maxon motor EC 20 Manual de usuario
maxon motor
maxon EC motor EC 20 flat with integrated electronics
Doc. no. 903155
Operating Instructions Edition September 2010
The EC 20 flat motor with integrated electronics is a brushless, speed-controlled 1-quadrant drive. The EC 20 flat
can be supplied in a 2 watt or 5 watt version.
Functions:
• Commutation with Hall sensors
• Digital speed control
• Speed range: 200 rpm – 7000 rpm (depends on version)
• Current restriction fixed
• Overvoltage and undervoltage switch-off
• Overvoltage protection
• Blockage protection, temperature monitoring
• Inverse polarity protection
2-wire version
• Speed proportional to input voltage
5-wire version
• Set value speed target through analog signal 0 ... 10 V
• 2-wire operation possible
• Versions: - «Enable» TTL level compatible
- Direction pre-selection «cw/ccw» TTL level compatible
• Speed monitor supplies frequency signal proportional to speed
Table of contents
1 Safety instructions ....................................................................................................................................... 2
2 Technical data .............................................................................................................................................. 3
3 Minimum external wiring .............................................................................................................................. 7
4 Description function of inputs and outputs 5-wire version ......................................................................... 10
5 Description function of 2-wire version ........................................................................................................ 13
6 Protective functions.................................................................................................................................... 14
7 Installation instructions .............................................................................................................................. 15
8 EMC-compliant installation ........................................................................................................................ 15
9 Trouble shooting ......................................................................................................................................... 16
10 Dimensions ................................................................................................................................................ 17
11 Glossary..................................................................................................................................................... 18
These instructions are available on the Internet as a PDF file at www.maxonmotor.com, under “Service & Down-
loads”. Doc. no. 903155_PDF_E.
Order Number: 350795, 350776, 350796, 350778, 350794, 349694, 370413, 370412, 350834, 350804,
350835, 350805, 350806, 349731, 370416, 370415
maxon motor
2 maxon EC motor
EC 20 flat with integrated electronics Operating Instructions
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
1 Safety instructions
Skilled personnel
Only skilled, experienced personnel should install and start the equipment.
Statutory regulations
The user must ensure that the EC 20 flat with integrated electronics and the
components belonging to it are assembled and connected according to local
statutory regulations.
Additional safety equipment
Any electronic equipment is, in principle, not fail-safe. Machinery and equip-
ment should therefore be fitted with equipment-independent monitoring and
safety features. There must be guarantees that the drive or the entire piece of
equipment can be run safely if the equipment fails, if it is used incorrectly, if
the control unit fails, if the cable breaks etc.
Repairs
Repairs may only be carried out by authorised personnel or the manufacturer.
It is dangerous for users to open the unit or carry out any repairs.
Danger
Users must ensure that no apparatus is connected to the electrical supply
during installation of the EC 20 flat with integrated electronics! After switching
on, do not touch any live parts!
Max. supply voltage
Make sure that the supply voltage is between 10 VDC and 28 VDC. Perma-
nently switched on voltages above 30 VDC destroy the unit.
Electrostatic sensitive components
During transportation, assembly and operation, contact of the EC 20 flat with
integrated electronics with electrostatically charged components or persons
must be avoided. The integrated electronics can be destroyed by electrostatic
discharges.
Temperature
The temperature of the housing, flange or components may exceed 60°C
during operation.
maxon EC motor 3
maxon motor
Operating Instructions EC 20 flat with integrated electronics
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
2 Technical data
2.1 Order number
350795 (IP40), 350776 (IP00) 2-wire version, nominal speed 3000 rpm, 2 Watt
350796 (IP40), 350778 (IP00) 2-wire version, nominal speed 6000 rpm, 2 Watt
350794 (IP40), 349694 (IP00) «Enable» 5-wire version, nominal speed 6000 rpm, 2 Watt
370413 (IP40), 370412 (IP00) «cw/ccw» 5-wire version, nominal speed 6000 rpm, 2 Watt
350834 (IP40), 350804 (IP00) 2-wire version, nominal speed 3000 rpm, 5 Watt
350835 (IP40), 350805 (IP00) 2-wire version, nominal speed 6000 rpm, 5 Watt
350806 (IP40), 349731 (IP00) «Enable» 5-wire version, nominal speed 6000 rpm, 5 Watt
370416 (IP40), 370415 (IP00) «cw/ccw» 5-wire version, nominal speed 6000 rpm, 5 Watt
2.2 Motor data 2 Watt at 24VDC
Order number IP40 (with housing) 350795 350796 350794/370413
Order number IP00 (without housing) 350776 350778 350794/370412
Nominal voltage VDC 24 24 24
No load speed rpm 3000 6000 6000
No load current mA 14.5 19.8 19.8
Nominal speed rpm 3000 6000 6000
Nominal torque mNm 3.74 3.74 3.74
Nominal current mA 196 278 278
Max. torque mNm 5 5 5
Max. current mA 330 330 330
Max. efficiency % 25 37 37
500
1000
1500
2000
2500
3000
3500
4000
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
n [min-1]
M [mNm]
Vcc = 28V
Vcc = 24V
Vcc = 18V
Vcc = 12V
Vcc = 10V
Picture 1: Operating range n = f (M)
2-wire version, nominal speed 3000 rpm, order number 350795, 350776
1000
2000
3000
4000
5000
6000
7000
8000
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
n [min-1]
M [mNm]
Vcc = 28V
Vcc = 24V
Vcc = 18V
Vcc = 12V
Vcc = 10V
Picture 2: Operating range n = f (M)
2-wire version, nominal speed 6000 rpm, order number 350796, 350778
maxon motor
4 maxon EC motor
EC 20 flat with integrated electronics Operating Instructions
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
1000
2000
3000
4000
5000
6000
7000
n [min-1]
M [mNm]
0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
set value = 10V
set value = 5V
set value = 1V
Vcc = 12V
Vcc = 10V
Picture 3: Operating range n = f (M)
5-wire version, order number 350794 and 349694, 370413, 370412
If the supply voltage is reduced, the torque and/or speed may change.
2.3 Motor data 5 Watt at 24VDC
Order number IP40 (with housing) 350834 350835 350806/370416
Order number IP00 (without housing) 350804 350805 349731/370415
Nominal voltage VDC 24 24 24
No load speed rpm 3000 6000 6000
No load current mA 18.8 23.1 23.1
Nominal speed rpm 3000 6000 6000
Nominal torque mNm 7.5 7.5 7.5
Nominal current mA 258 394 394
Max. torque mNm 10.3 10.3 10.3
Max. current mA 458 580 580
Max. efficiency % 42 55 55
500
1000
1500
2000
2500
3000
3500
4000
123456789101112
n [min-1]
M [mNm]
Vcc = 28V
Vcc = 24V
Vcc = 18V
Vcc = 12V
Vcc = 10V
Picture 4: Operating range n = f (M)
2-wire version, nominal speed 3000 rpm, order number 350834, 350804
maxon EC motor 5
maxon motor
Operating Instructions EC 20 flat with integrated electronics
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
1000
2000
3000
4000
5000
6000
7000
8000
123456789101112
n [min-1]
M [mNm]
Vcc = 28V
Vcc = 24V
Vcc = 18V
Vcc = 12V
Vcc = 10V
Picture 5: Operating range n = f (M)
2-wire version, nominal speed 6000 rpm, order number 350835, 350805
1000
2000
3000
4000
5000
6000
7000
n [min-1]
M [mNm]
set value = 10V
set value = 1V
Vcc = 12V
Vcc = 10V
123456789101112
Vcc = 18V
Vcc = 24V
set value = 5V
Picture 6: Operating range n = f (M)
5-wire version, order number 350806, 349731, 370416, 370415
If the supply voltage is reduced, the torque and/or speed may change.
2.4 Controller data
Version 2-wire 2-wire 5-wire
Nominal speed 3000 rpm 6000 rpm 6000 rpm
Control variable speed speed speed
Supply voltage VCC V 10 … 28 10 … 28 10 … 28
Set value speed input V = VCC = VCC 0.33 … 10.8
Scale set value speed input rpm/V 125 250 600
Speed range rpm 1250 … 3500 2500 … 7000 200 … 6480
Max. acceleration rpm/s 3000 6000 6000
Direction of rotation (CW = clockwise) cw cw cw
Direction of rotation presetting «cw/ccw» cw/ccw
2.5 Thermal data
Version 2 Watt 5 Watt
Thermal resistance housing-ambient K/W-1 13 13
Thermal resistance winding-housing K/W-1 10 7.5
Thermal time constant winding s 2.38 10.3
Thermal time constant motor s 133 72.6
Max. permissible winding temperature °C +125 +125
Max. temperature of electronics °C +105 +105
maxon motor
6 maxon EC motor
EC 20 flat with integrated electronics Operating Instructions
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
2.6 Mechanical data (preloaded ball bearings)
Version 2 Watt 5 Watt
Rotor inertia gcm23.2 5.1
Axial play at axial load < 2 N mm 0 0
> 2 N mm 0.14 0.14
Radial play preloaded preloaded
Max. axial load (dynamic) N 1.8 1.8
Max. axial load (static) N 20 20
static, shaft supported) N 200 200
Max. radial load 5 mm from flange N 11 12
Weight of motor gr 30 37
2.7 Connection (input/output)
Cable Description Connection Value
Red Supply voltage VCC Supply 10 … 28 VDC
Black Gnd Supply Ground
White (only 5-wire operation) Set value speed input Input 0.33 … 10.8 VDC
Green (only 5-wire operation) Monitor speed n Output 6 counts per turn
Version Enable
grey (only 5-wire operation) «Enable» Input 2.4 … 28 VDC
Version Direction
grey (only 5-wire operation) «cw/ccw»Input 2.4 … 28 VDC
Wire size AWG28 =ˆ 0.09 mm2
2.8 Protective functions
Inverse-polarity protection up to max. 30 VDC
Blockage protection cut off with blocked motor shaft after 2 s
Low voltage protection cut off at VCC < 8.5 V
High voltage protection cut off at VCC > 29.5 V
Thermal control of the power stage cut off at T > 100 °C typ.
High voltage protection (transient) 150 mWs
2.9 Ambient conditions
Temperature range -40 ... +40 °C
Range with reduced performance +40 ... +85 °C
Temperature range bearing -40 ... +85 °C
Humidity range not condensing 20 … 80 %
2.10 Voltage supply
Ripple < 5%
Output current depending on the load, recommendation >_ 1 A
Max. output voltage 29 VDC
Min. output voltage 9.5 VDC
maxon EC motor 7
maxon motor
Operating Instructions EC 20 flat with integrated electronics
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
3 Minimum external wiring
3.1 5-wire version
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
Supply
voltage
10 ... 28 VDC
14k / 0.1 W 10k / 0.1 W
Supply
voltage
10 ... 28 VDC
Values for 24 VDC operating voltage
14k / 0.1 W 10k / 0.1 W
Values for 24 VDC operating voltage
red
black
white
green
grey
red
black
white
green
grey
red
black
white
green
grey
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
Picture 7: Example for speed set value and release «Enable» or direction «cw/ccw» (depending
on the variant) through external power source.
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
Supply
voltage
10 ... 28 VDC
14k / 0.1 W 10k / 0.1 W
Supply
voltage
10 ... 28 VDC
Values for 24 VDC operating voltage
14k / 0.1 W 10k / 0.1 W
Values for 24 VDC operating voltage
red
black
white
green
grey
red
black
white
green
grey
red
black
white
green
grey
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
Picture 8: Example for speed set value with external power source and release «Enable» or
direction «cw/ccw» (depending on the variant) with potentional-free contact.
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
Supply
voltage
10 ... 28 VDC
14k / 0.1 W 10k / 0.1 W
Supply
voltage
10 ... 28 VDC
Values for 24 VDC operating voltage
14k / 0.1 W 10k / 0.1 W
Values for 24 VDC operating voltage
red
black
white
green
grey
red
black
white
green
grey
red
black
white
green
grey
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
Picture 9: Example for speed set value with external potentiometer and release «Enable» or
direction «cw/ccw» (depending on the variant) with external power source.
maxon motor
8 maxon EC motor
EC 20 flat with integrated electronics Operating Instructions
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
Set value
Speed
0 ... 10 VDC
Supply
voltage
10 ... 28 VDC
14k / 0.1 W 10k / 0.1 W
Supply
voltage
10 ... 28 VDC
Values for 24 VDC operating voltage
14k / 0.1 W 10k / 0.1 W
Values for 24 VDC operating voltage
red
black
white
green
grey
red
black
white
green
grey
red
black
white
green
grey
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
«Enable» or «cw»
2.4 ... 28 VDC
«Disable» or «ccw»
0.0 ... 0.8 VDC
«Enable» or «cw» if closed
«Disable» or «ccw» if open
Picture 10: Example for speed set value with external potentiometer and release «Enable» or
direction «cw/ccw» (depending on the variant) with potentional-free contact.
3.2 5-wire version in 2-wire operating mode
2-wire operating mode can be simulated by short-circuiting the terminals set
value speed input and speed monitor output. Speed is proportional to the
supply voltage (see picture 17).
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
red
black
Supply
voltage
10 ... 28 VDC
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
red
black
white
green
grey
«cw»
2.4 ... 28 VDC
«ccw»
0.0 ... 0.8 VDC
«cw» if closed
«ccw» if open
Picture 11: Example for 5-wire version in 2-wire operating mode
Version direction «cw/ccw»: the direction of rotation can be selected at the
grey wire.
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
red
black
Supply
voltage
10 ... 28 VDC
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
red
black
white
green
grey
«cw»
2.4 ... 28 VDC
«ccw»
0.0 ... 0.8 VDC
«cw» if closed
«ccw» if open
Picture 12: Example for 5-wire version direction «cw/ccw» in 2-wire operating mode.
maxon EC motor 9
maxon motor
Operating Instructions EC 20 flat with integrated electronics
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
Version direction «cw/ccw»: the direction of rotation can be selected at the
grey wire.
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
red
black
Supply
voltage
10 ... 28 VDC
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
red
black
white
green
grey
«cw»
2.4 ... 28 VDC
«ccw»
0.0 ... 0.8 VDC
«cw» if closed
«ccw» if open
Picture 13: Example for 5-wire version direction «cw/ccw» in 2-wire operating mode.
3.3 2-wire version
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
Supply
voltage
10 ... 28 VDC
red
black
Supply
voltage
10 ... 28 VDC
Supply
voltage
10 ... 28 VDC
red
black
white
green
grey
red
black
white
green
grey
«cw»
2.4 ... 28 VDC
«ccw»
0.0 ... 0.8 VDC
«cw» if closed
«ccw» if open
Picture 14: Example for 2-wire version
maxon motor
10 maxon EC motor
EC 20 flat with integrated electronics Operating Instructions
September 2010 Edition / document number 903155_PDF_E - 07 / subject to change
4 Description function of inputs and outputs 5-wire version
4.1 Set value speed input
Motor speed is set with an analog voltage at the set value speed input.
The set value speed input is protected against overvoltage.
Pin allocation Cable white
Input voltage range 0 ... +10.8 V (based on GND)
Input impedance 62 kW (range 0 ... +21.9 V)
47 kW (range 21.9 V... +30 V)
Continuous overvoltage protection -30 V ... +30 V
47k
15k
1µF
white
set value speed
12k
100k
grey
6’000
0
0
200
10.0
0.17 0.33
3’000
510.8
6’480
7’000
Speed
[rpm]
0
0
28
2’500
10
6’000
24
Enable
3’500
0
0
28
1’250
10
3’000
24
Operating voltage [V]
Speed
[rpm]
Operating voltage [V]
Speed
[rpm]
Operating voltage [V]
12k
100k
grey
Direction «cw/ccw»
Picture 15: Wiring set value speed
The speed set value is set with the voltage at the speed set value input. The
set speed is controlled by the amplifier. Changes to speed set value are re-
stricted by the maximum acceleration (see section 2.4).
To activate the output stage in the «enable» version, the voltage at the enable
input must be higher than 2.4 V, while the speed set value must be above
0.17 V.
With the «cw/ccw» direction pre-selection version, the output stage is activa-
ted when the speed set value is higher 0.17 V.
Set value input area Function Comments
0 V … 0.17 V «Disable» Power stage switched off.
0.17 V … 0.33 V Operation at minimum speed
(200 rpm)
If «enable» higher than 2.4 V for version
«Enable».
0.33 V … 10.8 V Linear speed setting between
200 rpm and 6480 rpm
fn
Vn
10
10
600
Monitor n actual
actual Monitor n
target target
$
=
=
=
If «enable» higher than 2.4 V. In speed
range between 200 rpm and 300 rpm,
control accuracy of the speed controller
is restricted. The speed can vary from
the specified set value depending on the
load and supply voltage.
Vtarget = Set value voltage
ntarget = Desired speed
Tabla de contenidos
Otros manuales de Motor de maxon motor
