MERCATOR ikuu SDC8G Manual de usuario
SMART VIDEO DOORBELL
QUICK START GUIDE
SDC8G www.ikuu.com.au
2
This smart video doorbell is designed for use in homes, apartments, oices, garages
and sheds. It’s easy to set up and operate, giving you and your family the security and
peace of mind that you deserve.
You can monitor your video doorbell remotely through the Mercator Ikuü app, which
can be downloaded for free from the Apple App Store and Google Play Store.
1 x Smart Video Doorbell
1 x Indoor Chime
1 x 16GB Micro SD Card*
1 x 5V DC Adaptor (for pairing and indoor chime unit)
1 x 12V DC Adaptor (for doorbell power supply)
1 x USB Cable
1 x Quick Start Guide
1 x Mounting Tools and Screws
*Class 10 required
(Max. 128GB card supported)
Introduction
Contents
3
External Power Ports
Connect supplied cable
from 12V DC adaptor
Reset Button
Use the pin to hold for
5 seconds to reboot
and clear all settings
to factory defaults.
This will allow you
to connect with a
dierent Wi-Fi network
if required.
Speaker
Two way audio
Grub Screw
Location
Grub Screw Location
USB Port
Power with supplied
cable and 5V DC
adaptor
Micro SD Card Slot
Rolling storage
micro SD card
16GB included
(Max.128GB card
supported)
Status Light
RED Solid Light:
indicates the device
has been reset and
is unpaired
RED Blinking Light:
waiting for Wi-Fi
connection
(Pairing Mode)
BLUE Blinking Light:
During pairing or lost
Wi-Fi connection
BLUE Solid Light:
Video Doorbell is
running correctly
Ring Button
Press to activate
doorbell
Camera Lens
1080p HD, with
130° angle of view
Microphone
Light Sensor/
Infrared LEDs
Detects low light
and turns on the
infrared lights which
allow the camera
to capture both day
and night images.
Identification
4
1. Download the Mercator Ikuü app.
2. Tap ‘create new account’ or ‘log in to account’.
3. Follow the in-app prompts and tap ‘OK’.
Log in to the
Mercator Ikuü
app.
Note: Ensure your
Video Doorbell is
in pairing mode.
The LED should
be flashing red.
If it isn’t, use the
reset pin to press
and hold the reset
button on the
back of the unit
for 5 seconds and
wait for the Video
Doorbell to restart.
1
Tap the icon
and select
‘Add Device’.
2
Connect Your Video Doorbell to the App
Set Up the App
5
Connect Your Video Doorbell to the App (cont.)
Select
‘Doorbell’ from
the sidebar,
and then tap
the Video
Doorbell icon.
3
When the
prompt
appears, tap
‘next step’.
4
Enter your
Wi-Fi name and
password, then
tap ‘Confirm’.
5
When the
prompt
appears, tap
‘Continue’.
6
6
Place the
camera eye
over the QR
code to scan
(holding the
camera 15cm
away from your
mobile screen).
When you hear
the prompt,
tap ‘I Heard a
Prompt’.
7
The app
will begin
connecting
to your video
doorbell.
When it
reaches 100%,
you will be
taken to the
product’s
settings page.
8
Update the
name of
the device
(optional), then
tap ‘Done’.
9
The Video
Doorbell feed
will open, and
you will be
prompted to
allow access to
your device’s
microphone.
Tap ‘OK’ to
continue. Your
Video Doorbell
is now
connected and
ready for use.
10
Connect Your Video Doorbell to the App (cont.)
7
Doorbell Functions
Take a photo of the live video feed, which will be saved to the
photo album.
Speak through the doorbell speaker via your phone
microphone.
Take a video of the live video feed, which will be saved to the photo
album. 24/7 recording and event recording available.
Review camera footage from the SD card (if installed).
Adjust motion detection settings.
View previously saved photos and video recordings. You can download
these to your local mobile device.
Adjust the date when reviewing playback.
8
Pairing Your Indoor Chime Unit
1. In a location near your door and with good Wi-Fi coverage, power on your indoor
chime unit with either a standard USB-A port or the provided DC power adaptor.
The status light will blink red to indicate that the chime is ready for pairing.
2. To put the chime in pairing mode, push the reset button once (located at the
rear of the chime unit). The status light will blink continuously. Ensure that it is
blinking for at least 5 seconds before completing step 3.
3. In the app, navigate to settings > bell settings > bind. The status light will
stop blinking and remain solid blue to indicate that the chime is paired. Aer
successfully pairing the indoor chime unit, you can adjust the ringtone
and volume.
Note: If your chime unit is showing as paired, but makes no sound when the doorbell
is pressed, try unbinding the chime unit and binding it again. Ensure that the status
light indicator is blinking slowly and continuously before tapping ‘bind’ in the app.
If there is still no sound when the doorbell is pressed, try moving it closer to the video
doorbell unit.
9
Installation Instructions
Before choosing your location, check the Wi-Fi strength/coverage in that area.
WARNING: Do not connect both power supplies together at anytime.
IMPORTANT: Mount the doorbell under eave and avoid placing it in direct sunlight
and extreme weather. Do not mount the doorbell unit on metal or near metal door
frames, security door, or proximity any metal door furniture as this might aect the
functionality of the doorbell.
Please note: The below image shows the doorbell angle view. Install it in a suitable
location with Wi-Fi coverage (Fig.01).
Wi-Fi Coverage
FIG. 01
10
Note:
• This doorbell requires a network device (e.g. wireless/non-wireless router, network switch etc.)
that is connected to the internet for setup and use. This network device is not supplied with
this kit.
• This doorbell might experience network, motion command and live transmission delay issues.
This is normal, due to the connected network, 3G/4G mobile network, server overflow or internet
upstream speed, download speed and video resolution. To reduce delay, it is recommended to
reduce the video quality, or contact your mobile/network service provider.
There are two mounting methods to
choose from. Note: The angled wall
mount requires the flat wall mount for
installation.
1. Position 12V DC power adaptor to
an outlet as close to your mounting
location as possible. Do not plug in
your adaptor.
2. Route adaptor wire with extension
cord to doorbell location. Do not
connect to the doorbell.
3. Mark screw position using
bracket. Pass 12V DC adaptor with
extension cord through middle of
the brackets (Fig.02)
4. a) Angled Wall Mount
Using both mounts, secure to
mounting surface with supplied
screws and wall plugs (Fig.02)
b) Flat Wall Mount
Install as described above without
angled wall mount.
5. Connect 12V DC adaptor with
extension cord to the two terminals
at the back of the doorbell Fig.03.
6. Install the doorbell to the bracket
using supplied grub screw Fig.04.
7. Plug in 12V DC adaptor and your
doorbell is ready for use.
Flat Wall
Mount
Terminals
Rear of
Doorbell
Angle Wall
Mount
Wall
Plugs
Mounting
Screws
DC
Adaptor
Wire
Adaptor
Wires
Grub
Screw
FIG. 02
FIG. 03
FIG. 04
Tabla de contenidos
