Mikroe DAC 2 click Manual de usuario
2 3
click
BOARD™
www.mikroe.com
2. Soldering the headers
3. Plugging the board in
Once you have soldered the headers your
board is ready to be placed into the desired
mikroBUS™socket. Make sure to align the cut
in the lower-right part of the board with the
markings on the silkscreen at the mikroBUS™
socket. If all the pins are aligned
correctly, push the board all the
way into the socket.
Turn the board upward again. Make sure
to align the headers so that they are
perpendicular to the board, then solder the
pins carefully.
Turn the board upside down so that
the bottom side is facing you upwards.
Place shorter pins of the header into the
appropriate soldering pads.
Before using your click board™, make sure
to solder 1x8 male headers to both left and
right side of the board. Two 1x8 male headers
are included with the board in the package.
4. Essential features
DAC 2 click contains two analog output screw
terminals: Vout and GND. 16-bit data is sent
to the DAC through SPI. The digital value is
converted to the appropriate voltage level
in the range between GND and REFERENCE
(VCC or 4.096V), which is proportional to the
received 16-bit number.
1
DAC 2 click carries LTC2601CDD, a 16-bit
digital-to-analog converter, along with volt-
age output screw terminals. The chip has high
rail-to-rail output drives (±15mA, Min) and
double-buered data latches. The click board
communicates with the target MCU through
the mikroBUS™SPI interface (MISO, MOSI
pins) with clock rates up to 50MHz. Addition-
ally, the CLR pin, in place of default mikroBUS™
RST pin, clears all the registers. The board
uses either a 3.3V or 5V power supply.
DAC 2 click
1. Introduction
DAC 2 click manual
ver 1.00
0100000085011
Downloaded from Arrow.com.
AN
RST
CS
SCK
MOSI
MISO
+3.3V
GND
PWM
INT
RX
TX
SCL
SDA
+5V
GND
MIKROBUS
DEVICE
CONN.1
GNDGND
POWER SELECTOR
VCC
LTC2601CDD
CLR
4GND 8
VOUT 7
VREF 6
SDI
2
SCK
3
CS/LD
5
SDO
1
VCC 9
LDAC 10
U1
MOSI
SCK
CLR
CS
GND
VCC
CN1
GND
VOUT
R1
4K7
PWR
GND
VCC
MOSI
SCK
CS
CLR
C1
100nF
VCC
GND
VREF
VCC
VREF
VCC-REF
3
1
2
VIN
GND
VOUT
REF1
MCP1541 GND
VCC
4.096V
VCC-REF
VCC
E1
10uF
GND
8. Code examples
MikroElektronika oers free tech support
(www.mikroe.com/support) until the end of
the product’s lifetime, so if something goes
wrong, we’re ready and willing to help!
Once you have done all the necessary
preparations, it’s time to get your click board™
up and running. We have provided examples
for mikroC™, mikroBasic™and mikroPascal™
compilers on our Libstock website. Just
download them and you are ready to start.
.com
6. Dimensions
MikroElektronika assumes no responsibility
or liability for any errors or inaccuracies
that may appear in the present document.
Specication and information contained in
the present schematic are subject to change
at any time without notice.
Copyright © 2015 MikroElektronika.
All rights reserved.
mm mils
LENGTH 28.6 1125
WIDTH 25.4 1000
HEIGHT* 10.15 400
5. Schematic
7. SMD jumpers 10. Disclaimer
9. Support
25.4 mm / 1000 mils
28.6 mm / 1125 mils
* without headers
DAC 2 click features two SMD jumpers: PWR
SEL for switching between a 3.3V or a 5V
power supply, and REF SEL for choosing
either VCC or 4.096V as a reference voltage.
Downloaded from Arrow.com.Downloaded from Arrow.com.
Este manual sirve para los siguientes modelos
1
Otros manuales de Placa portadora de Mikroe
