Miele KM 5840 Manual de usuario
Installation Instructions
KM 5840 HQ&$
KM 5860
KM 5880
,QVWDOODWLRQUHSDLUDQGPDLQWHQDQFHZRUNVKRXOGEHSHUIRUPHGE\
D0LHOHDXWKRUL]HGVHUYLFHWHFKQLFLDQLQDFFRUGDQFHZLWKQDWLRQDO
DQGORFDOVDIHW\UHJXODWLRQVDQGWKHSURYLGHGLQVWDOODWLRQLQVWUXFWLRQV
Note to the installer:
Please leave this instruction book
with the consumer for the local
electrical inspector’s use.
The minimum distances given in
these Installation Instructions must
be observed in order to ensure safe
operation. Failure to do so increases
the risk of fire.
The cabinetry and venting hood
should be installed first to prevent
damage to the cooktop.
~The countertop must be bonded
with heat resistant (212°F/100°C)
adhesive to prevent distortion or
dissolving.
Any back splashes should also be
heat-resistant.
~The cooktop must not be installed
over a dishwasher, washer, dryer,
refrigerator or freezer. Heat radiated by
the cooktop may damage them.
~To eliminate the risk of burns or fire
by reaching over heated surfaces
cabinet storage space above the
appliance should be avoided. If cabinet
storage is necessary, the risk can be
reduced by installing a venting hood to
project horizontally a minimum of 5"
(127 mm) beyond the bottom of the
cabinets.
~This appliance has not been
designed for maritime (e.g. ships) use
or for use in mobile installations such as
recreational vehicles or aircraft.
However, under certain conditions it
may be possible for installation in these
applications. Please contact the Miele
Technical Service Department with
specific requirements.
~You must ensure the power cable
for the appliance will not come into
contact with the floor panel after
installation, nor be subject to any
mechanical strain.
~The cooktop must not be
permanently sealed into the countertop
when installed. The sealing strip under
the edge of the cooktop provides a
sufficient seal for the countertop. See
"Sealing".
~The safety distances specified in
these instructions must be followed
carefully.
Keep this instruction book in a safe
place for reference and pass it on to
any future user.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
40
Safety distance from divider
Installation of a divider under the
cooktop is not required.
If a divider is fitted under the cooktop,
the distance between the upper edge
of the work surface and the upper edge
of the divider must be at least4½"
(110 mm).
A gap of at least 1 3/8"" (35 mm) must
be provided between the rear edge of
the divider and the rear wall of the
cabinet so that the power cord can be
passed through.
Safety distances above the
appliance
The minimum safety distance given by
the hood manufacturer must be
maintained between the cooktop and
the hood above it. See the installation
instructions of the hood for these safety
measurements.
If the hood manufacturer's instructions
are not available or if flammable objects
are installed over the cooktop
(e.g. cabinets, utensil rail, etc.), a
minimum safety distance of 30"
(760 mm) must be maintained.
If there is more than one appliance
beneath a hood (e.g. wok burner
and electric cooktop), and they have
different minimum safety distances,
always observe the greater
distance.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
41
Safety distances to the sides
of the appliance
The appliance should only be installed
as shown in the illustrations, while
maintaining the required safety
distances shown. Do not install the
appliance between two tall cabinets,
this is a fire hazard.
a1 5/8" (40 mm) minimum distance
from the countertop cut-out to the
rear edge of countertop or wall.
bMinimum distance from the right of
the countertop cut-out to the closest
adjacent piece of furniture (for
instance, a high cabinet) or a room
wall.
KM 5840 = 2" (50 mm)
KM 5860 / KM 5880 = 4" (100 mm)
c2" (50 mm) minimum distance from
the left of the countertop cut-out to
the closest adjacent piece of
furniture (for instance, a high
cabinet) or a room wall.
not allowed
recommended
not recommended
not recommended
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS
42
Safety distance from the wall covering
If a wall covering is installed, a minimum safety distance must be maintained
between the countertop cut-out and the covering, since high temperatures can
damage these materials.
If the covering is made of a combustible material (such as wood), the distance
between the countertop cut-out and the wall covering must be a minimum of
2" (50 mm).
For coverings made of non-combustible materials (such as metal, marble, granite
or ceramic tiles) the minimum safety distance ebetween the countertop cut-out
and the wall covering must be 2" (50 mm) minus the thickness of the covering.
For example: thickness of wall covering 9/16" (15 mm)
2" (50 mm) - 9/16" (15 mm) = minimum safety distance 1 3/8" (35 mm).
Cooktops flush with the countertop Frame/Facet cooktops
aWall frame
bWall covering
x= thickness of the wall covering
cCountertop
dCountertop cut-out
eMinimum safety distance
with flammable materials 2" (50 mm)
with non-flammable materials 2" (50 mm) minus x
Installation
43
Frame/Facet Cooktops
Sealing
The appliance must not be permanently
sealed into the countertop when
installed. The sealing strip under the
edge of the appliance provides a
sufficient seal for the countertop.
If the appliance is sealed into
position, the countertop or appliance
could be damaged if it needs to be
removed for maintenance or service.
Tiled surfaces
The grouting aand shaded area under
the appliance frame must be flat and
even so that the frame will lie evenly
and the sealing strip under the edge of
the upper part of the appliance can
provide an adequate seal against the
countertop.
Installation
44
KM 5840
aSpring clips
bFront
cInstallation height
dConnecting cable, Length = 56 11/16" (1440 mm)
eRating label
Installation dimensions
45
KM 5860
aSpring clips
bFront
cInstallation height
dConnecting cable, Length = 56 11/16" (1440 mm)
eRating label
Installation dimensions
46
KM 5880
aSpring clips
bFront
cInstallation height
dConnecting cable, Length = 56 11/16" (1440 mm)
eRating label
Installation dimensions
47
The exact positions of the spring
clamps and the support bars (for
beveled cooktops only) are shown in
the "Installation dimensions" of each
unit.
Facet cooktops:
A special sealing strip ensures the
slip-proof seating of the cooktop in
the cutout. The gap between the
frame and the countertop will narrow
after a little time has passed.
^Create the countertop cutout as
shown in the "Installation
dimensions". Observe the safety
distances (see "Installation Safety
Instructions").
Wood or solid surface countertop
^Seal the cut surfaces with a suitable
sealant to avoid swelling caused by
moisture.
The materials used must be heat
resistant.
Ensure that these materials do not
get on the top surface of the
countertop panels.
^Position the spring clips and the
securing strips (supplied with the
appliance; only for facet cooktops)
on the top edge of the cut-out
^Attach the spring clips aand the
securing strips bwith the
3.5 x 25 mm wood screws (supplied).
Installation
48
Otros manuales para KM 5840
3
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Placa de cocina de Miele
Miele
Miele KM 406 Manual de usuario
Miele
Miele CS 1221 Manual de usuario
Miele
Miele ProLine Teppanyaki CS 1327 Manual de usuario
Miele
Miele KM 2030 Manual de usuario
Miele
Miele GAS COMBISET CS 1012 Manual de usuario
Miele
Miele CS 1018 G Manual de usuario
Miele
Miele KMR 1124 G Manual de usuario
Miele
Miele KM 404 Manual de usuario
Miele
Miele SmartLine Tepan Yaki CS 7632 Manual de usuario
Miele
Miele KM 5656 Manual de usuario
Miele
Miele KM 320 Manual de usuario
Miele
Miele SmartLine CS 7612 FL Manual de usuario
Miele
Miele KM 5731 Manual de usuario
Miele
Miele CS 1112 Manual de usuario
Miele
Miele GAS COMBISET CS 1011 Manual de usuario
Miele
Miele KM 2354 Manual de usuario
Miele
Miele KM 5603 Manual de usuario
Miele
Miele KM6357 Manual de usuario
Miele
Miele KM-5600 Manual de usuario
Miele
Miele KM 2355 G Manual de usuario
