Micros MBB-10 Manual de usuario
MD0011-014
Revision A
Page 1 of 15
The MICROS Bump Bar
MBB-10 and MBB-20 User’s Guide
This document describes the MBB features, shows how to adjust the speaker
and LED from the keypad, as well as determine the firmware version and how
to update if required. Other sections describe how to open the unit and
configure the MBB circuit board configuration switches, and to service the
unit.
Introducing the MICROS Bump Bar...........................................................2
Adjusting the LED and Speaker from the Keypad......................................4
MBB Spare Parts .........................................................................................5
Opening the Micros Bump Bar....................................................................8
Specification Summary..............................................................................13
MBB-10 Bracket Dimensional Drawing ...................................................14
MBB-20 Bracket Dimensional Drawing ...................................................15
MD0011-014
Revision A
Page 2 of 15
Introducing the MICROS Bump Bar
The MBB-10 and MBB-20 are shown in the Figure below.
Figure 1: The MBB-10 and MBB-20
•USB Interface - 6ft cable standard.
•Extruded aluminum case /w gasket sealed end caps for spill resistance to
IP55 standards.
•Magnetic keys offer improved tactile response over a membrane switch
and millions of actuations.
•Blue LED with adjustable brightness.
•Internal speaker with adjustable volume.
•The alpha and numeric keys can be reversed to allow the MBB interface
cable to exit from the left or right.
•Order notification through the speaker and LED. Refer to the PMA for
specific POS software support.
MD0011-014
Revision A
Page 3 of 15
Template
Each MBB is supplied with a standard template shown in the illustration.
Mounting Brackets
Each MBB is supplied with a quick release mounting bracket that can be
mounted to a counter, wall surface or current third party KDS mounting
hardware. The MBB-20 bracket hole locations are compatible with the QSR
bumpbar for easy replacement. Refer to the MICROS Bump Bar PMA for
more information about KDS mounting options.
Adjustable LED and Speaker
The MBB includes an internal speaker that serves two functions. The speaker
sounds each time a key is pressed. If supported by the KDS software, the unit
can also beep when an new order is received from the KDS controller. The
keypress and order notification beep volume can be adjusted independently
directly from the MBB keypad.
Figure 2: MBB Speaker and LED
USB Interface Cable
The MBB-10 and MBB-20 both use a 6 ft. (1.8M) USB Interface Cable. If a
longer interface cable is required, you can purchase and install an 11 foot
(3.5M) cable, P/N 700503-070. Another option is the Belkin F3U130-16, a 16
ft. USB 1.1 cable extender. The MBB has been tested with two of the extender
cables connected to the standard KDS controller. The extender cable (P/N
700503-071) does not require an external power supply.
MD0011-014
Revision A
Page 4 of 15
Adjusting the LED and Speaker from the Keypad
The LED brightness and Speaker volume can be adjusted directly from the
keypad at any time. Figure 3, below summaries each adjustment.
Figure 3: Adjusting the LED and Speaker volume from the Keypad
Adjusting the LED Brightness
To adjust the LED brightness, press and hold the [1] and [A] keys, then tap the
[2] key to cycle through the Off, Normal, and Bright settings.
Adjusting the Keypad Speaker
To adjust the volume, press and hold the [1] and [A] keys, then tap the [B] key
to cycle through the Off, Normal, and Loud speaker settings.
Adjusting the Order Notification Beep
To adjust the order notification volume, press and hold the [1] and [A] keys
then tap the [3] key to cycle through the Off, Normal, or Loud settings.
Internal Configuration Switches
The MBB circuit board includes two switches that can be set to send lower
or upper case characters, or reverse the location of the character and
numeric keys for increased mounting flexibility. See Figure 10 for more
information. To open the MBB and access the configuration switches, see
page 8.
MD0011-014
Revision A
Page 5 of 15
MBB Spare Parts
In addition to a 3.5M USB Interface Cable, several other spare parts are
available for the MBB-10 and MBB-20.
USB Interface Cables
Figure 4, below displays the MICROS Part Numbers for the standard 6 foot
(1.8M) and optional 11 foot USB cables. Each cable includes a custom molded
water resistant strain relief.
See page 8 to open the unit.
Figure 4: MBB Upgrade and Replacement USB Interface Cables
MD0011-014
Revision A
Page 6 of 15
Circuit Board, MICROS BUMPBAR - 700364-101
Replacement main board, with firmware. A jumper determines if the board
supports the MBB-10 or MBB-20.
Figure 5: Micros Bump Bar Circuit Board
Bracket, MICROS 20-Key BUMPBAR - 600526-026
Mounting bracket for 20 Key MBB. The hole centers are compatible with
current 3rd party KDS mounting hardware. Mounting hardware not included.
Figure 6: MBB-20 Mounting Bracket
MD0011-014
Revision A
Page 7 of 15
Bracket, MICROS 10-Key BUMPBAR - 600526-025
Mounting bracket for 10 Key MICROS Bumpbar. Mounting hardware not
included.
Figure 7: MBB-10 Mounting Bracket
COVER KIT, FLANGE, RIGHT & LEFT, /W SCREWS and
GASKETS - 000160-012.
Replacement left and right end caps, with gaskets and hardware.
Figure 8: MBB Flanges, Left-Right
MD0011-014
Revision A
Page 8 of 15
Opening the Micros Bump Bar
The following procedure applies to both the MBB-10 and MBB-20.
1. Be sure to disconnect the USB interface cable from the host KDS
controller before you open the unit.
2. Refer to Figure 9 and remove the pair of screws from the side where the
cable exits.
3. Pull the flange and USB cable out far enough to expose the circuit board,
then continue to pull out the board until the connectors are exposed. Avoid
pulling on the keypad ribbon cable when removing the board.
Figure 9: Opening the Micros Bump Bar
•Refer to page 9 to set the internal configuration switches.
•Refer to page 10 to change the USB Interface Cable.
•Refer to page 11 to change the MBB circuit board.
MD0011-014
Revision A
Page 9 of 15
Setting the Internal Configuration Switches
Figure 10 describes the function of the two switches and single 5-pin header on
the MBB Control Board.
Figure 10: MBB Control Board Configuration Switches
SW1 - Selects Normal or Reversed Characters
In the Normal position, numeric characters appear in the top row, ascending
from left to right. Alpha characters appear in the bottom row ascending from
left to right.
SW1 can be set to the ‘Reversed’ position for flexibility when mounting the
MBB. The reversed selection places alpha and numeric characters in
descending order from left to right.
SW2 - Selects Upper or Lower Case Characters
SW2 selects upper or lower case alpha characters. Lower Case is the default.
J2 - Selects MBB-10 or MBB-20 Configuration
J2 determines if the board supports the MBB-10 (2x5) or MBB-20 (2x10)
format.
MD0011-014
Revision A
Page 10 of 15
Remove/Replace the USB Cable
1. Open the MBB case to access the cable as described on page 8.
2. Remove the existing cable from mini-USB Connector J1 and the flange
strain relief as shown in the Figure below.
Figure 11: Replacing the USB Cable
3. Connect the USB Interface cable to J1 and the strain relief in the flange
cut-out.
4. See page 12 to reinstall the circuit board and close the MBB.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Equipo de DJ de otras marcas
thomann
thomann Stairville DJ Lase 40-G MK-III Manual de usuario
Eagletone
Eagletone 6 Eyes Flower Manual de usuario
EuroLite
EuroLite FLD-1508 Manual de usuario
Technical Pro
Technical Pro LG8xSEA Manual de usuario
JB Systems
JB Systems Lounge Laser DMX Manual de usuario
Lightmaxx
Lightmaxx Vega Halo 90 Manual de usuario
Elation
Elation FUZE WASH Z350 Manual de usuario
Maverick
Maverick MK3 WASH Manual de usuario
Infinity
Infinity TF-260C7 Fresnel Manual de usuario
Chauvet
Chauvet EVE E-50Z Manual de usuario
Eliminator Lighting
Eliminator Lighting E 138 Manual de usuario
EuroLite
EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario