MEMC MRMC-2091-00 Manual de usuario
ii
Universal E-stop System Quick Start Guide
QSG Product Code: MRMC-2091-00
Date Modified: 11 September 2020
Product Covered: MRMC-2075-00
© 2019 Mark Roberts Motion Control Ltd. All rights reserved.
No part of this publication may be reproduced, transmitted, or translated
by any means — graphical, electronic, or mechanical — including
photocopying, recording, taping, or storage in an information retrieval
system, without the express written permission of Mark Roberts Motion
Control.
Although every care has been taken to ensure that the information in this
document is accurate and up to date, Mark Roberts Motion Control
continuously strives to improve their products and may make changes to
the hardware, firmware, and software described in this document. Mark
Roberts Motion Control therefore cannot be held responsible for any
error or omission in this document.
All product names mentioned herein are the trademarks or registered
trademarks of their respective owners.
Contact information
Mark Roberts Motion Control Ltd.
Unit 3, South East Studios
Blindley Heath
Surrey
RH7 6JP
United Kingdom
Telephone: +44 (0) 1342 838000
E-mail: info@mrmoco.com (sales and general enquiries)
Web: www.mrmoco.com
www.mrmocorentals.com
iii
Universal E-stop System Quick Start GuideUniversal E-stop SystemQuick Start Guide
Contents
Chapter 1 Quick start ..................................................................... 1
Important safety instructions ............................................... 1
Power and connections................................................1
General care...................................................................1
Location................................................................................... 1
Intellectual property ..............................................................1
Overview ................................................................................. 2
Connecting the cables ...........................................................3
Universal E-stop System with a Single Robot ...........3
Safety Relay PLC LEDs..........................................................4
Universal E-stop System with Multiple Robots ........5
E-stop Button Expansion............................................. 6
Universal E-stop Bypass Operation.....................................8
RT-14 Bypass Operation ....................................................... 9
Universal E-stop System Quick Start Guide
iv
1
Universal E-stop System Quick Start GuideUniversal E-stop SystemQuick Start Guide
Chapter 1 Quick start
Important safety instructions
To ensure the best from the product, please read this manual carefully.
Keep it in the safe place for future reference.
To reduce the risk of electric shock, do not remove the cover from the
unit. No user serviceable parts inside. Refer servicing to qualified
personnel.
Power and connections
This unit must be connected to a 24V DC PSU supplied.
Do not plug in or attempt to operate an obviously damaged
unit.
General care
Do not force switches or external connections.
Do not attempt to clean the unit with chemical solvents or
aerosol cleaners, as this may damage the unit. Use a clean dry
cloth.
Do not use around flammable gas. All electrical equipment can
generate sparks that can ignite flammable gas.
Keep the equipment dry. The system has not been made
weatherproof. Do not use with wet hands.
Keep away from pets and children.
Location
Installation of this unit should be away from sources of excessive heat,
vibration, and dust.
Intellectual property
This product includes confidential and/or trade secret property.
Therefore, you may not copy, modify, adapt, translate, distribute, reverse
engineer, or decompile contents thereof.
Universal E-stop System Quick Start Guide
2
Overview
Thank you for using the Universal E-Stop System from Mark Roberts
Motion Control (MRMC). The Universal E-Stop System is a safety relay
PLC between RT-14 and MRMC Motion Control and Broadcast rigs and
is fully integrated with the Flair Motion Control Software.
The Universal E-Stop System has the following main features:
Can be used as a safety PLC for a single robot. Multiple robots
using the Universal E-stop can be easily "daisy-chained" to
create a global E-stop system
An arbitrary number of additional E-stop buttons can be
attached and deployed in the customer setup
Universal E-stop System Quick Start Guide
3
Connecting the cables
Universal E-stop System with a Single Robot
RT-14
E-STOP
Jumper
[19788]
Jumper
[15843]
Jumper
[14823] To Rob ot
Controller
or umbilical
ROBOT
POWER IN
To
Additional
hardware
24V PSU
Safety PLC
E-stop Relay
Desk
top
E-stop
box
[19782]
Hand held
box or bypass
jumper
XLR cable
[18826]
Cable
[18833]
The two E-stop Status Non-safe connectors provide Auxiliary relay
output and can be connected to additional non-MRMC or custom device.
Any hardware that is plugged with these two connectors will be stopped
when the E-stop button connected with the Universal E-stop system is
pressed but the reverse is not true. In other words, the Universal E-stop
System will not accept any feedback from such devices.
Universal E-stop System Quick Start Guide
4
Safety Relay PLC LEDs
LED/Key Description
Blue On indicates that the Safety Relay has power.
Green On indicates that the E-stop is enabled and the
robot can be engaged. Off indicates that the E-stop
is pressed and robot is disengaged and cannot be
re-engaged.
Red On indicates that the RT-14 Bypass key is in
horizontal position and RT-14 is bypassed. In this
condition both the software E-Stop (from Flair) and
the HHB E-stop have no effect. For safety reasons,
always ensure that this LED is off unless RT-14 is
bypassed temporarily on purpose.
Universal E-stop System Quick Start Guide
5
Universal E-stop System with Multiple Robots
Universal E-stop System with robot two
RT-14
E-STOP
Jumper
[14823]
Desk
top
E-stop
box
[19782]
To Robot
Controller or
umbilical
ROBOT
POWER IN
24V PSU
Safety PLC
E-stop Relay
RT-14
E-STOP
To Robot
Controller or
umbilical
ROBOT
POWER IN
24V PSU
Safety PLC
E-stop Relay
Jumper
[19788]
Universal E-stop System with robot one
Hand held
box or bypass
jumper
Hand held
box or bypass
jumper
XLR cable
[18826]
Cable
[18833]
XLR cable
[18826]
Cable
[18833]
[19862]
Jumper
[15843]
Jumper
[15843]
Universal E-stop System Quick Start Guide
6
Any number of Universal E-stop Systems can be added to the chain as
long as the one at the beginning of the chain has the Desk top E-stop box
plugged into E-Stop In and the one at the end of the chain has a jumper
plugged into E-stop Thru connector.
E-stop Button Expansion
Only one main E-stop box [19782] is used per safety relay box, which is
plugged to the E-stop In connector.
When using multiple desk top E-stop boxes, E-stop Extension Cable
[18466] is used to ‘chain’ the E-stop boxes.
RT-14
Jumper
[19788]
To Robot
Controller
or umbilical
ROBOT
POWER IN
Additional
hardware
24V PSU
Safety PLC
E-stop Relay
Jumper
[14823]
Any number of desk top e-stop
boxes [18519] can be added to the
chain as long as the one at the end
of the chain has the jumper
[14823] plugged into it.
Desk-top E-stop
box [19782]
(Must be first in
the chain)
XLR cable
[18826]
Cable
[18833]
Hand held
box or bypass
jumper
Jumper
[15843]
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
