Meanwell LCM-25 Manual de usuario

Wiring

Environmental limitations

Cautions

Settings and connections

1. Output Current Level Settings

Features

‧180~277VAC input only

‧Built-in active PFC

‧Output current level selectable by DIP switch

‧Built-in 0~10Vdc and PWM signal dimming function

Power supply synchronization function up to 10 units‧

‧ⅡClass power unit, ungrounded

‧Full plastic case enclosed

‧No load power consumption <0.5W

‧Protections: Short circuit / Over temperature

‧3 year warranty

Suitable for intelligent LED lighting‧

‧Housing with cable clamp for remote installation

‧Use wires with an adequate cross-section (see 4)

‧Use suitable mounting tools to do the wiring and mounting (see 4)

‧Use a (miniature MCB circuit breaker) with an adequate current rating to protect the lighting system (see 6)

‧℃Maximum ambient temperature must not exceed 60

‧Always allow adequate ventilation clearances, 50mm, around the unit in use to prevent it from overheating

‧Only install the unit in interior environments

‧This unit must be installed by a qualified electrician

‧It's not suitable to connect DC/DC constant current drivers as the output loads

The LCM can provide various output currents by setting the DIP switch. The settings of the DIP switch are shown in the tables below.

LCM-25

Note : 1.Factory default setting is 700mA.

2.Output voltage and output wattage must not exceed the rated values.

Voltage

range 1 2 3 4 5 6

Selectable

Current

6-54V --- --- --- --- -- - - - -

--- --- --- --- -- -

--- ---

---

ON ON

ON ON ON ON

ON ON ON ON ON

ON ON ON ON ON ON

350mA

6-50V 500mA

6-42V 600mA

6-36V 700mA*

6-28V 900mA

6-24V 1050mA

LCM-25 installation manual

Terminal blocks assignment for LCM

2. Connection of LED Lamps

Press down the "push button" by a slotted screw driver to insert or remove the cable.

Vo-

Vo+

AC/N

AC/L

NEUTRAL (Blue or white)

LIVE (Brown or black)

http://www.meanwell.com



  



SYN.

AC/N

AC/L

105mm

68mm

23mm

+Vo

-Vo

DIM-

DIM+

+ +

- -

3. Connection of Dimming Functions

a. 0~10Vdc or 10V PWM

b. Synchronization operation

http://www.meanwell.com

DIM-

DIM+ 0~10Vdc or 10V PWM

4. Recommended Screwdriver, Wire and Torque Setting

5. Suggested Maximum Number of the LCM Units that can be Connected to a MCB ( circuit breaker) at 230Vac miniature

Note: These calculated values are based on MCB S201 series manufactured by ABB.

Type

Model B10 B16 C10 C16

LCM-25 20 32 34 54

Solid wire

Stranded wire

American wire gauge

Wire stripping length

Screwdriver

Recommended tightening torque

Suggested push-down strength

-----

6mm Philips

4kgf-cm (3.47 lb-in)

Clamp connector Push terminal

(ACL/N)

Ј0.8 -Ј1.8mm

0.5 - 2.5mm

14 - 20AWG

10mm (0.39")

3mm Slotted

-----

3 - 4 kp (6.61-8.81 lbF)

Ј0.8 -Ј1.382mm

0.5 - 1.5mm

16 - 20AWG

7mm (0.27")

3mm Slotted

-----

1.5 - 2.4 kp (3.31-5.29 lbF)

Push terminal

(Vo , DIM )± ±

+Vo -Vo DIM- DIM+

LCM-25

(Master)

LCM-25

(Slave 4)

LCM-25

(Slave 1)

LCM-25

(Slave 5)

LCM-25

(Slave 9)

SYN. SYN.SYN. SYN. SYN.

CN101

CN100

5m 5m

-- ---

.....

.. .

‧Synchronization up to 10 drivers (1 master + 9 slaves)

Dimming operating range : 10%~100%‧

‧Sync cable length : < 5m

‧Sync cable type : Flat cable

‧Sync cable cross section area : 22 – 24 AWG (0.2~0.3mm )

‧Cn100, CN101 : used to synchronously control the LCM

units in parallel.

NOTE: 1. Please make sure all units are set to 100% dimming setting (factory default) before synchronizing.

2. Min. Dimming operating range depends on dimmer setting.

Otros manuales de Fuente de alimentación de Meanwell

Meanwell

Meanwell RCP-2000 Manual de usuario

Meanwell

Meanwell LCM-40(DA) Manual de usuario

Meanwell

Meanwell HEP-1000 Manual de usuario

Meanwell

Meanwell LPHC-18 Manual de usuario

Meanwell

Meanwell VFD Series Manual de usuario

Meanwell

Meanwell RST-7K5-HV Series Manual de usuario

Meanwell

Meanwell RSP-2400-12 Manual de usuario

Meanwell

Meanwell SDR Series Manual de usuario

Meanwell

Meanwell TDR-960 Series Manual de usuario

Meanwell

Meanwell MDR Series Manual de usuario

Meanwell

Meanwell LCM-25KM Manual de usuario

Meanwell

Meanwell DDR-15G-3.3 Manual de usuario

Meanwell

Meanwell NDR-75 Series Manual de usuario

Meanwell

Meanwell IRC1 Manual de usuario

Meanwell

Meanwell RCP Series Manual de usuario

Meanwell

Meanwell DRA Series Manual de usuario

Meanwell

Meanwell CSP Series Manual de usuario

Meanwell

Meanwell AP Manual de usuario

Meanwell

Meanwell XLG-25 Series Manual de usuario

Meanwell

Meanwell DR-15-12 Manual de usuario

Meanwell

Meanwell RCP-1600 Series Manual de usuario

Meanwell

Meanwell HDR-15 Series Manual de usuario

Meanwell

Meanwell TDR-240-24 Manual de usuario

Meanwell

Meanwell HEP-1000 Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario