MELICONI GumBody Universal 5 web Manual de usuario

Keep this booklet for future reference.

Thank you for choosing a Meliconi remote control.

The Universal 5 web remote control is ideal for replacing up to 5 remote controls for TV - SAT (satellite decoder)

- TER (Digital Terrestrial decoder) - DVD (Dvd player and Blu Ray) – PVR (Personal Video Recorder, Media

Center and VCR). Moreover, thanks to its AUDIO UPDATE function, the device can also be connected to a PC

via the cable supplied in order to download the information required to conﬁgure it. The Universal 5 web remote

control also has a LEARN function so it can learn any original remote control signals not yet inserted in the

databank, as well as allowing secondary functions to be acquired and saved on the F1 - F2 - F3 - F4 function

keys or on any other button on the keypad. The remote control has a non-volatile memory, meaning that it does

not lose its settings even if there are no batteries in it. Its ergonomic shape and soft rubber body make it easy to

grip and protect the remote control if it is knocked or dropped.

IMPORTANT: The remote control must not be exposed to excessive heat sources.

USE OF THE BUTTONS AND FUNCTIONS

The functions of the buttons described below are available only if they are on your original device.

Volume control +/–

TELETEXT buttons

ON/OFF switches the device OFF and

in some cases ON

Numeric keypad

Conﬁrm selection

MUTE turns sound OFF and ON

For selecting an external

input source

For selecting the next programme P+

or the previous programme P–

For moving around within the MENU

Buttons for selecting the device to be

controlled.

Fastext functions or for selecting sub-

menus using colours

DVD/PVR RECORD PAUSE

STOP PLAY buttons

DVD and PVR forward/back functions

Speciﬁc buttons for decoder

Displays the list of programmes

Selects analogue/digital

Selects digital TV and radio

Button for activating the LEARN function.

The button lights up when commands are

being captured or transmitted

User customised buttons that additional

commands can be saved to and accessed

directly from

INSERTING THE BATTERIES

Before using the remote control, insert the batteries and programme it.

The remote control requires 2 new 1.5V alkaline AAA/LR03 batteries.

Insert them as illustrated.

Try pressing a number button and check that the red light remains lit

continuously until you release the button. If the light ﬂashes, the batteries

inserted are not charged and are about to go ﬂat, therefore you must

substitute them.

Do not leave ﬂat batteries inserted, as liquid may leak and damage the remote control

The Universal 5 web remote control is a universal remote, so its memory contains data relating to numerous

devices of various brands available on the market.

Each original device has a speciﬁc code which must be used to set up the remote control.

Therefore, to use your Universal 5 web you must enter the speciﬁc code for each device you wish to control.

So use one of the following methods to identify the correct code and set it in your remote control:

A) - INTERNET (recommended)

B) - CELL PHONE (SMS)

C) - MANUAL SEARCH

SETTING CODES

If you have an Internet connection available, follow the on-line guide on the www.meliconi.com/guide website

to identify the speciﬁc codes for the devices you wish to command. Then set the codes manually in your

MELICONI remote control as described in the ENTERING THE CODE DIRECTLY procedure.

SETTING CODES USING INTERNET

Today, Meliconi gives customers who don’t have internet the chance to receive the codes for programming their

remote control directly on their cell phone.

Simply send an SMS to this number 0039 345 7518893 as follows: 5A, Type, Brand, Model

-Type = indicatethedevicetobecontrolledusingoneofthefollowingabbreviations:TV -SAT -DVD -VCR-TER

(Digital Terrestrial decoder) -AUX (other audio video device).

-Brand, Model = to indicate the brand and the model of the device to be controlled.

Example: 5A, TV, PHILIPS, 32PFL3614 (if you don’t know the model, don’t write anything after the brand).

Once you have received the SMS with the list of codes, set the ﬁrst code in the remote control as described in

the ENTERING THE CODE DIRECTLY section.

Stand in front of the device with the MELICONI remote control. Turn the device on and then press the OFF button

on the remote (or the PLAY button if the device is a VCR/DVD).

If the device does NOT switch off (or if the VCR/DVD does not start playing), try setting the consecutive code

in the SMS list in the remote control.

When the device reacts check whether the other buttons are operating correctly too.

If they do, the remote control is ready to use.

If they don’t, you are probably using an incorrect code destined for a very similar device; at this point

ignore the SMS list and consult the SETTING CODES USING A MANUAL CODE section to ﬁnd a more suitable

code.

SETTING CODES USING A CELL PHONE

NOTE: If you don’t receive an SMS on your cell phone or if the message says ERROR / NO CODE, it

means the system has not been able to process the data you have sent; Do not try sending another

SMS use the MANUAL SEARCH instead.

SETTING CODES USING A MANUAL SEARCH

(only to be performed if the speciﬁc code could not be found)

CHECK

Check that the other buttons correspond to the functions of the original remote control; if not, it is likely

that the code found is incorrect, but is used for a very similar device. In that case, repeat the procedure

from point 2.

If the manual search for the code is successful, obtain the code in use by following the DISPLAY CODE IN

USE procedure and make a note of it inside the battery cover.

NOTE: During the search the indicator stops ﬂashing and the remote control exits the programming mode

in the following cases:

• if for 12 seconds the button indicated is not pressed or if another button is pressed

• if the list of codes to ﬁnd is terminated. If this happens, go to the www.meliconi.com website

1. Switch on the device to be programmed:

- if it is a TV, SAT or TER select a programme

- if it is a DVD insert a DVD.

- if it is a VCR insert a cassette.

2. Press and hold down for 6 seconds the device selection

button corresponding to the device you wish to enter

the code for. Note: Use the PVR button if the device is a

VCR.

3. Release the button. The indicator light will ﬂash. Point

the remote control at the device and press the ON/OFF

key (or PLAY if it is a VCR/DVD). If the device does NOT

switch off (or if the VCR/DVD does not start playing)

press the same button again slowly (it may be necssary

to press the button several times).

4. When the device responds correctly, press OK. Three

long ﬂashes indicate that the operation has been carried

out correctly.

6 SEC.

or or or or

ENTERING THE CODE DIRECTLY

(only to be performed if you know the speciﬁc code to be set)

1. Press and hold down for 6 seconds the device selection

button corresponding to the device you wish to enter

the code for. Note: Use the PVR button if the device is a

VCR.

2. Release the button. The indicator light ﬂashes.

Immediately enter the speciﬁc code previously found.

(e.g.. 1306).

3. Three long ﬂashes indicate a correct setting.

If they do not appear, repeat the procedure. If this still does not work it means the code indicated

is not in the remote control, so it must be loaded using the INTERNET as described in the following

section.

6 SEC.

or or or or

UPDATING VIA AUDIO CABLE

DISPLAY CODE IN USE

To use this function, the remote control you wish to copy the function from must be working

learn the missing functions from an original remote control and save them on the F1 - F2 - F3 -

F4 buttons or on a normal remote control, thereby replacing the command that was on the button

previously.

learn all the functions from a new remote control not included in the universal remote control databank

because it was released on the market afterwards.

Using this function you can:

LEARN FUNCTION

Connect the remote control using the audio cable in the kit

supplied to a PC with an internet connection. Connect the

cable as follows:

1. Open the remote control battery compartment.

2. Connect the ﬂat end of the cable (A) to the connector at

the three points J1 under the battery housing (B), taking

care not to press too hard (C).

3. Connect the jack at the other end of the cable (D) to the

PC audio output (or headphones output).

4. Follow the instructions in the on-line guide at www.

meliconi.com/guide.

If you set up the remote control using the MANUAL

SEARCH procedure, obtain and make a note of the code

in use as follows:

1. Press and hold down for 6 seconds the device selection

button corresponding to the device you wish to enter

the code for. Note: Use the PVR button if the device is a

VCR.

2. Release the button. The indicator light will ﬂash. Press

the TV / radio button for an instant.

3. After a pause of several seconds, the indicator light

produces four sets of ﬂashes, spaced out, corresponding

to the code to be obtained. Count the number of ﬂashes.

Each set of ﬂashes corresponds to one ﬁgure in the code.

Ten ﬂashes correspond to the ﬁgure 0.

4. Make a note of the code obtained on the label on the

inside of the battery cover. You may need it in future. Code obtained = 1306

ABC

6 SEC.

or or or or

Learning missing functions from an original remote control and saving

them on any button on the Universal 5 web

To acquire signals you must ﬁrst make sure that the remote controls are the correct distance apart:

At this point the maximum data exchange distance between the two remote controls will have been

reached. To acquire signals the remote controls must now be positioned at half this distance and then not

moved any further until the process has terminated.

Important: when you release the button, if the LEARN button light comes on again, press the same button

on the original remote control again until the light goes out once more.

Having programmed the Universal 5 web, every time you press a button linked to a LEARN command,

both the light corresponding to the device being used and the LEARN button light will come on.

1. Position the original remote control in front of the

universal remote control so that the areas which emit the

infrared signals are opposite each other at a distance of

approximately 5 cm.

2. Press the LEARN button for an instant and then, within

ﬁve seconds, press and hold down any button on the

original remote control. The green light under the LEARN

button should then start ﬂashing. If it doesn’t move the

remote controls closer together.

3. Gradually increase the distance between the two remote

controls, making sure that they stay aligned until the

point at which the green light under the LEARN button

stops ﬂashing.

5 cm

max. dist.

4. Press the selection button for the required device for an

instant.

5. Press the LEARN button for an instant together with

one of the F1 - F2 - F3 - F4 buttons or any other normal

button you wish to save the new function on.

6. The green light on the LEARN button will light up in

steady mode to indicate that it is waiting to receive a

signal from the original remote control.

7. On the original remote control, press the button

corresponding to the signal you wish to capture and hold

it down until the green light on the LEARN button goes

out.

or or or

8. If the procedure has been completed successfully the

red light corresponding to the selected device gives

three long ﬂashes. Only at this point will the remote

control be ready to capture other signals to be saved on

other buttons.

or or or or

DELETING ALL THE LEARN COMMANDS

All the signals captured with the LEARN function can be deleted by setting the 9000 code on any of

the device selection buttons. This will restore the original commands on the buttons.

HOW TO CONTROL MELICONI AUDIO VIDEO ACCESSORIES

The Universal 5 web is already programmed to control the Meliconi Ghost Motor 100 motorised wall brackets

and the Meliconi Light Kit lighting strips. Simply set the code 4000 on one of the device selection buttons. To

ﬁnd out which buttons are linked to the functions available, consult the online product guide in the www.meliconi.

com/guide website.

MEMO FUNCTION

The MEMO function enables you to record a sequence of commands and to recall them by pressing a single

button. For example: turn on the TV, turn on the DVD, play a video, etc. To access this function, consult the online

guide in the www.meliconi.com/guide website.

AUDIO CONTROL

When you select a device that does not have its own audio controls, if you press the V+, V- and Mute buttons the

audio on the device memorised as TV will be commanded.

This setting can be changed by linking the audio commands of a different device to the V+, V- and Mute buttons.

To do this follow the simple procedure outlined in the online guide in the www.meliconi.com/guide website.

Learning all the functions from a new remote control not yet included

in the Universal 5 web databank

With the Universal 5 web you can create up to 5 completely empty keypads so that in LEARN mode a

total of up to 64 new commands can be obtained.

Having constructed one of these keypads with the LEARN commands you can deactivate it by setting

another code on the device selection button and then recalling it exactly as it was by resetting the 8x00

code on the same or another device selection button.

1. Follow the code entry procedure using one of the

following codes: 8000, 8100, 8200, 8300, 8400.

2. To acquire and save signals from one or more original

remote controls follow procedure.

HOW TO ACTIVATE ADDITIONAL COMMANDS

For lesser used functions, ﬁnd the additional commands by consulting the www.meliconi.com/guide website.

Using the online guide, as well as ﬁnding the code required to programme your remote control, you can also

ﬁnd descriptions of which Universal 5 web remote control buttons correspond to the additional commands you

require. You can save additional commands on the F1 - F2 - F3 - F4 function buttons.

TROUBLESHOOTING

PROBLEM

The device does not respond and the indicator light

does not come on when a button is pressed.

The device does not respond but the indicator light

comes on.

When you press a button the indicator light ﬂashes

and the device does not respond to commands.

The remote control does not execute all commands

correctly.

SOLUTION

Check that the batteries are charged and inserted

correctly and if necessary replace them with 2 new

1,5 V AAA/LR03 alkaline type batteries.

Make sure that the remote control is pointing at the

device and that there are no obstacles in the way.

If necessary, enter the remote control code again by

repeating the programming procedure.

Substitute the batteries, which are about to go ﬂat.

You may be using an incorrect code.

Enter the remote control settings again by repeating

the programming procedure.

INFO - LINE

•carefully read this Instructions Booklet which will allow you to solve most problems

•consult the www.meliconi.com website where you will ﬁnd all the answers you need quickly and easily.

2 year WARRANTY

The warranty is voided if the product is tampered

with or used improperly.

Remote control model Universal 5 web

Purchase date

Retailer stamp

The symbol showing a wheelie bin with a cross through it which appears on the device indicates that at the end of its useful life the

product must be collected separately from other waste. Therefore, at the end of the device’s life, you must take it to appropriate centres

for the differentiated collection of electrical and electronic waste, or return it to the retailer when purchasing a new device of equivalent

type, on a one-for-one basis. Suitable differentiated collection to allow subsequent recycling of the decommissioned device, with

environmentally-compatible treatment and disposal, help to prevent any negative effects on the environment and health and to promote

the recycling of the materials of which the device is made. Improper disposal of the product by the user will be subject to the sanctions

in Legislative Decree No. 22/1997 (article 50 and subsequent articles of Legislative Decree No. 22/1997).

If you have any questions about the new Universal 5 web remote control:

Tabla de contenidos

Otros manuales de Mando a distancia de MELICONI

MELICONI

MELICONI pratico 6 Manual de instalación y operación

MELICONI

MELICONI personal 4 Manual de usuario

MELICONI

MELICONI Personal 6+ Manual de usuario

MELICONI

MELICONI FACILE 1 RC Manual de usuario

MELICONI

MELICONI PRATICO 2 Light Manual de usuario

MELICONI

MELICONI Fully 8 RC Manual de usuario

MELICONI

MELICONI CONTROL 3-300 PLUS - WINDOWS Manual de usuario

MELICONI

MELICONI EASY 200 Manual de usuario

MELICONI

MELICONI Personal 5+ Manual de usuario

MELICONI

MELICONI MYCRO Manual de usuario

MELICONI

MELICONI Control TV.1 Manual de usuario

MELICONI

MELICONI Pratico 2 Manual de usuario

MELICONI

MELICONI CONTROL 2 Simple Manual de usuario

MELICONI

MELICONI Colibri 2 Manual de usuario

MELICONI

MELICONI Speedy 210 combo Guía de instalación

MELICONI

MELICONI EASY 300 Manual de usuario

MELICONI

MELICONI Control 5 500 PLUS Manual de usuario

MELICONI

MELICONI Algo 2.1 Manual de usuario

MELICONI

MELICONI TLC05 Manual de usuario

MELICONI

MELICONI TLC04 Manual de usuario

MELICONI

MELICONI Personal 4+ Manual de usuario

MELICONI

MELICONI GUMBODY UNIVERSAL 3-300 Manual de usuario

MELICONI

MELICONI GumBody DIGITAL 2 SMART Manual de usuario

MELICONI

MELICONI TLC05 Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación