Micromax Q392 Manual de usuario

Q392 L3 Service Manual

1. Technical Specifications :

Particular

Remarks

Key Matrix For Flashing

N/A

Chipset

MTK6580 Quad-core

Android Version

Android L

Processor Frequency

1.3GHz

Network Mode

3G WIFI

ROM

8GB

RAM

2GB

Internal memory

5GB

Expandable Memory

32GB

Factory mode code

*#87#

Good Earpiece volume

32 ohm

Good Loudspeaker volume

4 ohm

Good Mic volume

2200 ohm

Good Vibrator volume

32 ohm

2. CAUTIONS

I. Flashing & Servicing must be undertaken by qualified personnel only.

II. Ensure all work is carried out at an anti-static workstation and that an anti-static wrist strap is

worn.

III. Use only approved Tools & components as specified in the parts list.

IV. Ensure all components, modules, screws, and insulators are correctly re-fitted after servicing

and alignment.

Q392 L3 Service Manual

V. Ensure all cables and wires are repositioned correctly if Handset disassembled

VI. Electrostatic discharge can easily damage the sensitive components of electronic products.

Therefore, Service Centre must adhere the precautions which mentioned above.

3. Q392 Level trouble shooting

1) Doesn’t Power On

Solution:

There is no current when the Power Key is pressed; check J1307 to see if there is false soldering, pseudo

soldering or damage, if yes, Carry out Resoldering or replacement;

There is no display when the Power Key is pressed, and the current stays within 100~120mA, if yes, The

problem is caused by pseudo soldering or damage of the MCP (U101);carry out repair soldering or replacement of the

MCP;

When the Power Key is pressed, the display freezes in a certain interface, if yes, Upgrade the software

version;

It should be caused by pseudo soldering or damage of PMIC(U401);

There is heavy current when the Power Key is pressed, if yes, Find the hot point, and replace the

corresponding material (PMIC (U401) and CPU (U101) are damaged in most cases.

Battery Connector

Q392 L3 Service Manual

2) Restart / Hang

When the Power Key is pressed, the display freezes in a certain interface, if yes, Upgrade the software

version;

There is no display when the Power Key is pressed, and the current stays within 100~120mA, if yes, The

problem is caused by pseudo soldering or damage of the MCP (U501);carry out repair soldering or replacement of the

MCP;

There is heavy current when the Power Key is pressed, if yes, Find the hot point, and replace the

corresponding material (PMIC (U401) and CPU (U101) are damaged in most cases).

3) LCD Issues “Black screen and no display of LCD”

Solution:

Exchange the front shell to judge if the LCD itself is abnormal, if yes, Replace the LCD;

Check if the LCD connector is damaged (such as burnout) , if yes, Replace the LCD connector XJ801;

Check if the diode D802 in the backlight circuit is soldered abnormally or damaged, if yes, Carry out repair

soldering or replacement of D802;

Check if the power inductor L801 in the backlight circuit is soldered abnormally or damaged, if yes, Carry

out repair soldering or replacement of L801;

Replace the backlight driver IC (U801).

Q392 L3 Service Manual

Display problems such as black screen, white screen and blurred screen when the backlight is OK.

Solution:

Exchange the front shell to judge if the LCD itself is abnormal, if yes, Replace the LCD;

Check if the LCD connector is damaged, if yes, Replace the LCD connector XJ801;

Check if the EMI components (EMI801, EMI802, EMI803,EMI804) connected in series on the LCD MIPI

signal line are soldered abnormally or damaged, if yes, Carry out repair soldering or replacement;

Replace U101.

Q392 L3 Service Manual

4) Touchpad Failure

Solution:

Exchange the front shell to judge if the TW itself is abnormal, if yes, Replace the front shell (with LCD);

Check if the LCD/TP connector is damaged, if yes, Replace the main LCD/TP connector XJ801;

Replace U101

Replace Touchpad

5) Proximity Sensor “Test failure of the light/proximity sensor”

Solution:

Check if the silicon case for light/proximity sensor is properly installed, if yes, Reinstall the silicon case for

light sensor ;

Check if the sensor have damage or pseudo soldering, if yes, Replace the sensor;

Check if the I2C pull-up resistors of the acceleration sensor are OK, if yes, Carry out repair soldering of

resistors R306 and R307;

Replace U101 .

Q392 L3 Service Manual

6) Accelerometer “Failure to realize automatic screen rotation during image viewing”

Solution:

Check if the voltages of C900（1.8V）and C901（2.8V）, respectively, if yes, Carry out repair soldering or

replacement;

Check if the IIC pull-up resistors R306 and R307 of the acceleration sensor have pseudo soldering, if yes,

Carry out repair soldering or replacement;

Replace U908.

Q392 L3 Service Manual

7) Keypad

There is no current when the Power Key is pressed, or volume keys do not work, please exchange the key

FPC;

Check if R401,R1324 andR1325 is soldered abnormally or damaged, if yes, Carry out repair soldering or

replacement of them;

Check if ESD component FV1320, FV1321 and FV1331 are soldered abnormally or damaged, if yes, Carry

out repair soldering or replacement of them;

Replace U101

8) Charging Failures “No indication during charging”

Solution:

Check if the charging IC D402 is abnormal, if yes, Carry out repair soldering or replacement;

Check if the pull-up resistors R304 and R305 of the charging IC are abnormal, if yes, Carry out repair

soldering or replacement;

Check if the problem is solved after replacement of the PMU U401, if yes, It is problem of the PMU U401;

Replace the U101.

Q392 L3 Service Manual

There is charging indication, but no charging current.

Solution:

Check if there is any obvious damage on the surface of the charging IC U902, if yes, The charging IC is

damaged; replace U902;

Replace L407 and R328.

9) USB “Failure of Connecting the Phone to the PC via the USB Data Cable”

Solution:

Check if the connector XJ103 is damaged or has pseudo soldering, if yes, Carry out repair soldering or

replacement of the material;

Check if D401, FV109,FV110 are abnormally soldered or damaged, if yes, Carry out repair soldering or

replacement of the TVS tubes;

Replace U101.

10) Main Camera “Photographing and Shooting Failures”

Solution:

Check if the camera is properly installed, if yes, Reinstall it;

Exchange the camera to see if the problem is solved, if yes, The problem is caused by the camera itself;

replace it;

Check if the camera connector has pseudo soldering or damage, if yes, Carry out repair soldering or

replacement of XJ701

Check if the IIC pull-up resistors R302 and R303 have pseudo soldering, if yes, Carry out repair soldering or

replacement of R302 and R303.

11) Front Camera “Photographing and Shooting Failures”

Solution:

Check if the camera is properly installed, if yes, Reinstall it;

Exchange the camera to see if the problem is solved, if yes, The problem is caused by the camera itself;

replace it;

Check if the camera connector has pseudo soldering or damage, if yes, Carry out repair soldering or

replacement of XJ702;

Check if the IIC pull-up resistors R302 and R303 have pseudo soldering, if yes, Carry out repair soldering or

replacement of R302 and R303.

Q392 L3 Service Manual

12) Flash Light “Malfunction of Torch or Flashlight”

Solution:

Check if the camera can be turned on, if yes, The problem is caused by the rear-facing camera; see the

analysis of camera failures;

Check if the light can turn on when battery voltage is supplied to its both ends, if yes, Replace the light

HL902;

Replace U700.

13) Vibrator Failures

Solution:

Check if the vibrator has pseudo soldering or damage, if yes, Carry out repair soldering or replacement;

Replace U401.

Q392 L3 Service Manual

14) Sim “Failure to identify SIM card”

Solution:

Check if the SIM card sockets J1301andJ1303 is obviously damaged, if yes, Replace the SIM card socket;

Check if the pins of the SIM card sockets J1301andJ1303 have pseudo soldering, if yes, Carry out repair

soldering;

Check if the ground impedance of each pin of the SIM card sockets (except the ground pin) is low (lower

than grade K) , if yes, Replace U401;

Replace U401

15) Network /GPS / WI-FI “Weak signals of main antenna and GPS and WIFI antennas”

Solution:

Check the surfaces of the main antenna and the GPS and WIFI antennas to see if there is any

crease or breakage;

Check the gold fingers of the main antenna and the GPS and WIFI antennas to see if there is

any breakage and if the gold fingers are in good contact;

First, it is needed to check the matching parts of the main antenna and the GPS and WIFI

antennas to see if there is pseudo soldering or missing part, and check if the cables and the

corresponding sockets are in good contact.

Otros manuales para Q392

Tabla de contenidos

Otros manuales de Teléfono móvil de Micromax

Micromax

Micromax A093 Manual de usuario

Micromax

Micromax X512 Manual de usuario

Micromax

Micromax X252 Manual de usuario

Micromax

Micromax P580 Manual de usuario

Micromax

Micromax X266 Manual de usuario

Micromax

Micromax Q340 Manual de usuario

Micromax

Micromax A114 Manual de usuario

Micromax

Micromax A73 Manual de usuario

Micromax

Micromax X220 Manual de usuario

Micromax

Micromax Q346 Manual de usuario

Micromax

Micromax Q7 Manual de usuario

Micromax

Micromax X096 Manual de usuario

Micromax

Micromax X260 Manual de usuario

Micromax

Micromax Canvas Hue 2 A316 Manual de usuario

Micromax

Micromax Q5fb Manual de usuario

Micromax

Micromax A54 Manual de usuario

Micromax

Micromax X450 Manual de usuario

Micromax

Micromax Q2+ Manual de usuario

Micromax

Micromax A69 Manual de usuario

Micromax

Micromax X660 Manual de usuario

Micromax

Micromax A190 Manual de usuario

Micromax

Micromax E313 Manual de usuario

Micromax

Micromax Q427+ Manual de usuario

Micromax

Micromax X235 Manual de usuario

Manuales populares de Teléfono móvil de otras marcas

Zte

Zte BLADE A520 Manual de usuario

Nokia

Nokia Lumia 620 Manual de usuario

Blackbe;rry

Blackbe;rry KEYone Manual de usuario

Bea-fon

Bea-fon X5 Premium Manual de usuario

Blackbe;rry

Blackbe;rry 8707 Series Manual de usuario

Blackbe;rry

Blackbe;rry Storm Instrucciones de funcionamiento

LG LM-X420QN Manual de usuario

LifeWatch

LifeWatch V Manual de usuario

Bea-fon

Bea-fon SILVER LINE SL860 Manual de usuario

IKI Mobile

IKI Mobile KF4.5i Manual de usuario

Hitech

Hitech HT-850 Manual de usuario

Yezz

Yezz Fashion F10 Manual de usuario

Point Mobile

Point Mobile PM60 Manual de usuario

Blackbe;rry

Blackbe;rry Q10 Manual de usuario

Blackbe;rry

Blackbe;rry Bold 9900 Manual de usuario

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manual de usuario

LG LM-K420EMW Manual de usuario

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manual de usuario