( S ave ) indicator light off means the
:.. :. : -::e. ransnil mode. I E I
sr.G El tr .{€:tr €tt m l]Ens the devi@ is under
i B c n€n speed syrc mode, A/B/C buttons on
.. - . IlEos dtput signal function properly.
srl',. E E
ABC
IEI indicator light on means the device
is under2nd curtain.
Remark: Wireless trigger work only when the transmitter and
receiver with the same group light on, e.g. the transmitter with
A group Iight on. receiver with A group light on so the device is
able to trigger the flash otherwise, it is unable to trig the flash
properly. Transmitter maximum controlling 3 groups at the
same time and each group is able to control more than one flash
at the same time.
1. Multi-button design, each function with individual button when
make the operation more simple
2- Support firmware update
3. With farlher controlling distance, 200 meters with normal
operation, maximum with 500 meters in open area.
4. With more combinations of output model, able to set each
group offlash with differeni output power
5. With Iess pcre'cc-sirption design and using gold plated
balter! compafrmea:.
6 With exlenoabie syac aulpJ: sac(et 1c: cil] abie tocont.ol
€rera si:@ting but also able to co.iic cuidoor flasi igii and
siudrc iighr
7. With artificial design of testing output pder
8. Support group controlling offlash focusing
1 Car se: :ie exposure compensation, bracket exposure, aperture
and f@l length through the camera setting.
2. Also 6n set the above functions through the flash setting
A. TTL mode and manual mode which need to set on flash setting
if never set the focal length on flash setting then you have to
reset the camera to be auto mode and set the focal length as
auto on the flash setting.
B. Focal Iength setting, the flash setting have priority on the focal
length output, if never set the focal length on flash setting then
you have to reset the camera to be auto mode and set the focal
length as auto on the flash setting.
C. The flash output of test flash is according the flash setting. e.g
whenever the flash set as TTL mode, the ilash output of test
flash which is according tothe pre-flash output; wheneverthe
flash set as manual mode, the flash output oftest flash which
is according to manual setting.
Work as flash trigger
1. Check the installation; tum on the power ofiash, GmeE and receiver
2. Half-press the shutter button of the €mera, @mera willfocus. lf the
flash is under standby condition, it will be awakened.
3. Full-press the shutter button ofthe @mera, it will take the photo, and
the flash will be triggered.
4. Make sure the transmitter efiective @ntrcl grcups inc{ude @iver
current group, otheryise the receiverwill not be triggered.
5. Wake-up function is not supported when using the incomp-atible
transmitter The first image sync speed will be reduced;the second
image shooting in 30sec will be back to normal sync speed.
Control studio light
You can purchase additional 3.5mm-3.5mm studio flash cable,3.55 to
6.35 adapter, 3.5mm to 6.35mm studio flash cable. Receiver get
trigger signal can sync trigger studio light by additional flash cable.
Control multi flash
You need to purchase additlonal triggerflash eble, which can @ntrol
multi pass through, studio light or mix using the two kinds of flash, to
sync lrigger all the flash when shooting.
'1. lnstall the pass through flash on receiver hot shoe socket.
2. Connect receiver and studio light with connecting cable.
3. lnstall transmitter on the top hot shoe of camera, full press camera
release button, all the flash will sync flash with camera.
4. Need matching cfiannel wih all he l@ive6 and haremitt€r before using.
You need to pruchase additional flash cable to using this function. We
have many kinds of flash cable and can fit almost all the market
popular DSLR camera.
1. lnsert flash cable plug into receiver output socket.
2. lnsert flash cable another plug into camera shutter socket.
Remark: when using RF-624 as the shutter remote, please don't
mount the device on top of the camera's hot shoe otherwise the
devices would not be function properly.
Due to the difference shutter of the camera, the shutter remote is
unable to function under the auto focus mode for some brands of
camera. lt can only function under manual focus mode.
ffiffiffi
1 - Check the camera's hot shoe weather is the same as the tra nsceiver
2. Putthe transceiver as diagram 1-2 as thearrowdirectionon
top of the camera
3. After mou nted the transceiver on camera, follow diagram 1 -3
arrow direction and fixed the screw.
Thanks for purchasing Meyin product and read this instruction
manual.
You can contact Meyin local distributor if you have any question
or justvisit Meyin official website:
hltp: / /www. meyin. com. cn
This manual information is updated at April, 131h,2013. You
need ask Meyin distributor for details if you want to use this
manual with the product which release later.
MSM006 V10.01
