MERYTRONIC ARIADNA ILF-12 Manual de usuario

ARIADNA ILF-12

PHASE AND FEEDER

IDENTIFIER

USER GUIDE V 3.0

INDEX

1. SYSTEM DESCRIPTION........................................................................................................6

1.1. COMMUNICATION BETWEEN CD AND LD IN AUTOMATIC MODE ..........................7

2. EQUIPMENT CONTENTS......................................................................................................8

3. DEVICE DESCRIPTION.........................................................................................................9

3.1. CENTRAL DEVICE CD ..................................................................................................9

3.2. LINE DEVICE LD..........................................................................................................10

4. CENTRAL DEVICE (CD) EQUIPMENT CONNECTION ......................................................11

4.1. STAR TRANSFORMER: 3 PHASE + NEUTRAL LV OUTPUT....................................11

4.1.1. LD DEVICE CONNECTION POINT PHASE-NEUTRAL: .......................................12

4.1.1.1. STEP ONE: CONNECT SENSOR RINGS TO FEEDERS................................12

4.1.1.2. STEP TWO: CD SUPPLY CABLE CONNECTION...........................................13

4.1.1.3. STEP THREE: SELECT WORKING MODE, AUTO-FN OR MAN-FN MODES15

4.1.3. LD DEVICE CONNECTION POINT PHASE-PHASE:............................................20

4.2. DELTA TRANSFORMER: 3 PHASE LV OUTPUT (NO NEUTRAL)............................21

4.2.1. LD DEVICE CONNECTION POINT PHASE-PHASE:............................................22

4.2.1.1. STEP ONE: CONNECT SENSOR RINGS TO FEEDERS................................22

4.2.1.2. STEP TWO: CD SUPPLY CABLE CONNECTION...........................................23

4.2.1.3. STEP THREE: SELECT WORKING MODE, AUTO-FF OR MAN-FF MODES...25

5. LINE DEVICE (LD) CONNECTION ......................................................................................30

5.1. PHASE TO NEUTRAL NETWORK POINTS (STAR, B1 WITH NEUTRAL OR B2):......30

5.2. PHASE TO PHASE NETWORK POINTS (DELTA OR STAR B1 WITH NO NEUTRAL

AVAILABLE):..........................................................................................................................31

6. IDENTIFICATION PROCESS...............................................................................................32

6.1. AUTO MODE...................................................................................................................32

6.2. MAN MODE.....................................................................................................................37

7. TIPS......................................................................................................................................39

8. TECHNICAL FEATURES .....................................................................................................41

9. QUALITY STANDARDS AND SECURITY ...........................................................................43

10. WARRANTY AND TECHNICAL SERVICE ........................................................................44

Safety information, read these indications first:

Used symbols:

Earth terminal

Caution, check the user guide explanation

European conformity

Supply cable connection to mains is OK

Error on supply cable connection to mains

CAT III measurement category: makes reference to the distribution level and

permanent circuits inside a building

Ariadna Network Identifiers meet European Low Voltage Directive 72/23/CEE and are

compliant with:

- Central Device: EN 50178 (Electronic equipment for use in power installation)

- Line Device: EN 61010-1 CATIII

Read the complete user guide before using the equipment and its accessories.

Avoid working alone

Do not use the equipment in gas or explosive vapor areas.

Before using the equipment check cables and coils to see if there is any

mechanical damage; if so replace them. Try to locate breaks or missing plastic

components. Pay special attention to the isolating material that surrounds

connectors.

Disconnect all sensors, cables and accessories that are not being used.

Use the earth connection to connect the equipment to ground and do not

apply voltage.

Do not apply voltages above the nominal working voltage of the equipment.

Before use, check the voltage level coincides with the supply voltage and frequency.

In case of security functions deterioration:

If the equipment is used in a way not specified by the manufacturer, its protections

could become affected.

Before use, check cables and rest of accessories to make sure they are not

damaged; replace them if necessary.

If the equipment or its accessories are damaged or do not work properly, do not use

them and send them for repair.

1. SYSTEM DESCRIPTION

The purpose of this equipment is to achieve the maximum possible information

regarding the low voltage network topology. This means knowing the

connectivity of each accessible point of the LV network.

In this document connectivity is defined as the existing connection relationship

between a network point that is being analyzed, and the MV/LV transformer

substation, feeder and phase that feeds it.

Ariadna ILF12 equipment consists of two devices: Central Device (CD) that is

installed in the MV/LV transformer substation that supplies electricity to the area

whose topology is being achieved, and the Line Device (LD) that is carried by

the operator along the network points whose connectivity is being analyzed. The

CD and the LD communicate with each other using the electric distribution

network.

1.1. Communication between CD and LD in Automatic Mode

1st

2nd

INFORMATION

CD injects phase and CD

number identification

signals through each

phase of the MV/LV

transformer.

If the network point where the LD is

connected to belongs to the same

MV/LV transformer, it will receive data

info, which will be shown on the LCD

display.

INFORMATION

After receiving

phase and CD

number, it will

transmit a signal

upstream towards

the transformer.

CD receives this signal

through the sensor ring that

corresponds to the feeder

where the LD has been

connected to.

This way MV/LV transformer, feeder and phase

connectivity information is clearly identified.

4th

3rd

INFORMATION

CD identifies the

corresponding feeder

and injects its

identification result code

towards LD.

Receives feeder

identification signal

injected by CD and

displays this

information.

2. EQUIPMENT CONTENTS

Ariadna ILF12 equipment consists of:

-CD: Central Device that can identify up to 3 phases and 12 feeders

-12 Sensor Rings (Rogowski Coils)

-5 core supply cable to connect the CD to the transformer LV busbar

-LD: Line Device (UL-220) with graphic display.

-LD soft case

-Two cables, red (phase) and blue (neutral) to connect the device to the

network points to be analyzed.

-Spare fuse box.

-4 AA 1.5V batteries.

-User guide.

-Equipment soft bag.

3. DEVICE DESCRIPTION

3.1.Central Device CD

Power ON

Power OFF

UC Number Selection

Automatic / Manual mode selection

UC restart

3.2. Line Device LD

Tabla de contenidos

Manuales populares de Sensor de seguridad de otras marcas

THORLABS

THORLABS PDA10JT Manual de usuario

Waeco

Waeco UV-DETECT Manual de usuario

Intermatic

Intermatic IOS-DSIMF Manual de usuario

urmet domus

urmet domus 1083 Manual de usuario

Siemens

Siemens AZL66 Series Manual de usuario

BTI

BTI Profiline Multi Finder Manual de usuario

Challenger

Challenger SL01 Manual de usuario

DMP Electronics

DMP Electronics 1122INT Manual de usuario

Rielta

Rielta Ladoga MK-RK Manual de usuario

Mirion Technologies

Mirion Technologies ACCURAD PRD Manual de usuario

Bosch

Bosch DS835 Manual de usuario

DBI SALA

DBI SALA EZ Stop Manual del operador

Lamptime

Lamptime ST05C Manual de usuario

Ubiquiti

Ubiquiti MFI-MSC Manual de usuario

Subsite

Subsite 910R Instrucciones de instalación

Satel

Satel OPAL Pro Manual de usuario

Aleph

Aleph XC-1XTEU Manual de usuario

Pima

Pima LARIS QUAD Manual de usuario