Microsemi FlashPro Lite Manual técnico

© 2013 Microsemi Corporation. All rights reserved.

FlashPro Lite Device Programmer

Quickstart Card

This quickstart card applies only to the FlashPro Lite device programmer.

Kit Contents

Software Installation

If you are already using Libero®System-on-Chip (SoC) software, you have the FlashPro software

installed as part of this software. If you are using the FlashPro Lite device programmer for

standalone programming or on a dedicated machine, download and install the latest release of the

FlashPro software from the Microsemi SoC Products Group website. The installation will guide you

through the setup. Complete the software installation before connecting the FlashPro Lite device

programmer to your PC. The installation will ask you “Will you be using FlashPro Lite or FlashPro

programmer via parallel port?”, answer “Yes”.

Software releases: www.microsemi.com/soc/download/program_debug/flashpro.

Hardware Installation

1. Connect the programmer to a parallel printer port on your PC. Connect one end of the IEEE 1284

cable to the programmer’s connector. Plug the other end of the cable into your parallel printer

port and tighten the screws. You should not have any licensing dongles connected between the

parallel port and cable. Your port settings must be EPP or bidirectional. Microsemi also supports

ECP mode with FlashPro v2.1 software and newer.

2. Verify that you are connected to the correct parallel port on your computer. Microsemi

recommends that you dedicate a port to the programmer. Connecting to a serial port or a third-

party card can damage the programmer. This type of damage is not covered by the warranty.

3. Connect the FlashPro Lite ribbon cable to the programming header and turn the target board on.

Quantity Description

1 FlashPro Lite programmer standalone unit

1 Ribbon cable for FlashPro Lite

1 IEEE 1284 parallel port cable

50200200-1/2.13

FlashPro Lite Device Programmer Quickstart Card

Common Issues

If you see two blinking LEDs on the programmer after you have connected the programmer to the

parallel port, make sure the parallel port cable is connected firmly to the PC parallel port. For more

information, refer to the FlashPro Software and Hardware Installation Guide and the “Known

Issues and Workarounds” section of the FlashPro software release notes:

www.microsemi.com/soc/download/program_debug/flashpro.

Documentation Resources

For further FlashPro software and FlashPro Lite device programmer information, including user's

guide, installation guide, tutorial, and application notes, refer to the FlashPro software page:

www.microsemi.com/soc/products/hardware/program_debug/flashpro.

Technical Support and Contacts

Technical support is available online at www.microsemi.com/soc/support and by email at

soc_tech@microsemi.com.

Microsemi SoC Sales offices, including Representatives and Distributors, are located worldwide. To

find your local representative visit www.microsemi.com/soc/company/contact.

Tabla de contenidos

Otros manuales de Placa madre de Microsemi

Microsemi

Microsemi LX1918 Manual de usuario

Microsemi

Microsemi VSC8574 Manual de usuario

Microsemi

Microsemi LX8204 12 V E-Fuse Manual de usuario

Microsemi

Microsemi PD70210EVB Manual de usuario

Microsemi

Microsemi VSC8211 Manual de usuario

Microsemi

Microsemi DS3106DK Manual de usuario

Microsemi

Microsemi Actel IGLOO Icicle Manual de usuario

Microsemi

Microsemi LX7186A Manual de usuario

Microsemi

Microsemi VSC8489 Manual de usuario

Microsemi

Microsemi VSC8257 Manual de usuario

Microsemi

Microsemi PD-IM-7401 Manual de usuario

Microsemi

Microsemi FlashPro4 Manual de usuario

Microsemi

Microsemi LX7720 Manual de usuario

Microsemi

Microsemi LX7165 Manual de usuario

Microsemi

Microsemi PD69208 Manual de usuario

Microsemi

Microsemi SmartFusion2 MSS Manual de usuario

Microsemi

Microsemi VSC8221 Manual de usuario

Microsemi

Microsemi SmartFusion UG0209 Manual de usuario

Microsemi

Microsemi IGLOO PLUS Starter Kit Manual de usuario

Microsemi

Microsemi ProASIC3/E Proto Kit Manual técnico

Microsemi

Microsemi LX7180A Manual de usuario

Microsemi

Microsemi LX7175 Manual de usuario

Microsemi

Microsemi VSC8584 Manual de usuario

Microsemi

Microsemi FlashPro5 Manual técnico

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario