MEFE 139 300 Manual de usuario
MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 1
+617 3283 4536
Free AU 1800 669 006
Operaon Manual
Power Belt Knife Sharpener
CAT 139 300
Revision 3
MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 2
+617 3283 4536
Free AU 1800 669 006
Contents
1. About the Power Belt Knife Sharpener......................................................................... 3
1.1 Before Use................................................................................................................ 3
1.2 Liability and Warranty.............................................................................................. 3
2. Abrasive Belt Installaon............................................................................................... 4
2.1 Adjusng the Posion of the Belt Holder ................................................................ 4
3. Switch Operaon............................................................................................................ 5
4. Blade Grinding................................................................................................................ 6
5. Specicaons.................................................................................................................. 7
6. Parts List ......................................................................................................................... 7
MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 3
+617 3283 4536
Free AU 1800 669 006
1. About the Power Belt Knife Sharpener
The Power Belt Knife Sharpener is designed to sharpen every knife you own, quickly and easily. The Power Belt Knife Sharpener
uses a fully adjustable precision sharpening guide (15° to 30°), heavy-duty variable speed motor, and premium ¾ x 12” exible
abrasive belts to sharpen pocket knives, hunng knives, kitchen knives, shing knives and virtually any other shape or type of
blade – even scissors, shears and yard tools. It’s fast, easy, and delivers consistent results.
1.2 Before Use
This manual has been established for secure handling of your Power Belt Knife Sharpener. Before starng to operate the Power
Belt Knife Sharpener, please read this manual carefully. The safety instrucons contained within must be observed at all mes.
Always keep a copy of this manual within close reach of the item.
A new user is advised to rstly choose a wider angle (more than 25 degrees) to beer know the strength of grinding (no need
to press the abrasive belt, just touch it). It should also be noted that the direcon of grinding on both sides of the belt is dier-
ent and the blade should be ground close to the outer edge of the V-groove.
You need to make sure that the blade stays the same height throughout sharpening, especially along the side that rotates
downwards.
Do not use the sharpener for more than 20 minutes each me as it is mainly used for restoraon of sharp cung tools. Make
sure to clean aer each use.
1.3 Liability and Warranty
All specicaons and instrucons for operaon and maintenance of the Power Belt Knife Sharpener are made to the best of
our knowledge taking into account our experse and experiences so far. The manufacturer will accept no liability for any dam-
ages caused by not following the instrucons of this manual.
MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 4
+617 3283 4536
Free AU 1800 669 006
2. Abrasive Belt Installaon
Firstly put the abrasive belt over the tension wheel and the impeller, then push the tension rack towards the driven wheel and
slip the belt over the driven wheel. Then ne tune the posion of the belt over the three wheels.
2.1 Adjusng the Posion of the Belt Holder
Place the Sharpener on a solid surface then press and hold the spring posioning pin and turn the Belt Holder to the angle that
is desired. Release the posioning pin and slot the Belt Holder into posion.
Driven Wheel
Tension Wheel
Impeller
Tension Rack
Spring Posioning Pin
MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 5
+617 3283 4536
Free AU 1800 669 006
3. Switch Operaon
The switch has mulple funcons, which consists of three parts: the buon, the ne tuning knob, and the self locking buon.
The switch has two operang modes:
1) Variable speed mode: turn the ne tunning knob towards the “+” all the way to the end. Press the buon gently to start
o slow then push the buon all the way in to go to fast, then press the self locking buon. To release the self locking
buon, press the buon again.
2) Fine tuning speed mode: speed up and speed reducon can be done by turning the ne tuning knob towards the “+”
and the “-”. The self locking buon must be pressed in.
Buon
Self locking Buon
Knob
Fine Tuning Knob
MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 6
+617 3283 4536
Free AU 1800 669 006
4. Blade Grinding
Adjust the angle of the knob from about 15 degrees to 30 degrees and then install proper abrasive belts. Usually a lower grit
belt should be used rst to grind out the edges and then a higher grit should be used for grinding and polishing to ensure the
sharpness of the blade.
Aer the belt is installed, put the knife inside either V-groove between the le and right guiding racks, and then push and pull
the knife, sharpen from the base of the blade to the p of the blade and keep close to the outer edge of the racks (use only the
knife's own strength without adding too much force outwards or downwards).
To use or put away the small rack, gently pull and twist it sideways.
Generally speaking, a low to medium speed may be enough for the grinding of outdoor or daily knives. Repeatedly push and
pull the knife, and be careful to keep the p of the blade away from the belt as to not round it o. Turn o the rotang abra-
sive belt as soon as you have nished sharpening.
Driven Wheel Rack
Small Rack
Panel
Impeller
Posioning Pin
Knob
Guiding Rack
Self Locking Buon
Buon
Fine Tuning Knob
Tension Wheel
Tension Rack
Adjusng Buon
MEFE—Mitchell Engineering Food Equipment Pty Ltd
23 Storie Street Clontarf QLD 4019 Australia
www.mefe.com.au | [email protected]
Page 7
+617 3283 4536
Free AU 1800 669 006
5. Specicaons
6. Spare Parts List
Weight 1.36 kg
Dimensions 260 x 152 x 135mm
Colour Black
Style Regular Knife and Tool Sharpener
Number of Handles 1
Motor 110VAC / 1.5 AMP
200V / 1.8 AMP
Power Switch Variable Speed: On / O / Momentary
Duty Cycle 1 hour connuous
Abrasives Included A180, A320, A600, A1000
Abrasive Size 3/4” x 12”
Sharpening Guides Adjustable, 150—300
Aachments Tool grinding aachment and blade grinding aachment
Part Number Descripon
139 300A180 180 Grit Abrasive Belt
139 300A320 320 Grit Abrasive Belt
139 300A600 600 Grit Abrasive Belt
139 300A1000 1000 Grit Abrasive Belt
Tabla de contenidos
Otros manuales de Accesorios de MEFE
