MEWOI MEWOI6100 Manual de usuario
Digital Earth Resistance Tester
MEWOI6100，MEWOI7800E
User Manual
www.mewoi.com
CONTENT
Warning...................................................................................................1
I Introduction...........................................................................................2
II Electrical Signs ...................................................................................3
ⅢTechnical Specifications ..................................................................4
ⅣStructure............................................................................................7
V LCD Display.....................................................................................8
VI Operating Method.............................................................................8
1. Start-up, Shutdown.......................................................................8
2. AC/DC measurement switch ........................................................9
3. DC Calibration..............................................................................9
4. Current Measurement.................................................................10
5. Peak Holding..............................................................................12
6. Hold, Storage and Access Reading.............................................12
7. Data Upload................................................................................13
ⅦHow to Change Battery.................................................................14
ⅧAccessories ...................................................................................14
-1-
- 2-
Warning
Thank you for purchasing our company's MEWOI7100/MEWOI7800E
AC/DC Clamp Leaker, for better use of this product, please:
——Read carefully the user's manual.
——Follow strictly safety rules and notes listed in this manual.
Under any circumstances, please pay special attention to your safety in
the course of using this leaker.
Give heed to label texts and symbols on panel and back plate of this
leaker.
Please be more careful if the line voltage is above 60VDC or 30VAC.
Put the tested wire through the geometrical center of jaw when measuring
AC current, error will increase if deviate the center.
Please don't place and store this leaker in hot and humid condition,
locations with moisture condensation and under direct sunlight for a long
time.
In case voltage of battery was low, please replace batteries.
In case this leaker would not be used for a long time, please take out
batteries.
-2-
When changing batteries, please pay attention to polarity of battery.
Use, disassembly and maintenance of this leaker shall be operated by
authorized personnel.
In case dangers would have with continues use of this leaker, please stop
to use it and seal it for safekeeping immediately; and then, send it for
disposal of authorized agency.
Users shall carry out operation based on danger signs “ ” on leaker
and manual.
Users shall carry out safety operation based on instructions listed in this
manual, e.g. “ ” and danger signs on this manual.
Please use am to test leakage current (test by clamping grounding line,
single-phase line together).
I Introduction
MEWOI7100 /MEWOI7800E AC/DC Clamp Leaker is specially designed
for measurement of AC/DC current below 600V; by adopting up-to-date CT
technology and digital integration technology. There is no exposed metal on
clamp head, non-contact measurement, to ensure safe operation. It is a
product with relatively small size, high accuracy and perfect function
compared with similar leakers in the world. The leaker could be widely applied
-3-
in those fields as electricity, communications, meteorology, railroad, oilfield,
construction, measurement, scientific & research teaching institutes, industrial
and mining establishments. It is an essential tool for electrician safety testing
MEWOI7100/MEWOI7800E AC/DC Clamp Leaker has those functions as
peaking holding, data holding and data storage. It obtains one RS232 or USB
interface, communication cable and monitoring software, through which
on-line monitoring, historical data inquiry is available. It also have functions
such as active curve drawing, indication of max, min and average value, alarm
setting and indication, saving to documents and printing when connected to
PC.
II Electrical Signs
Extremely dangerous! Operators shall strictly observe safety
rules; otherwise there would be dangers of electric shock to
cause personal injuries or casualties.
Dangerous！Operators shall strictly observe safety rules;
otherwise there would be dangers of electric shock to cause
personal injuries or casualties.
Warning ！Operators shall strictly observe safety rules;
otherwise personal injuries or equipment damages might be
-4-
caused.
Double insulation
AC
DC
ⅢTechnical Specifications
Model
MEWOI7100
MEWOI7800E
Size of clamp
30mm×35mm
Φ68mm
Range
0.0A~1000A DC/AC
DC:0.0A-2000A
AC:0.0A-1500A
Accuracy
±2%rdg±3dgt
±2%rdg±3dgt
Resolution
0.1A
0.1A
Dimension
175mm×70mm×38mm
224mm×115mm×43mm
Data interface
RS232
USB
Weight
180g(with battery)
515g(with battery)
Function
Measurement of AC/DC current, Peak value hold,
On-line monitoring
Power Supply
Zn-Mn dry battery 6F22 9V，lasting for100hours
-5-
Test Mode
Clip-on CT, integral mode
Display Mode
Four digits LCD display
LCD
Dimension
35mm×21.5mm；display domain：32mm×15mm
Frequency
AC 45Hz~400Hz
Sampling
Rate
2 times/s
Polarity
Indication
DC current auto identified and display“—”
Test Position
Tested wire in the jaw center; Error will increase to
1.5%rdg max if deviate the center
Range Shift
Automatically
Line Voltage
AC600V
Software
with the software the data can upload to computer
Data Memory
99units，FULL blinks when the memory is full
Peak Hold
Push HOLD without release, the meter will show the
peak value during the pushing period
Reading Hold
DH indicating the reading is hold
Out of Range
OL indicating the current is out of range
-6-
(Condition: 23℃±5℃，below 75%rh,wire in the center of jaw)
Auto
Power-off
5 Minutes after power on, it will power off
automatically to lower the power consumption
Battery
Voltage
Indicating the battery voltage is lower than
7.2V.Then the battery have to be changed
Consumption
10mW
Temperature
and Humidity
-10℃~50℃；Below 80%rh
Max error
refer to
environment
-10℃~0℃,40℃~50℃,Error will increase max to
1%rdg
Temperature
and Humidity
for storage
-10℃~60℃,below 70%rh
Insulating
Strength
AC2kV/rms. (between the alloy of the clamp and the
housing)
Applicable
safety rules
IEC1010-1, IEC1010-2-032, Pollution level 2, CATⅢ
(600V)
-7-
ⅣStructure
MEWOI7100 MEWOI7800E
1. Double input toroid 2. Toroid opening lever
3. POWER key 4. LCD
5. RS232 interface 6. Positive direction
7. HOLD Key 8. AC/DC switch key
9. DCA ZERO Adjust 0 key 10. Housing Screws (3 PCS)
-8-
11. Battery cover screw 12. Battery cover
VLCD Display
1. DC indication 2.AC indication
3. Negative polarity indication
4. Low battery symbol
5. Data hold indication
6. Stored data code
7. Unit of current indication
8. Value of current
VI Operating Method
1. Start-up, Shutdown
Press POWER key to start up, LCD will begin to display; Press the
POWER key again, the leaker will shut down. After starting up for 5
minutes, LCD will flick notes that the leaker will shut down automatically;
after flickering for 30s, it will shut down formally to reduce battery
consumption. In case you have pressed POWER key when LCD was
flickering, the leaker will continue to work for 5 minutes. If LCD was very
dark after starting up, it might be caused by low-voltage battery, in this
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Otros manuales de Equipo de prueba de MEWOI
MEWOI
MEWOI MEWOI4000 Manual de usuario
MEWOI
MEWOI MEWOI-HLY200A Manual de usuario
MEWOI
MEWOI MEWOI-UCT-C Manual de usuario
MEWOI
MEWOI MEWOI3000+ Guía del usuario
MEWOI
MEWOI MEWOI-PTS400 Manual de usuario
MEWOI
MEWOI MEWOI-PTS250 Manual de usuario
MEWOI
MEWOI MEWOI1500D Manual de usuario
MEWOI
MEWOI MEWOI68C Manual de usuario
Manuales populares de Equipo de prueba de otras marcas
SMART
SMART KANAAD SBT XTREME 3G Series Manual de usuario
Agilent Technologies
Agilent Technologies BERT Serial Manual de usuario
Agilent Technologies
Agilent Technologies N3280A Manual de usuario
Vernier
Vernier Go Direct Voltage Manual de usuario
Lifeloc
Lifeloc R.A.D.A.R. Manual de usuario
Fluke
Fluke T5-600 Instrucciones de funcionamiento e instalación
