP

VCC3.3

8. Code examples

MikroElektronika oers free tech support

(www.mikroe.com/support) until the end of

the product’s lifetime, so if something goes

wrong, we’re ready and willing to help!

Once you have done all the necessary

preparations, it’s time to get your click board™

up and running. We have provided examples

for mikroC™, mikroBasic™ and mikroPascal™

compilers on our Libstock website. Just

download them and you are ready to start.

.com

6. Dimensions

MikroElektronika assumes no responsibility

or liability for any errors or inaccuracies

that may appear in the present document.

Specication and information contained in

the present schematic are subject to change

at any time without notice.

mm mils

LENGTH 42.9 1690

WIDTH 25.4 1000

HEIGHT* 3.9 154

5. Schematic

9. Support

* without headers

10. Disclaimer

RTC5 click, as the name implies, is the fth

click board™with a real time clock module.

Visit the click board™page to see all available

alternatives. Including RTC click which can

also work on a 5V power supply.

25.4 mm / 1000 mils

42.9 mm / 1690 mils

7. RTC5 click™alternatives

www.mikroe.com/click

Otros manuales de Placa madre de mikroElektronika

mikroElektronika

mikroElektronika EasydsPIC6 Manual de usuario

mikroElektronika

mikroElektronika mikroProg Manual de usuario

mikroElektronika

mikroElektronika click MPU 9DOF Manual de usuario

mikroElektronika

mikroElektronika mikromedia for dsPIC33 Manual de usuario

mikroElektronika

mikroElektronika mikromedia 7 Manual de usuario

mikroElektronika

mikroElektronika mikromedia for STM32 Guía de inicio rápido

mikroElektronika

mikroElektronika EasyPIC 6 Manual de usuario

mikroElektronika

mikroElektronika SmartGLCD Manual de usuario

mikroElektronika

mikroElektronika Clicker 2 Manual de usuario

mikroElektronika

mikroElektronika Line Follower click Manual de usuario

mikroElektronika

mikroElektronika Vibra sense click MIKROE-1927 Manual de usuario

mikroElektronika

mikroElektronika EasyAVR v7 Manual de usuario

mikroElektronika

mikroElektronika mikromedia for Stellaris M3 Manual de usuario

mikroElektronika

mikroElektronika Clicker 2 Manual de usuario

mikroElektronika

mikroElektronika Ready for PIC MIKROE-766 Manual de usuario

mikroElektronika

mikroElektronika mikroProg Manual de usuario

mikroElektronika

mikroElektronika 10DOF click Manual de usuario

mikroElektronika

mikroElektronika MINI-32 Manual de usuario

mikroElektronika

mikroElektronika Altitude click Manual de usuario

mikroElektronika

mikroElektronika Joystick click Manual de usuario

mikroElektronika

mikroElektronika 4-20mA click Manual de usuario

mikroElektronika

mikroElektronika mikromedia+ for PIC32MX7 Manual de usuario

mikroElektronika

mikroElektronika USB UART click Manual de usuario

mikroElektronika

mikroElektronika EasyMx PRO v7 Guía de inicio rápido

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario

mikroElektronika click BOARD RTC 5 Manual de usuario

Manuales populares de Placa madre de otras marcas