Metra Electronics 99-7367 Manual de usuario
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 11/21/17 INST99-7367
INSTALLATION INSTRUCTIONS
99-7367
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Factory clock and push to start provision
• 99-7367B - Painted matte black
• 99-7367HG - Painted gloss black
KIT COMPONENTS
• A) Radio housing trim panel • B) Radio brackets • C) Vent trim ring • D) Pocket • E) Start/Stop switch blank plate • F) Storage pocket
• G) (8) #8 x 3/8” Phillips screws
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ...............................................2-3
Kit Preparation .......................................................4
Kit Assembly
– ISO DIN radio provision with pocket .................5
– ISO DDIN radio provision ....................................6
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-7304
Antenna Adapter: Not required
A B C D E F G
Kia Rio 2016-2017
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove the factory radio trim
panel including the a/c vents. (Figure A)
Note:
Remove the (8) retaining clips to
be reused in Kit Assembly.
2. Remove (4) Phillips screws securing the
radio in the dash.
Continued on the next page
(Figure A)
REV. 11/21/2017 INST99-7367 3
DASH DISASSEMBLY (CONT)
3. Remove (2) Phillips screws securing the
start/stop switch if equipped. (Figure B)
4. Remove (4) Phillips screws securing
the storage pocket, or factory clock if
equipped. (Figure B)
5. Remove the (6) Phillips screws securing
the a/c vents then unclip and remove
them from the radio trim panel.
(Figure B)
6. Unclip and remove the hazard switch.
(Figure B)
Continue to Kit Preparation
(Figure B)
Step 3
Step 4
Step 5
Step 6
1.800.221.0932
|
MetraOnline.com
4
KIT PREPARATION
1. Place the
vent trim ring
into the
radio
housing trim panel
and mount the vents
using the factory screws removed in
disassembly. Mount the clock and hazard
switch into the
radio housing trim panel
using screws removed in disassembly.
(Figure A)
Note:
If no factory clock is present,
a storage pocket and (4) # 8 x 3/8”
Phillips screws are provided.
2. Secure the
start/stop switch
or
blank
plate
depending on your application
into the
radio housing trim panel
.
Note:
If no switch is present there are
(2) #8 X 3/8” Phillips screws supplied
to mount the blank plate.
3. Install the (8) panel clips removed in
disassembly onto the
radio housing trim
panel
.
Continue to Kit Assembly (Figure A)
REV. 11/21/2017 INST99-7367 5
KIT ASSEMBLY
(Figure A) (Figure B)
ISO DIN radio provision with pocket
1. Secure the
pocket
to the
radio brackets
with the (2) #8 x 3/8” Phillips screws
supplied. (Figure A)
2. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
3. Slide the radio between the
radio
brackets
and secure with screws
supplied with the radio. (Figure B)
4. Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Test the radio for proper
operation.
5. Reassemble the dash in reverse order of
disassembly.
1.800.221.0932
|
MetraOnline.com
6
KIT ASSEMBLY
(Figure A)
ISO DDIN radio provision
1. Secure the
radio brackets
to the radio
with the screws supplied with the radio.
(Figure A)
2. Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Test the radio for proper
operation.
3. Reassemble the dash in reverse order of
disassembly.
REV. 11/21/2017 INST99-7367 7
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before
doing so, look over the instructions a second time, and make
sure the installation was performed exactly as the instructions
are stated. Please have the vehicle apart and ready to perform
troubleshooting steps before calling.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 11/21/17 INST99-7367
INSTALLATION INSTRUCTIONS
99-7367
¡PRECAUCIÓN! Todos los accesorios, interruptores,
paneles de controles de clima y especialmente las
luces del indicador de las bolsas de aire deben estar
conectados antes ciclar la ignición. Además, no
quite el radio de fábrica con la llave en la posición o
de encendido ni con el vehículo funcionando.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 11/21/17 INST99-7367
INSTRUCCIONES DE INSTALACIÓN
99-7367
KIT FEATURES
• Provisión de radio ISO DIN con cavidad
• Provisión de radio ISO DDIN
• Reloj de fábrica y provisión de botón de arranque
• 99-7367B - Pintura de negra mate
• 99-7367HG - Pintura negro brillante
COMPONENTES DEL KIT
• A) Panel de la moldura de la carcasa del radio • B) Soportes del radio • C) Anillo de moldura de las rejillas • D) Cavidad
• E) Placa vacía del interruptor de inicio/paro • F) Bolsillo de almacenamiento • G) (8) Tornillos Phillips #8 de 3/8”
HERRAMIENTAS REQUERIDAS
• Herramienta para quitar paneles
• Destornillador Phillips
INDICE
Desmontaje del tablero .....................................2-3
Preparación del kit .................................................4
Ensamble del kit
– Provisión de radio ISO DIN con cavidad ............5
– Provisión de radio ISO DDIN ...............................6
A B C D E F G
Kia Rio 2016-2017
CABLEADO Y CONEXIONES DE ANTENA
(se venden por separado)
Arnés de cables: 70-7304
Adaptador de antena: No requerido
1.800.221.0932
|
MetraOnline.com
2
DESMONTAJE DEL TABLERO
1. Desenganche y quite el panel de la
moldura del radio de fábrica, incluyendo
las rejillas del aire acondicionado.
(Figura A)
Nota:
Quite los (8) ganchos de retención
que se volverán a usar en el ensamble
del kit.
2. Quite los (4) tornillos Phillips que
sostienen el radio en el tablero.
Continúa en la siguiente página
(Figura A)
Otros manuales para 99-7367
1
Tabla de contenidos
Idiomas:
Otros manuales de Soporte de TV de Metra Electronics
Metra Electronics
Metra Electronics TL64 Manual de usuario
Metra Electronics
Metra Electronics TX86 Manual de usuario
Metra Electronics
Metra Electronics 95-3005 Manual de usuario
Metra Electronics
Metra Electronics 99-5832G Manual de usuario
Metra Electronics
Metra Electronics 99-5831 Manual de usuario
Metra Electronics
Metra Electronics 108-FD9B Manual de usuario
Metra Electronics
Metra Electronics 99-9223 Manual de usuario
Metra Electronics
Metra Electronics 99-7614 Manual de usuario
Metra Electronics
Metra Electronics 107-GM3B Manual de usuario
Metra Electronics
Metra Electronics 99-5600 Manual de usuario
Metra Electronics
Metra Electronics 95-7802CH Manual de usuario
Metra Electronics
Metra Electronics 99-5830B Manual de usuario
Metra Electronics
Metra Electronics 95-8734 Manual de usuario
Metra Electronics
Metra Electronics DP-7363B Manual de usuario
Metra Electronics
Metra Electronics 95-8910S Manual de usuario
Metra Electronics
Metra Electronics 99-3022B Manual de usuario
Metra Electronics
Metra Electronics 95-7815B Instrucciones de uso
