7 8
Wet Cleaning:
Using the Cleaning Brush:
Switch the shaver off and ensure that the power cord is not
attached. Depress the foil screen assembly release buttons on
both sides of the unit and gently lift the foil screen assembly off.
(Figure 1)
Switch the shaver on and allow fresh, cold or lukewarm water to
run over the cutters. (Figure 2)
When finished cleaning, switch the shaver off and replace the
foil screen assembly, making sure it locks into place.
Switch the shaver off and ensure that the power cord is not
attached. Depress the foil screen assembly release buttons on
both sides of the unit and gently lift off the foil screen assembly
off. (Figure 1)
Gently brush the hairs from the inner cutters, the inside surface
of the foil screen assembly and the shaverʼs case. (Figure 3) To
remove the inner cutters for cleaning, gently lift straight up from
its mount. (Figure 4)
To clean the delicate outer foil screens, gently wipe the surface
of the foils with tissue paper, being sure not to apply a great
deal of pressure.
When finished cleaning, reseat the inner cutters on the mounts
and replace the hairpocket, making sure it locks into place.
Note: to ensure proper operation, the outer foil frame
assembly must be properly seated. To avoid damaging the
delicate foil screens, do not remove them from their frame.
To clean the trimmer, switch the shaver off and slide trimmer
upwards to deploy the trimmer. Gently brush the hairs from the
trimmer blades. (Figure 5)
This shaver should be cleaned with the brush provided after every
three wet cleanings.
NOTE: To avoid damage, be sure to thoroughly wipe pre-shave lotion
or shaver oil from the shaver's body.
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Cleaning the Head and Cutter Assembly:
Regular cleaning is necessary in order to maintain the optimal performance and maximum
comfort from the shaver. Wipe the shaverʼs body using a damp cloth and mild soap or
detergent. To avoid damaging the shaver, do not use harsh cleansers or solvents.
①
②
③
④
＊
①
②
③
Worldwide Voltage:
Recharging the Shaver:
This shaver features worldwide automatic dual voltage conversion for 100-240 volt,
50-60 Hz AC current. You can plug the power/recharging cord into an electric outlet
virtually anywhere in the world (an adapter plug may be necessary), and the shaver
will adjust automatically to the required voltage.
IS-3335 features a 5-stage LED power indicator. (figure 1)
Insure that the On/Off switch is in the “Off” position.
First, connect the power cord to the shaver and then plug it
into an electric outlet. (Figure 2)
During recharging, the LEDs will flash and then remain lit
as the unit recharges. Recharging generally takes one
hour. When fully charged, the shaver will provide
approximately one week of shaving run time.
When using the shaver for the first time or if the shaver has not been used for a
long time, charge the shaver for 16 hours.
Storing the Shaver and Power cord:
If the shaver is to remain unused for a long period of time, store the unit and power
cord in a cool, dry place. Do not wrap the cord around the unit during storage.
Avoid twisting the power cord. Be sure to unplug and untwist the cord if it becomes
twisted during use or while charging.
Fig. 2
①
②
5 Stage Power Indicator
Bottom LED Flashing - Recharging Required
LEDs Flash Sequentially and Then Lit - Shaver is Recharging
All LEDs Lit - Shaver is Fully Recharged
LEDs Light Sequentially - Shaver is Operating Normally
Fig. 1
WARNING! To avoid the risk of bursting and the subsequent release of toxic
materials, never mutilate or place the batteries in fire. To prevent acciden-
tal burns, avoid short-circuiting the batteries. Dispose of batteries in
accordance with local disposal / recycling requirements.
