Maxx Cold MCF-49FD Instrucciones de funcionamiento
Installation and Operation Guide
For
MCF-49FD, MCF-23FD
MCR-49FD, MCR-23FD
CONTENTS
SPECIFICATIONS
SERIAL NUMBER
1. SPECIFICATIONS
2. SERIAL NUMBER
3. INSTALLATION
4. CLEANING
5. CAUTION
6. BASIC OPERATION
6-1. REFRIGERATOR
6-2. FREEZER
7. REVERSIBLE DOOR ASSEMBLING METHOD
8. TROUBLE SHOOTING GUIDE
The serial number is located on the rating label which is on the left interior wall.
Please retain the unit's serial number for service purposes.
2
2
3
4
4
5 - 6
7 - 8
9 -10
11
Solid Door Refrigerators
MODEL COMP. H.P REFRIGERANT AMPERAGE POUNDS
MCR-23FD 1/3 R-134a 420W 271
MCR-49FD 1/2 R-134a 570W 370
Solid Door Freezers
MODEL COMP. H.P REFRIGERANT AMPERAGE POUNDS
MCF-23FD 1/3 R-134a 440W 284
MCF-49FD 1/2 R-404A 1340W 403
INSTALLATION
1. GOOD AIR CIRCULATION
- Be sure to avoid any object which will restrict exhausted air flow.
- Be sure that there is ample space so that air can flow through the rear of the unit.
- The back of the unit should be located no less than 5 inches from the wall.
2. PLACE ON STRONG GROUND
- Be sure the location chosen has a floor strong enough to support the total weight of the
cabinet and contents.
3. DO NOT PLACE NEAR HEAT SOURCE
- Be sure to avoid hot corner or location near stove, oven, or other heat source.
- High ambient temperature will make cooling efficiency lower.
4. INDOOR USAGE ONLY
- This equipment is intended for indoor use only.
5. STABILIZING
- Make sure the unit is installed in a stable condition with the front wheels locked while in
use.
6. LEVELING
- Be sure that the unit is level from front to back and side to side.
7. Unit should be on dedicated electrical circuit.
- Do not use extension cords
- Isolate the unit on an electrical circuit of proper size.
8. Place black plastic condensate pan thru back or front.
Make sure pads are installed upwards and drain hose is in pan.
CLEANING
CAUTION
1. CLEANING THE INTERIOR AND EXTERIOR
- The interior and exterior of the unit can be cleaned using warm water with soap.
- Do not use an abrasive cleaner because it will scratch the surface.
2. CLEANING THE CONDENSER FINS
- To maintain proper refrigeration performance, the Condenser coil must be free of dust,
dirt, and grease.
It will require to clean it periodically. Condenser fins should be cleaned, at least every
three months (90 days) or as needed.
3. CLEAN THE GASKET
- The door gasket should be cleaned frequently to maintain proper sealing. Use warm
water and a mild soap.
4. CHECK AFTER CLEANING
- Check the unit again for safety.
- Check that the unit is operating properly.
1. POWER CORD
- Be sure the power cord is connected to the proper voltage.
- Compressor warranties are void if compressor burns out due to improper voltage.
- A protected circuit of the correct voltage and amperage must be run for connection of the
line cord.
- Turn ‘ off ’ the power switch before disconnecting the power cord whenever performing
maintenance functions or cleaning the refrigerated cabinet.
- If the power cord of Refrigerator (Freezer) is damaged, it must be replaced by the
manufacturer or service agent or a similarly qualified person in order to avoid a hazard.
2. RE-STARTING
- If disconnected, wait 5 minutes before re-starting.
BASIC OPERATION
1. Plug in and turn on the power switch located on the bottom of the top grill.
The Display panel will be lighted. The compressor will begin to run.
2. The default temperature setting is 35ᵻ(+1ᴱ)
3. The compressor is automatically cycled by the electronic controller (PCB).
4. Temp. Control range 39ᵻ@28ᵻ( +7ᴱ@-3ᴱ)
5. The interior light is activated by the door switch when the door is opened.
6. Evaporator fan motor(s) will run after all doors are completely closed.
MCR-23FD
MCR-49FD
REFRIGERATOR
DISPLAY PANEL
1. UP / DOWN BUTTON (Temperature control button)
- By pushing the up/down button, you can set the inside temperature.
2. DOOR OPENING INDICATOR
- If door is opened, door opening indicator will be turned on.
- If the door is left open for 5 minutes an alarm will sound continuously.
- The alarm will stop immediately upon closing the door.
INSIDE TEMP.
TEMP. CONTROL BUTTON
DOOR OPENING
BASIC OPERATION
1. Plug in and turn on the power switch located on the bottom of the top grill.
The Display panel will be lighted. The compressor will begin to run.
2. The default temperature setting is -2ᵻ(-18ᴱ)
3. The compressor is automatically cycled by the electronic controller (PCB,
D-sensor).
4. The Defrost cycle is automatically controlled by the D-sensor and the PCB.
5. Temp. Control range 5ᵻ@-9ᵻ(-3ᴱ@-24ᴱ)
6. The interior light is activated by the door switch at the bottom of the grill when the
door is opened.
7. Evaporator fan motor(s) will run after all doors are completely closed.
MCF-23FD
MCF-49FD
FREEZER
DISPLAY PANEL
1. UP / DOWN BUTTON (Temperature control button)
- By pushing the up/down button, you can set the inside temperature.
2. DEFROST
- The electronic defrost controller is set at the factory to provide a defrost cycle every
6 hours.
- Once all frost is eliminated, the defrost control is changed to the freezer mode.
- The panel displays " " during the defrost.
3. DOOR OPENING INDICATOR
- If door is opened, door opening indicator will be turned on.
- If the door is left open for 5 minutes an alarm will sound continuously.
- The alarm will stop immediately upon closing the door.
INSIDE TEMP.
TEMP. CONTROL BUTTON
DOOR OPENING
MODEL : MCF-23FD / MCR-23FD
REVERSIBLE-DOOR ASSEMBLY METHOD
2. Taking apart of DOOR-ASSEMBLY
1) Follow steps ῡ~ Ὺin order at the PICTURE (B)
# Caution : Door is heavey
hinges are strong
loaded.
Use appropriate
care when
removing door.
1. REMOVAL OF TOP GRILL and GRILL ASSEMBLY
1) Remove the TOP GRILL by
removing securing screws.
Upper or downward located ῡ
in the PICTURE (A)
2) Remove GRILL by
removing securing screws.
connected
Left and right side located ῢ
in the PICTURE (A)
# Caution : Disconnect power
before reversing door, use caution with
cares associated with electronic control.
ῡ
ῢ
TOP GRILL
ῢM5*27 SCREW
ῩM5*27 SCREW
ΰDOOR-HINGE
UPPER
ῡDOOR-HINGE
STOP PIN
ῥDOOR-HINGE
BUSHING
ῧDOOR-HINGE
BUSHING
ῦDOOR
ASSEMBLY
ῤDOOR-HINGE
SHAFT-UPPER
GRILL
ASSEMBLY
PICTURE A
PICTURE B
ῨDOOR-HINGE
SHAFT-LOWER
ῪDOOR-HINGE
LOWER
3. Installation method of REVERSIBLE DOOR
4. Installing TOP GRILL and GRILL ASSEMBLY
1) Install the screws
at the location ῡ
on the top and bottom
of the top grill.
2) Install the screws
at the location ῢ
on the left and right
side of the grill
assembly.
1) After reversing 180 degree DOOR ASSEMBLY ῦ, locate the HANDLE in the
desired side.
2) Assemble in the following
order.
- After assembling ΰῢL assemble ῤῥ
- Insert into ῤDOOR ASSEMBLY of ῦ
- After inserting ῧῨ, secure ΰῩ
- Insert reversible for suitable spring elasticity
# Attention : Securely tighten all fastners.
ῩM5*27 SCREW
ΰDOOR-HINGE
LOWER
ῨDOOR-HINGE
SHAFT-LOWER
ῦDOOR ASSEMBLY
ῥDOOR-HINGE BUSHING
ῡDOOR-HINGE STOP PIN
ΰDOOR-HINGE UPPER ῢM5*27 SCREW
ῤDOOR-HINGE
SHAFT-UPPER
ῧDOOR-HINGE
BUSHING
ῡ
ῢ
PICTURE C
PICTURE D
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
Otros manuales de Refrigerador de Maxx Cold
Maxx Cold
Maxx Cold MXCR-23FD Manual de usuario
Maxx Cold
Maxx Cold MCR-23FD Instrucciones de funcionamiento
Maxx Cold
Maxx Cold X Series Manual de usuario
Maxx Cold
Maxx Cold MXSR29S Manual del propietario
Maxx Cold
Maxx Cold MXM1-2R Manual de usuario
Maxx Cold
Maxx Cold MCF27U Manual del propietario
Maxx Cold
Maxx Cold MCR27U Manual de usuario
Maxx Cold
Maxx Cold MXCB48 Manual de usuario
Maxx Cold
Maxx Cold X Series Manual de usuario
Maxx Cold
Maxx Cold MXCR-23FDHC Manual de usuario
Maxx Cold
Maxx Cold X Series Manual de usuario
Maxx Cold
Maxx Cold SELECT MXSR29U Manual del propietario
Maxx Cold
Maxx Cold MCR3U-O Manual de usuario
Maxx Cold
Maxx Cold MCR3U Manual de usuario
Maxx Cold
Maxx Cold MXM1-12R Manual de usuario
Maxx Cold
Maxx Cold MXM1-12RB Manual de usuario
Maxx Cold
Maxx Cold MXCR-19FDHC Manual de usuario
Maxx Cold
Maxx Cold MXX-23FHC Manual de usuario
Maxx Cold
Maxx Cold MXM1-2.5FHC Manual de usuario
