Mercury Security SR-10A Manual

SR-10A Stand-Alone Access Control System

www.mercury-security.com

2355 MIRA MAR AVE. LONG BEACH, CA 90815-1755, (562) 986-9105, FAX (562) 986-9205

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2)

thisdevicemustacceptanyinterferencereceived,includ-

ing interference that may cause undesired operation.

The SR-10A is designed to read a specified number of digits from a magnetic stripe card

and can accept up to 100 combinations of those digits.

Setup

Step 1: Decide How Many Digits to Read

The first step is to tell the reader how many digits to read

from the card. This is done by using J2 jumpers 1-3. Using

the table on the right, set J2 jumpers 1-3 to the appropriate

setting. Remove J2 jumpers 1 through 3 for "ATM" mode,

grants access to any card with data on track 2.

Step 2: Set Door Strike Timing

There are two door strike durations that are selectable by J2

jumper 4. When the J2 jumper 4 is "IN", the strike duration

is 5 seconds. When J2 jumper 4 is "OUT", then the duration

is 1 second.

Nowthereaderisreadytoacceptcardinformation.

Card Maintenance

Enrolling New Card(s) to the System

Toenrollanewcardintothe SR-10A, perform thefollowingsteps:

1. RemoveJ2 jumper 6. Onceremoved,the LED onthereader flashes green.

2. Swipe each card to be enrolled, the reader will beep two times for each good card read.

3. ReinstallJ2 jumper 6 after enrolling card(s). The LED on thereader will turn red and the reader will beepthree

times.

Thereaderisnowreadytobe used.

Jumper 1 Jumper 2 Jumper 3 # of Digits

OUT OUT OUT 0

IN OUT OUT 1

OUT IN OUT 2

IN IN OUT 3

OUT OUT IN 4

IN OUT IN 5

OUT IN IN 6

IN IN IN 7

J2 Jumper # Description

1-3 Select Number of Digits

to Read on Card

4 Strike Relay Duration

5 Not Used

6 Enroll Cards

7 Not Used

8 Delete All Cards

DeletingtheCardDatabase

Todeletethecardholderdatabase,performthefollowingsteps:

1. Removepowerfrom the unit and install J2 jumper 8.

2. Apply power for 5 seconds, LEDs A and B ON, and then remove power.

3. RemoveJ2jumper8andreconnectpower.

The card database is now empty. You must then re-enroll your cards.

Note:IntheATMmode,enrollinganddeletingcardsisnotrequired.

CONFIDENTIAL: For installation and maintenance use only. DO NOT distribute.

Exit Request

Door Contact

Strike

Forced Open,

Held Open

Alarm Buzzer

TB2

GND

VIN

TB3

K1 K2

GND (BLK)

BZR (ORG)

LED (BRN)

CLK (WHT)

DAT (GRN)

12V (RED)

PIN 1

12345678

TB1

GND

TR-

TR+

DAT

GND

LED

DAT

BZR

TB4

TB3

TB2

GND

VIN

K2K1

J2 JUMPERS

4.25 [108.0]

3.85 [97.8]

2.35 [59.7]

2.75 [69.9]

Ø.156 [Ø3.96]

.2 [5.08] .2 [5.08]

Reader Configuration Setting and Installation

Find a suitable location to anchor the reader mounting bracket. The mounting of the reader does not

require a junction box. However, rigid conduit is required for outdoor application. A single gang

junction box may used to provide transition to rigid conduit. If a single gang junction box is used, a

wallplate(optional)maybeusedtocoverthejunctionbox.Thereaderisthensecuredtothemounting

bracket using a screw. Refer to figures for reader dimensions and typical junction box usage.

Connectdoorhardware/poweraccording to the configuration selected. Wires of 22AWG or larger are

recommended for field wiring. See local electrical code.

Coatreader connector with the silicone greasesuppliedto seal out moisture foroutdoormounting.

FOR 24Vac STRIKE, PANASONIC ERZ-C07DK470

MOV SELECTION:

VOLTAGE RATING > Vac RMS

DIODE SELECTION:

DIODE CURRENT RATING > 1X STRIKE CURRENT

DIODE BREAK DOWN VOLTAGE : 4X STRIKE VOLTAGE

DIODE 1N4001 (50V/1A) TYPICAL

Toavoid havingESD(electrostaticdischarge)interferingwiththeoperationofthereader,thereadercasing

shallbegrounded.Thiscanbeaccomplishedbetyingthemountingbrackettoearthgroundlocally(e.g.

groundedconduit). Thereaderhasa fourdipswitchblockwhichmustbeconfigured. Allfour switches

must be in the OFF position. When looking into the back of the reader, all switches should be pushed

away.

Reader Part Number: 36012-0000

Reader DIP switch setting: 4 3 2 1

(FactorySetting) OFF OFF OFF OFF

Relay Contact Protection/Noise Suppression

Load switching can cause contact transfer, welding, and abnormal wear, which can cause premature

contact failure. The switching of an inductive load (strike) can also cause EMI (electromagnetic

interference).Toprolongcontactlifeandincreasetotalsystemreliability,contactprotectioncircuitmust

be used. The following two circuits are recommended: For DC application, use a diode circuit; for AC

application, use a MOV (metal oxide varistor) circuit. Locate the protection circuit as close to the load

as possible, as the effectiveness of the circuit will decrease if it is located too far away. As a guideline,

the distance should be within 12 inches (30 cm).

+−

GND

VIN

TB3

AC AC STRIKE

GND

VIN

TB3

AdditionalInformation

1. TheLED'sontheinterfaceboardaredefinedas:A=Heartbeat:1secondflash,A&BON=Deleting

card database.

2. OutputK2isenergizedfor1secondwhenthereisadoorforcedopenordoorheldopenalarm. The

door position is monitored by input I1 and the door monitor contact is normally closed. The held

open timer is fixed at 45 seconds.

3. Request-to-exit(REX)inputI2:usesanormallyopenswitch. OutputK1isenergizedaslongasthe

REX input (I2) is closed.

4. Jumpers J3 and J4 are not used.

Maintenance

The SR-10A readers are designed to provide continuous service with minimal routine maintenance.

However, contaminants (such as magnetic oxides from badges and dirt) tend to accumulate on the

read head. Without regular cleaning, these contaminants will shorten the read head life and increase

the probability of card read error. A maintenance schedule should be developed base on the card

reader environment (dirty or clean) and the usage frequency (light traffic or heavy traffic). Extreme

case may require daily cleaning.

Headcleaning may be done byusingdisposable, pre-saturated magnetic head cleaningcard.These

cards are readily obtainable from a number of sources (e.g. Clean Team Co., www.cleanteam.com,

800-888-8830;KICProducts,www.kicproducts.com,207-514-7030;SystemID,www.systemid.com,

888-648-4452).

The reader exterior surface is covered with high strength polymer and polyester membrane. It may

be cleaned with a soft cloth and mild detergent if required.

Specifications

The reader/Interface are for use in low voltage, class 2 circuits only.

Electrical: Voltage 12 Vdc (10.2 to 13.8 Vdc)

Current 200mA

Relay K1, 5A@30Vdc; K2, 1A@30Vdc

Mechanical: Reader:

Dimension 1.95"(50mm)W x 1.30" (33mm)H x 5.50" (140mm)L

Weight 10oz.(284g)nominal

Interface:

Dimension 4.25" (108mm)W x 2.75" (70mm)L x .75" (19mm)H

Weight 2.8 oz. (80 g) nominal

Environmental: Temperature: -55 to +85 degrees C, storage

-40to+75degreesC,operating

Humidity: Reader- 100% RHNC; Interface- 95% RHNC

WARRANTY

Mercury Security Corporation warrants that the product is free from defects in material and workmanship under

normal use and service for two years from factory shipment. Mercury Security Corporation assumes no

responsibility for products damaged by improper handling or installation. This warranty is limited to the repair or

replacement of the defective unit.

There is no expressed warranties other than set forth herein. Mercury Security Corporation does not make,

intends, nor does it authorize any agent or representative to make any other warranties, implied warranties, and

expressly excludes and disclaims all implied warranties of merchantability of fitness for a particular purpose.

Returned units are repaired or replaced from a stock of reconditioned units. Returns must be accompanied by a

return authorization number obtained from customer service, a purchase order and prepaid postage.

LIABILITY

The card readers should only be used to control exits from areas where an alternate method for exit is available.

This product is not intended for, nor is rated for operation in life-critical control applications. Mercury Security

Corporation is not liable under any circumstances for loss or damage caused by or partially caused by the

misapplication or malfunction of the product. Mercury Security Corporation's liability does not extend beyond the

purchase price of the product.

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario