Miele KFN 14943 SD ed Manual de usuario

Operating and Installation

Instructions

Fridge-Freezer Combination

KFN 14943 SD ed

To prevent accidents

and machine damage

read these instructions

before

installation or use. M.-Nr. 07 589 450

en-CA

,Avoid the risk of electrical shock

- Plug into a grounded 3-prong

outlet.

- Do not move the ground plug.

- Do not use an adapter.

- Do not use an extension cord.

Failure to follow these instructions

can result in death, fire, or electrical

shock.

Improper connection of the

equipment grounding conductor

may result in electric shock.

If you are in any doubt as to whether

the appliance has been properly

grounded, have the appliance

checked by a qualified electrician or

service technician.

Installation, repairs and other work

by unqualified persons could be

dangerous. The manufacturer will

not be held responsible for damage

or injury arising from unauthorized

work.

Before installing the appliance,

verify that the voltage, load and

circuit rating information found on

the data plate match the household

electrical supply.

If there are any questions regarding the

electrical connection of this appliance

to the power supply, please consult a

licensed electrician or call the Miele

Technical Service.

V1-800-565-6435

The appliance is supplied with a

UL-listed, 3-wire power cord and

NEMA 5-15 P plug ready for connection

to a 120 V, 60 Hz supply.

The fuse rating is 15 amps.

The appliance requires a 3-wire

receptacle.

The receptacle must be installed by a

licened electrician only.

In the case of side-by-side installations,

a separate outlet must be used for each

appliance.

Ideally, the power outlet should be next

to the appliance and easily accessible.

Do not connect the appliance to the

power supply by an extension cord.

Extension cords do not guarantee the

required safety of the appliance

(danger of overheating).

If any changes are needed to the

household wiring or power supply, this

work must be performed by a qualified

electrician.

Electrical information

Do not place any devices that

produce heat (such as a toaster or

microwave) on top of the appliance.

This would increase the energy

consumption of the appliance!

This fridge/freezer should not be

placed side-by-side with a second

model.

Because the appliance does not

have heated side walls, a

side-by-side arrangement can lead

to the build-up of condensation

water.

Contact your dealer for advice.

Location

The appliance should not be installed

directly next to a heat source (such as

a kitchen range or a heater) or in direct

sunlight. The higher the ambient

temperature, the longer the appliance

will run and the higher the energy

consumption.

Choose a dry, well-ventilated room for

installation.

Climate range

The appliance is designed for use

within a certain climate range (room

temperature range) and should not be

used outside this range. The climate

range is stated on the data plate inside

the appliance.

Climate range Room temperature

+10 °C to +32 °C

+16 °C to +32 °C

+16 °C to +38 °C

+16 °C to +43 °C

If the room is too cold, it will cause the

cooling system in the appliance to

switch off for too long. This may lead to

higher temperatures in the appliance

and the frozen food may even start

thawing!

Proper ventilation

The air behind the appliance gets

warm. In order to ensure adequate

ventilation, you must make sure that the

ventilation slits are not covered or

blocked in any way.

Also, the ventilation slits must be

dusted/cleaned on a regular basis.

Installation

^First remove any cable clips from the

rear of the appliance.

^Check that all the parts on the rear of

the appliance are free to move.

Remove any obstructions.

^Gently slide the appliance into the

desired location.

^The rear of the appliance can be

directly against the wall.

Installation information

Adjustments

^Use the wrench provided to adjust

the feet as needed, so that the

appliance is level.

^If necessary, unscrew the foot a

from the hinge bracket in order to

support the appliance door.

Installation information

Appliance dimensions

ABC

KFN 14943 SD ed 2020 750 630

Installation information

The appliance comes with right-hand

hinging. If left-hand door hinging is

preferred, then follow these instructions

to change the door hinge:

You will need the following tools:

–a crosstip screwdriver,

–a flathead screwdriver,

–various sizes of Torx screwdrivers,

–a fork wrench.

Always change the door hinging

with the assistance of another

person.

Removing the door handles:

^When you pull on the door handle a,

the sidebar bmoves backwards.

^Pull the sidebar bbackwards out of

the track.

^Now loosen the 4 screws (Torx 15) in

the mounting plate and remove the

handle.

^Remove the covers from the opposite

side and place them on the holes that

are now vacant.

Changing the door hinging

Before changing the hinging,

remove any items of food from the

shelves in the appliance door.

Removing the top soft-close

mechanism:

^Open the top door of the appliance.

^Loosen the panel afrom the

soft-close mechanism: From below,

slide a flathead screwdriver into the

recesses, then slowly and carefully

lift off the panel.

Be careful not to damage the door

seal.

If the door seal is damaged, the

appliance door may not close

properly and there will not be

enough refrigeration!

^Slide the panel ain the direction of

the appliance and leave it hanging

between the door and the appliance.

^Place the securing device b

(supplied with the appliance) on the

soft-close mechanism cso that it

engages.

With the securing device in place, the

joint cannot snap shut. Do not remove

the securing device until instructed to!

^Using a flathead screwdriver,

carefully lift the top and the bottom of

the cover dfrom the retainer.

^Push the pin eup and out using a

flathead screwdriver.

Changing the door hinging

^Remove the cover d.

Now the soft-close mechanism and the

appliance are no longer connected.

^Remove the panel a.

^Push the shock absorber arm fas

far as possible towards the handle

side.

^Loosen the three screws gon the

soft-close mechanism and the

spacer.

^In the middle, pry out the housing

with the soft-close mechanism using

a flathead screwdriver.

^Then, pry the housing with the

soft-close mechanism out of the

retainer from the appliance side.

^Lay the soft-close mechanism aside.

^Push out the spacer towards the

hinge side.

^Lay the spacer aside.

Removing the top door of the

appliance:

^Loosen the cover hby carefully

sliding a flathead screwdriver from

below into the recess.

^Remove the cover htogether with

the mounting bracket i.

^Loosen the mounting bracket ifrom

the cover hby pushing it slightly to

the left and then removing the cover

plate towards the front.

^Turn the mounting bracket i180°.

^Place the cover honto the front of

the mounting bracket iand push it

to the right. The writing must be

visible.

^Unscrew the bearing jmechanism,

turn it 180° and replace it on the

opposite side. If necessary,

pre-punch the screw holes.

^Remove the top cover kby pushing

it from back to front and lifting it up.

^Remove the cover lupwards.

Changing the door hinging

Caution! The top door of the

appliance is no longer secured as

soon as the hinge bracket is

removed when following the

instructions below!

^Close the top door of the appliance.

^Loosen the screws mon the top

hinge bracket nand remove the

hinge bracket by pulling up.

^Carefully lift and remove the top door

of the appliance and set aside.

^Make sure that the bearing pin in the

middle of the appliance stays in

place, otherwise the bottom door of

the appliance has no hold!

^Engage the cover htogether with

the mounting bracket ion the

opposite side.

^Now place the cover lon the other

side.

Removing the bottom soft-close

mechanism:

^Open the bottom door of the

appliance.

^Loosen the panel aof the soft-close

mechanism: Slowly pry the panel off

from the top.

Be careful not to damage the door

seal.

If the door seal is damaged, the

appliance door may not close

properly and there will not be

enough refrigeration!

^Slide the panel ain the direction of

the appliance and leave it hanging

between the door and the appliance.

^Place the securing device b

(supplied with the appliance) on the

soft-close mechanism c.

With the securing device in place, the

joint cannot snap shut. Do not remove

the securing device until instructed to!

^From the side, carefully lift off the

cover dusing a flathead

screwdriver.

^If necessary, lift the appliance

backwards slightly with the

assistance of another person.

Changing the door hinging

^Push the pin eup and out.

Now the soft-close mechanism and the

appliance are no longer connected.

^Remove the panel a.

^Push the shock absorber arm fas

far as possible towards the handle

side.

^Loosen the three screws gon the

soft-close mechanism and the

spacer.

^In the middle, pry out the housing

with the soft-close mechanism using

a flathead screwdriver.

^Then, pry the housing with the

soft-close mechanism out of the

retainer from the appliance side.

^Lay the soft-close mechanism aside.

^Push out the spacer towards the

hinge side.

^Lay the spacer aside.

Removing the bottom door of the

appliance:

^Close the bottom door of the

appliance.

^Pull the bearing pin iin the middle

of the appliance up and out.

^Carefully lift and remove the bottom

door of the appliance and set aside.

^Pull the cover doff.

^Unscrew the hinge bracket e, rotate

it 180°, then screw it onto the

opposite side.

^Turn the plastic cap h180° and

replace it on the hinge bracket kin

the middle.

^Now place the cover lon the other

side.

Changing the door hinging

Otros manuales para KFN 14943 SD ed

Tabla de contenidos

Otros manuales de Refrigerador de Miele

Miele

Miele K 32223 i Manual de usuario

Miele

Miele K 2602 Vi Instrucciones de instalación

Miele

Miele K 9457 iD-4 Hoja de especificaciones

Miele

Miele K 9454 iF Hoja de especificaciones

Miele

Miele KF 7564 S ed-1 Hoja de especificaciones

Miele

Miele KFN 9859 iDE Manual de usuario

Miele

Miele KFNS 37432 iD Manual de usuario

Miele

Miele KFN 15842 D edt/cs Manual de usuario

Miele

Miele K 35422 iD Manual de usuario

Miele

Miele KF 1801 SF Hoja de especificaciones

Miele

Miele K 32222 i Manual de usuario

Miele

Miele KFNF 9955 iDE Manual de usuario

Miele

Miele K 14827 SD Manual de usuario

Miele

Miele KFN 9755 IDE Manual de usuario

Miele

Miele KDN 12823 S Hoja de especificaciones

Miele

Miele K 2329 S Manual de usuario

Miele

Miele KDN 12623 S -1 Manual de usuario

Miele

Miele K 37472 iD Manual de usuario

Miele

Miele KF 7654 SNE ed Hoja de especificaciones

Miele

Miele K 8967 S ed-1 Instrucciones de montaje

Miele

Miele K 31222 Ui Manual de usuario

Miele

Miele KFN 29233 D bb Manual de usuario

Miele

Miele K 852i Hoja de especificaciones

Miele

Miele K 8767 S ed Hoja de especificaciones

Manuales populares de Refrigerador de otras marcas

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manual de usuario

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manual de usuario

Sharp

Sharp SJ-BA31IEXW2-EU Manual de usuario

CORBERO

CORBERO CC2300MCW Manual de usuario

KitchenAid

KitchenAid 2205264 Manual de usuario

Stengel

Stengel KU 1101 A++ Manual de usuario

NEFF

NEFF KI181 Series Manual de usuario

Hoshizaki

Hoshizaki Reach-In Manual de usuario

Amana

Amana ASD2524VES00 Manual de usuario

BOMANN

BOMANN KGC 213 Manual de usuario

Danby

Danby DAR044A1SLDD Instrucciones de montaje

Samsung

Samsung RF323TE Manual de usuario

Beko

Beko CSA31022 Manual de usuario

IKEA

IKEA FROSTIG C 185 E Manual de usuario

Electrolux

Electrolux ER 6821 D Manual de usuario

True

True TS-28 Manual de usuario

Frigidaire

Frigidaire FSC23R5DW9 Manual de usuario

Beko

Beko LSP4579W Manual de usuario