Microscan LVS-9580 Manual de usuario
M-9580-4.0.0-E-En-0 P/N 84-9310011-02 Rev A
LVS® 9580 Operating Instructions
English
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 2 of 17
Copyright ©2016
Microscan Systems, Inc.
Tel: +1.425.226.5700 / 800.762.1149
Fax: +1.425.226.8250
All rights reserved. The information contained herein is proprietary and is provided solely for the purpose of
allowing customers to operate and/or service Microscan manufactured equipment and is not to be released,
reproduced, or used for any other purpose without written permission of Microscan.
Throughout this manual, trademarked names might be used. We state herein that we are using the names to the
benefit of the trademark owner, with no intention of infringement.
GS1 Solution Partner
Disclaimer
The information and specifications described in this manual are subject to change without notice.
Latest Manual Version
For the latest version of this manual, see the Download Center on our web site at:
www.microscan.com.
Technical Support
For technical support, e-mail: helpdesk@microscan.com.
Warranty
For current warranty information, see: www.microscan.com/warranty.
Microscan Systems, Inc.
United States Corporate Headquarters
+1.425.226.5700 / 800.762.1149
United States Northeast Technology Center
+1.603.598.8400 / 800.468.9503
European Headquarters
+31.172.423360
Asia Pacific Headquarters
+65.6846.1214
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 3 of 17
Table of Contents
IMPORTANT INFORMATION.........................................................................................4
SAFETY INSTRUCTIONS ..............................................................................................4
ABOUT THE LVS-9580 ..................................................................................................5
Quiet Zone..................................................................................................................5
HARDWARE OVERVIEW...............................................................................................6
LVS-95XX SOFTWARE STEPS .....................................................................................7
Log On to the LVS-95XX Software..............................................................................7
Turn on the LVS-9580 Camera....................................................................................9
Calibrate the LVS-9580.............................................................................................10
GRADING BARCODES................................................................................................13
CLEANING INSTRUCTIONS........................................................................................14
ENGINEERING SPECIFICATIONS ..............................................................................15
Supported Symbologies and Standards ....................................................................16
Supported Symbologies.........................................................................................16
Supported Standards.............................................................................................17
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 4 of 17
Important Information
The LVS-9580 arrives to your site packaged in a specially designed shipping carton. DO NOT
discard this shipping carton in case you must ship or store the system for any reason. Failure
to use this carton when returning your product to Microscan will void warranty.
This guide is intended to help you understand the features and functionality of the LVS-9580.
Be sure to reference the following additional resources:
oRefer to the “LVS-95XX Series Software Installation Guide” for steps on installing the
LVS-95XX software. A hard copy version of the “LVS-95XX Series Software Installation
Guide” is packaged with your system and an electronic version is located on the
installation media.
oRefer to the “LVS-95XX Series Barcode Quality Station Operations Manual” for
comprehensive steps on operating the LVS-95XX software. This manual is located on the
installation media packaged with your system.
If you have any questions or concerns about the performance of the LVS-9580, please call
your local Microscan Distributor or Microscan technical support:
Microscan Technical Support:
+1-425-203-4841 | +1-800-762-1149 | [email protected]
Safety Instructions
The LVS-9580 has been carefully designed to provide years of safe, reliable performance.
However, as with all electrical equipment, there are some basic precautions you should follow to
avoid personal injury or damage to the system:
Before using the system, carefully read all the installation and operating instructions.
Observe all warning instruction labels on the system.
Never insert anything into the openings of the system.
Do not use the system near water or spill liquid into it.
All components used to create your system are CE approved. All circuits were designed to
incorporate maximum safety. However, any equipment using electrical voltages may cause
personal injury if improperly handled.
Do not attempt to work on the system with the USB cable connected.
To avoid damaging the system, unplug the USB cable before cleaning.
If the system ever needs repair, consult Microscan or your Microscan Distributor.
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 5 of 17
About the LVS-9580
The LVS-9580 is a portable, handheld barcode verifier designed for off-line verification of
barcodes to ISO/IEC standards. The LVS-9580 is a 5.0 megapixel camera-based system that
grades linear (1D) and two-dimensional (2D) codes up to 3 inches (76 mm) wide and up to 2
inches (51 mm) tall (including the quiet zone). See the “Quiet Zone” section below for more
information on quiet zones.
The LVS-9580 verifies barcode labels located on a variety of surfaces including corrugated
cardboard boxes, shipping containers, and on a static (non-moving) web. The LVS-9580 grades
barcodes in either picket fence or ladder orientation.
Picket Fence Orientation
Ladder Orientation
The LVS-9580 is 21 CFR Part 11 Compliant-Ready.
Quiet Zone
The Quite Zone is a clear space preceding the start character of a barcode symbol and follows
the stop character. When reading/grading a barcode symbol, you must allow enough space for
the Quiet Zone. The required Quiet Zone space for each barcode varies by symbology. An error
message appears on the computer screen if not enough space has been allowed for the Quiet
Zone.
1D Barcode Quiet Zone
2D Barcode Quiet Zone
Quiet
Zone
Quiet
Zone
Quiet
Zone
Start
Character
Stop
Character
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 6 of 17
Hardware Overview
The LVS-9580 is comprised of the following hardware components:
USB cable input
connector
Trigger
Enclosure containing
camera and LEDs
Verifier window
Four rubber feet surrounding
verifier window to hold
substrate in place and
prevent slippage
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 7 of 17
LVS-95XX Software Steps
Refer to the sections below for steps on:
Logging on to the LVS-95XX software
Turning on the LVS-9580 camera
Calibrating the LVS-9580
Note: Refer to the “LVS-95XX Series Software Installation Guide” for step-by-
step instructions on installing the LVS-95XX software; a hard copy version of this
guide is packaged with your system and an electronic version is located on the
installation media.
Log On to the LVS-95XX Software
1. Start the LVS-95XX software. The “Welcome” screen appears (see below).
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 8 of 17
2. Click the “Setup” tab. The “Login” box appears.
3. Enter admin (not case sensitive) in the Operator ID field and in the Password field.
4. Click “OK.” You are logged in to the LVS-95XX software.
5. Turn on the LVS-9580 camera by following the steps in the next section entitled “Turn on the
LVS-9580 Camera.”
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 9 of 17
Turn on the LVS-9580 Camera
1. Click the “Setup” tab and select “9580” in the “Camera” section (see below).
Note: If you are using only an LVS-9580 (with no other LVS-95XX barcode
verifier, such as an LVS-9510), then “9580” will be the only camera listed in the
“Camera” section. If you are using an LVS-9580 with an LVS-9510 (1.3 mp or 5.5
mp cameras) or LVS-9505 (1.3 mp or 2.1 mp cameras), then all system cameras
appear in the “Camera” section. Select “9580.”
2. Select “Auto-sector” in the “Grading mode” section (see screenshot above). This allows the
LVS-95XX software to locate a barcode within the field of view and automatically draw a
sector around the barcode.
3. Next, you need to calibrate the LVS-9580 (if using the LVS-9580 for the first time). See the
next section for calibration steps.
Additional camera
9580 camera
Select the “Auto-
sector” option
LVS-9580 Operating Instructions - English
LVS-9580 Operating Instructions - English Page 10 of 17
Calibrate the LVS-9580
IMPORTANT:
The LVS-9580 should be calibrated regularly. The entire calibration process
takes less than 30 seconds to complete and ensures the LVS-9580 is certified
according to industry standards.
The Calibrated Conformance Standard Test Card should be replaced every two
years.
It is recommended to clean the LVS-9580 window prior to calibration. See the
“Cleaning Instructions” section for more information.
1. To calibrate the LVS-9580, click the “Calibration” tab.
2. Locate the Calibrated Conformance Standard Test Card (“test card”) that was packaged with
your system and place the test card on a flat surface.
Below is an example of an “EAN/UPC” test card.
Master Grade
barcodes
Tabla de contenidos
Otros manuales de Lector de código de barras de Microscan
Microscan
Microscan MS-820 Manual de usuario
Microscan
Microscan Quadrus MINI Imager Manual de usuario
Microscan
Microscan MS-820 Manual de usuario
Microscan
Microscan Quadrus MINI Imager Manual de usuario
Microscan
Microscan MicroHAWK ID-30 Manual de usuario
Microscan
Microscan MINI Hawk Manual de usuario
Microscan
Microscan HawkEye 45T Manual de usuario
Microscan
Microscan HE40T Manual de usuario
Microscan
Microscan QX-830 Manual de usuario
Microscan
Microscan Mobile Hawk Manual de usuario
Microscan
Microscan HS-2D Manual de usuario
Microscan
Microscan MS-1 Manual de uso y cuidado
Microscan
Microscan HawkEye 1500 Series Manual de usuario
Microscan
Microscan LVS-9570 Guía del producto
Microscan
Microscan HawkEye 40T Manual de usuario
Microscan
Microscan MINI Hawk Xi Manual de usuario
Microscan
Microscan MS-820 Manual de usuario
Microscan
Microscan LVS-9510 Manual de usuario
Microscan
Microscan MS-9 Manual de usuario
Microscan
Microscan MS-3 Manual de usuario
