Maytag 12001908 Manual de usuario
(2)- (MAYTAG) TOP LOAD WASHER LID SWITCH KIT
#12001908.
A4141YlrAG
Instruction
Sheet 16010951
6 2612390-1201
This instruction sheet is to be used with:
REPAIR PART NO.: 12001908 (MPN 6 2306250)
DESCRIPTION: LID SWITCH KIT
CONTENTS: ]
TOOLS REQUIRED:
Phillips Screwdriver
The purpose of this instruction is to inform you of changes made to the switch, making the
switch no longer adjustable. The lid switch mechanism is designed to shut off the machine if
the lid is lifted no more than 1-7/8" and will allow the machine to start when the lid is less than
1/4" high. The plunger is only used with Atlantis washers.
Note: The new lid switch (identified with a grey button) is now non-adjustable. You
cannot adjust by pulling on the lid switch button.
Procedures
1. Disconnect power.
2. Remove console to gain access to lidswitch.
3. Liftlid slightlyto remove pressure onthe lid switch.
4. Remove lidswitch and installnew.
5. Reverse the afore mentioned steps.
6. Verify proper lid opening per measurements in the first paragraph.
7. If machine continues to not operate properly, please follow information shown on the follow-
mg page. ..... over
1
240 Edwards Street. Cleveland. TN 37311
DependableCareIPerforma L Washers: the enclosed lid switch is interchangable with the
lid switch used on those machines. Checking lid switch performance:
1. Ifthe switch functions, then you may need to adjust Ibend the unbalance lever slightly
backward.
2. Verify proper lid opening again.
If the switch shuts off the machine after the lid is o0ened more than 1-718", bend the
unbalance lever toward the back.
If the switch shuts off the machine when the lid is lower than 1/4". bend the unbalance
lever toward the front.
AUantis washers: In addition to the new lid switch, a change was also made to the length of
the plunger.
I. Verify proper lid opening again.
If the switch shuts off the machine after the lid is opened more than 1-7/8", check the
items listed below.
If the switch shuts offthe machil_e when the lid is lower than 1/4", use the enclosed
plunger and check the items listed below.
Other items that could be interpreted as a problem related to the lid switch, are as
follows:
Lid "oil canning" or chipped porcelain where the lid interfaces with the switch (or cam for
Atlantis). The lid may need to be replaced.
Lid hinpes or hinge balls either not inserted into the lid properly or cracked.
(Atlantis only) Hinge bushings mounted into the top may be cracked orworn.
(Atlantis only) Check the cam on the back flange of the lid to make sure itis not worn or
broken.
Tabla de contenidos
Otros manuales de Accesorios de lavandería de Maytag
Maytag
Maytag XHPC155XW Manual de usuario
Maytag
Maytag XHP1550VA0 Manual de usuario
Maytag
Maytag XHP1000XW Manual de usuario
Maytag
Maytag DC68-01052A Manual de usuario
Maytag
Maytag 12001736 Manual de usuario
Maytag
Maytag WHP0400VW Manual de usuario
Maytag
Maytag 12001454 Manual de usuario
Maytag
Maytag 201805 Manual de usuario
Manuales populares de Accesorios de lavandería de otras marcas
NSS
NSS Aero Plus Manual de usuario
GE
GE SBSD137 Manual de usuario
Truvox International
Truvox International Air Mover AM Manual de usuario
ALDI
ALDI Workzone Titanium+ LB-TFM01 Manual de usuario
MELICONI
MELICONI BASE SPACE BASKET Manual de usuario
American Dryer Corp.
American Dryer Corp. ML-758 Manual de usuario