Miele DA 5960 W Manual de usuario

Installation Instructions

DA5960 W en-CA

Read these instructions and the "Important Safety Instructions" before installing

this hood.

Installation, repair and maintenance work should be performed by a

Miele authorized service technician in accordance with national and

local safety regulations and the provided installation instructions.

Disposal of packing material

The cardboard box and packing

materials protect the appliance during

shipping. They have been designed to

be biodegradable and recyclable.

Please recycle.

,DANGER

Ensure that any plastic wrappings,

bags, etc., are disposed of safely

and kept out of the reach of babies

and young children. Danger of

suffocation!

Disposal of an old appliance

Old appliances may contain materials

that can be recycled. Please contact

your local recycling center about the

possibility of recycling these materials.

Before discarding an old appliance,

disconnect it from the electrical

supply and cut off the power cord to

prevent it from becoming a hazard.

Caring for the environment

Appliance dimensions

1) Air extraction mode

2) Recirculation mode

3) Recirculation vent installed upwards

4) and 5) Installation area

Wall/ceiling area respectively for vent

hole and outlet installation.

For recirculation mode only 4)

and only outlet installation.

Ductwork ø 6" (150 mm), with reducing

colla rø4 15/16" (125 mm)

6) If you plan to haveatiled

backsplash or wall panel underneath

the exhaust hood, this may cause

difficulties when changing the filter,

depending on the thickness and height

of the tiles or panel.

If this is the case the filter needs to be

turned 180° and inserted the other way

round.

Appliance dimensions

9742iad

Les appareils de Miele peuvent être encastrés à ras ou avec débordement. Discutez

de vos conditions d'installation avec votre architecte, décorateur de l'intérieure et

installateur.

Distance between cooktop and

hood (S)

Do not install this exhaust hood over

cooktops burning solid fuel.

Provided a larger distance is not

given by the manufacturer of the

cooktop, follow the minimum safety

distances between a cooktop and

the bottom of the hood:

Miele cooktops:

- 24" (610 mm) above electric

surfaces,

- 26" (660 mm) above electric

grill/boiler/fryers,

- 24" (610 mm) above gas surfaces

ß25,000 BTU's (7.5 kW) and no

burner greater than 10,250 BTU's

(3 kW) ,

- 30" (762 mm) above gas surfaces

> 25,000 BTU's (7.5 kW),

- 30" (762 mm) above burner heads

> 10,250 BTU's (3 kW). For

example, a Wok used separately

or in combination with a cooktop.

Non-Miele cooktops:

- 24" (610 mm) above all electric

surfaces,

- 30" (762 mm) above all gas

surfaces,

- 26" (660 mm) above electric

grill/boiler/fryers.

If several gas surfaces are installed

under the hood, the total output must

be considered when determining the

minimum safety distance.

Be sure to follow the minimum safety

distances given by the gas cooktop

manufacturer to easily flammable

materials e.g. upper cabinets.

If local building codes require a

greater safety distance, follow their

requirement.

If there is more than one appliance

beneath the hood and they have

different minimum safety distances

always select the greater distance.

See "Important Safety Instructions"

for further information.

The installation procedure differs

depending on the model and venting

method.

Before beginning the installation:

^Read all instructions.

^Determine height (S), regarding the

user’s body height, i.e. a comfortable

height for the user.

However, the greater the distance the

less effectively cooking odors are

drawn in.

^If the hood is fitted flush to the

ceiling, regard the possible unit

height when selecting the installation

height.

Appliance dimensions

Use the following distances when

preparing a rear wall (screw ø 5 mm).

*The middle retaining plate can vary in

position, depending on the ventilation

gap and the position of the outlet. It

should be mounted as low as possible.

If the exhaust hood is being mounted

directly on the wall, follow the enclosed

assembly.

Appliance dimensions

Installation accessories

dai2417

a3 protective shields

to prevent scratches to the chimney

during installation.

b2 hose clips

for securing the ducting.

c1 reducing collar

for use with 5" (125 mm) exhaust

ducting.

d2 protective strips

for chimney mounting

eUpper retaining plate secures the

chimney extension

fMiddle retaining plate for additional

stability of the chimney

gLower retaining plate secures the

canopy and motor assembly.

hInstallation kit for recirculation

mode; contains diverter and hose

(optional accessory)

1 lever for dismantling the chimney

Installation instruction diagram

8 large headed screws5x40mm

for securing the retaining plates and the

canopy

(S8 wall anchors included in the

packaging are not for use in USA)

2 M 6 locking nuts

for securing the unit

1 allen wrench

for adjusting the unit height

,CAUTION

To avoid risk of hand or other injury,

avoid contact with sharp edges

during the assembly and installation

process.

Installation accessories

The majority of the weight of the

installed ventilation system will be

supported by the lower retaining

plate. It must be firmly attached to

the stud framing behind the drywall.

If studs are not available in the

required locations, a plywood

backing (min. ½" (13 mm) thick)

spanning at least two studs must be

installed. Failure to adequately

support the weight as stated may

result in the ventilation system falling

off the wall, causing personal injury

and property damage.

(If plywood backing is not needed,

proceed to the included "Installation

diagram".)

To install a plywood backing

^Determine and mark the location of

the retaining plate for the canopy as

outlined on the "Installation diagram".

^Make a cutting line 3" (76 mm) above

and 3" (76 mm) below the outline of

the retaining plate.

^Find the studs to the left and right of

the mounting location by tapping the

wall or using a stud finder.

^Mark a vertical cutting line along the

center of each stud.

,CAUTION

When cutting or drilling into the wall

or ceiling, do not damage electrical

wiring and other hidden utilities.

^Remove the drywall between the

cutting lines and replace it with

plywood of a matching thickness

(min. ½" (13 mm) thick). Tape the

joints and refinish the wall.

^Proceed to the enclosed "Installation

diagram" to complete the installation.

Plywood backing

Installation instructions

^See the enclosed installation

instruction diagram.

^Please read the "Important Safety

Instructions" and Installation

instructions before installing this

hood.

Protective film

The casing is covered with a protective

film to prevent scratching during

transport.

^Peel off the film before installing the

casing parts.

Dismantling

If the hood needs to be disassembled,

follow the instructions on the installation

diagram in the reverse order.

A lever is enclosed for easier removal

of the chimney extension.

^After loosening both of the clamping

screws on the chimney, slide the

lever between the chimney and the

chimney extension and gently apply

pressure to ease the chimney from its

hooks.

Installation

Otros manuales para DA 5960 W

Tabla de contenidos

Otros manuales de Campana de ventilación de Miele

Miele

Miele DA 6690 D Manual de usuario

Miele

Miele DUU 150 Manual de usuario

Miele

Miele DA 419-4 Hoja de especificaciones

Miele

Miele DA 3460 Manual de usuario

Miele

Miele DA 2360 Manual de usuario

Miele

Miele DAR 1125 Manual de usuario

Miele

Miele DA 5320 D Manual de usuario

Miele

Miele DA 210-3 Manual de usuario

Miele

Miele DA 249-4 EXT Manual de usuario

Miele

Miele DA 219-3 Manual de usuario

Miele

Miele DA 6881 Manual de usuario

Miele

Miele DA 424 V EXT Hoja de especificaciones

Miele

Miele DA 186 Manual de usuario

Miele

Miele DA 6290 D U Manual de usuario

Miele

Miele DA 252-4 U Manual de usuario

Miele

Miele DA 403 Manual de usuario

Miele

Miele DA 407 Manual de usuario

Miele

Miele DA 7078 D Manual de usuario

Miele

Miele DA 1867 Manual de usuario

Miele

Miele DA 270-4 Manual de usuario

Miele

Miele DA 3366 Manual de usuario

Miele

Miele DA 419-7 Manual de usuario

Miele

Miele DA398-6 Manual de usuario

Miele

Miele DA 409 Manual de usuario

Manuales populares de Campana de ventilación de otras marcas

emmeti

emmeti RECUPA MED A-140 Guía

Nibe

Nibe F135 Manual de usuario

Kuppersberg

Kuppersberg INTRO 60 Instrucciones de instalación y mantenimiento

Zephyr

Zephyr Spruce AK9834BS Guía de instalación

Hisense

Hisense MH6INBG Manual de usuario

Broan

Broan 46000 Manual de usuario

GE Profile PV977 Instrucciones originales

FALMEC

FALMEC FFRIA24W5FS Manual de usuario

Whirlpool

Whirlpool RH2600XL-1 SERIES Manual de usuario

Küppersbusch

Küppersbusch DX ISLA Manual de usuario

ETNA

ETNA AV360RVS Manual de usuario

JUNO

JUNO JDF603E6 Manual de usuario

Tricity Bendix

Tricity Bendix LE 150 Manual

AEG

AEG X68163BV1 Manual de usuario

AEG

AEG 125 D Manual de usuario

Smeg

Smeg KSEV97X Manual de usuario

Nibe

Nibe S Series Guía del usuario

Caple

Caple CCH100 Manual