Merco CONTEMPO SERIES Guía de inicio rápido

Contempo

Lamps Service Manual

PARTS & SERVICE MANUAL

for

CONTEMPO SERIES

WARMER LAMPS

Merco Contempo Warmer Lamps offer graceful, dramatic styling to match any décor. They are made

of exacting tolerance from heavy duty, solid, mandrelspun aluminum for durability, but like any piece

of equipment with moving parts, physical wear takes its toll. When this happens, the information in

this manual will prove helpful. Although the instructions are easy to follow, the work should be

handled by a qualified Merco Certified Service Technician.

THIS MANUAL SHOULD BE RETAINED FOR FUTURE USE

ContempoServMan REV: B – 8/10/07

Contempo Lamps Service Manual

CONTEMPO – STYLE A

COMMON TO ALL STYLE A

ITEM PART # DESCRIPTION QTY

1 000688 Sticker, M. Contempo, UL/NSF 1

2 060434 Bar, Combination, Bracket 1

3 000178 Bushing, Snap, HEYCO 1

4 000717 Switch, Toggle 1

5 000430 Nut, 6-32, HEX, Z 2

6 000828 Washer, Lock 1

7 000671 Socket, Porcelain 1

8 000449 Nut, 1/8 IPS x 9/16, Panel, Z 2

9 000597 Screw, 8-32 x ½”, PHP 2

10 000429 Nipple, 1/8 x ½ W Hex Nut, BRS 1

11 000469 Wirenut 1

12 000417 Nipple, 3 ½”, Brass 1

VARIABLE

ITEM PART # DESCRIPTION QTY

13 --- Canopy 1

14 --- Stem 1

15 --- Ring, Check 1

16 --- Shade 1

17 --- Lamp, 120V, 250W 1

18 --- Swivel 1

For all parts not listed, call factory

Contempo Lamps Service Manual 3

CONTEMPO – STYLE C

COMMON TO ALL STYLE C

ITEM PART # DESCRIPTION QTY

1 000688 Sticker, M. Contempo, UL/NSF 1

2 060434 Bar, Combination, Bracket 1

3 000178 Bushing, Snap, Heyco 1

4 000717 Switch, Toggle 1

5 000430 Nut, 6-32, Hex, Z 2

6 000828 Washer, Lock 1

7 000175 Bushing, Bake Lite, ¼” IPS/FEM 1

8 000592 Screw, 8-32 x ¼”, PHP 2

9 000174 Bushing, Snap, Shorty 1

10 000345 Hickey 1

11 001550 Clamp, 2 Ear, Zinc 1

12 000664 Socket, Porcelain 1

13 000469 Wirenut 1

14 000429 Nipple, 1/8 x ½ W Hex Nut, BRS 1

15 000597 Screw, 8-32 x ½”, PHP 2

16 000753 Terminal, Ring 1

17 000419 Nipple, ¼ IPS x ¾, Steel 1

VARIABLE

ITEM PART # DESCRIPTION QTY

18 --- Canopy 1

19 --- Cord, 18-3, SJO/SJTO, 90C 1

20 --- Housing, Switch 1

21 --- Ring, Check 1

22 --- Shade 1

23 --- Lamp, 120V, 250W 1

For all parts not listed, call factory

Contempo Lamps Service Manual

CONTEMPO – STYLE F

COMMON TO ALL STYLE F

ITEM PART # DESCRIPTION QTY

1 000688 Sticker, M. Contempo, UL/NSF 1

2 060434 Bar, Combination, Bracket 1

3 000178 Bushing, Snap, Heyco 1

4 000717 Switch, Toggle 1

5 000430 Nut, 6-32, Hex, Z 2

6 000828 Washer, Lock 1

7 000449 Nut, 1/8 IPS x 9/16, Panel, Z 3

8 000597 Screw, 8-32 x 1 ½”, PHP 2

9 000469 Wirenut 1

10 000671 Socket, Porcelain 1

VARIABLE

ITEM PART # DESCRIPTION QTY

11 --- Canopy 1

12 --- Stem 1

14 --- Ring, Check 1

15 --- Shade 1

16 --- Lamp, 120V, 250W 1

18 000564 Rod All Thread 1

For all parts not listed, call factory

Contempo Lamps Service Manual

CONTEMPO – STYLE R

COMMON TO ALL STYLE R

ITEM PART # DESCRIPTION QTY

1 000688 Sticker, M. Contempo, UL/NSF 1

2 060434 Bar, Combination, Bracket 1

3 000178 Bushing, Snap, Heyco 1

4 000717 Switch, Toggle 1

5 000430 Nut, 6-32, Hex, Z 2

6 000828 Washer, Lock 1

7 000449 Nut, 1/8 IPS x 9/16, Panel, Z 2

8 000429 Nipple, 1/8 x ½ W Hex Nut, BRS 1

9 000469 Wirenut 1

10 000346 Hickey 1

11 000664 Socket, Porcelain 1

12 000416 Nipple, 1/8 IPS x 2” 1

13 000418 Nipple, 1/8 IPS x 5” 1

14 060486 Threaded Rod Assy, 5 ¾” 2

15 000181 Bushing, Hey, 90 Degree 1

16 000179 Bushing, Heyco 1

17 000176 Bushing, Bakelite, 1/8 IPS 2

18 000592 Screw, 8-32 x ¼”, PHP 2

VARIABLE

ITEM PART # DESCRIPTION QTY

19 --- Canopy 1

20 --- Cord, Retract 1

21 --- Housing, Switch 1

22 --- Ring, Check 1

23 --- Shade 1

24 --- Lamp, 120V, 250W 1

25 --- Bracket Assy, Retractable 1

26 --- Stem, 4.5” 1

27 --- Stem, 1.5” 1

For all parts not listed, call factory

Contempo Lamps Service Manual

CONTEMPO – STYLE S

COMMON TO ALL STYLE S

ITEM PART # DESCRIPTION QTY

1 000688 Sticker, M. Contempo, UL/NSF 1

2 060434 Bar, Combination, Bracket 1

3 000178 Bushing, Snap, Heyco 1

4 000717 Switch, Toggle 1

5 000430 Nut, 6-32, Hex, Z 2

6 000828 Washer, Lock 1

7 000449 Nut, 1/8 IPS x 9/16, Panel, Z 3

8 000429 Nipple, 1/8 x ½ W Hex Nut, BRS 1

9 000597 Screw, 8-32 x 1 ½”, PHP 2

10 000469 Wirenut 3

11 000346 Hickey 1

12 000664 Socket, Porcelain 1

VARIABLE

ITEM PART # DESCRIPTION QTY

13 --- Canopy 1

14 --- Stem, 4.5” 1

15 --- Housing, Switch 1

16 --- Ring, Check 1

17 --- Shade 1

18 --- Lamp, 120V, 250W 1

19 000564 Rod All Thread ---

20 --- Wire, 18 GA, Black ---

21 --- Wire, 18 GA, White ---

For all parts not listed, call factory

Contempo Lamps Service Manual 7

CONTEMPO INSTALLATION INSTRUCTIONS

Secure the top portion of the

lamp to the ceiling with the two

8-32 threaded rods provided – as

shown in diagram.

NOTE: A 4” round electrical box

attached to a beam is preferred

to hold the weight and the

adjusting of the lamp up and

down.

ELECTRICAL ATTACHMENTS

BLACK TO BLACK

WHITE TO WHITE

GREEN TO GROUND

Contempo Lamps Service Manual

MERCO SAVORY TRACK LIGHTING INSTRUCTIONS

These instructions are for the proper installation of all Halo Track Lighting fixtures. There are several

different configurations of the Merco Savory track lighting fixtures. All mount to the Halo track in the

same manner as described below.

This fixture is for use with Halo Lighting’s L-Series track system only.

The track plug attaches electrically and mechanically anywhere along the Halo Power-Trac. A two-

position conductor allows use in single circuit track and either circuit of two-circuit track. There are

three terminals on the end of each adapter. To insure proper grounding, locate the side of the

adapter with two terminals and locate side of the track that has two recessed power conductors.

Insert adapter into the track and rotate the proper direction to have the two terminals match up. The

adapter should be inserted into the track and rotated 90°until the locking tab snap into place. To

remove the fixture, press in the locking tab while rotating the adapter 90°.

NOTE: If unit does not operate upon installation, push in tab and rotate fixture 180°to insure adapter

has the proper connection.

CAUTION:

To reduce the risk of burning during re-lamping, remove the entire unit from the track.

Contempo Lamps Service Manual

MINIATURE “TRAC-HEAT” INSTRUCTION SHEET

INSTALLATION OF SINGLE TRAC TO AN OUTLET BOX

CAUTION:

The maximum electrical capacity for POWER-TRAC is 20 Amps per circuit for

permanent installation to an outlet box or 10 Amps if the L950 Cord and Plug

Connector is used to connect the Trac to a wall outlet.

1. Punch out proper knock-out holes in ceiling plate for mounting to outlet box and to live end fitting. (Note that

special, smooth plastic finish piece on metal ceiling plate requires caution in determining location of proper

knock-outs before making holes.) Remove flat head screw(s) from back of live end fitting and use to fasten

plate to fitting.

2. Remove cover from live end fitting. Place Trac with ceiling plate attached over outlet box and mark on ceiling

or wall the position of the Trac mounting holes.

3. Drill mounting holes large for toggles and install Trac with furnished toggle bolts. If Trac is to be mounted on a

solid surface, use screws (not supplied) instead of toggle bolts.

4. Fasten ceiling plate to outlet box with two screws. Pull wires from box through open hole in live end as shown.

5. Cut and strip wires from box and fasten to screw terminals in live end fitting (see detail). Push excess wires

back into outlet box. If ground wire is available, fasten it to the green ground screw.

6. Replace cover on live end and tighten screw.

CAUTION:

Turn off switch at main power source (fuse box) before installing any Trac-heat or

fittings.

Contempo Lamps Service Manual

HEAVY DUTY RETRACTABLE MECHANISM ADJUSTMENT

1. Remove the two screws holding top cover on the retractable cylinder housing.

2. Loosen the two lower hex head-long screws that hold the mounting bracket.

3. Remove the center nut holding the spring mechanism to the mounting bracket.

4. Pull the mechanism out of the cylinder and vary carefully loosen the bolt on the side of the drum a

half turn at a time until the maximum distance required is reached.

5. Reassemble in reverse order.

NOTE: This is only for 060445 Heavy Duty.

Not for 060443 Light Duty.

The 060443 Light Duty Retractable Assembly is not adjustable.

COMMON PARTS TO ALL

PART NUMBER DESCRIPTION QTY

000176 Bushing, Bakelite, 1/8 lps 2

000179 Bushing 1

000181 Bushing, 90 Degree 1

000346 Hickey 1

000416 Nipple, 2” 1

000418 Nipple, 5” 1

000429 Nipple, 1/8 x ½ W/Hex Nut, Brs 1

000435 Nut 8-32 Acorn, NIK 2

000469 Wirenut, Plastic, 105C 2

000592 Screw, 8-32 x ¼ 1

001673 Canopy, Ret. Wht 1

001813 Housing, Switch, 2-hole, Wht 1

001881 Adapter, Showbase White 1

060443 Bracket Assy, Ret, Light Duty 1

060479 Cord, Retract White 1

060486 Threaded Rod Assy, 5 ¾” 2

060506 Stem, 1.5” White 1

060516 Stem, 4.5” White 1

Tabla de contenidos

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario