Max Skin 2 Manual de usuario

INSTRUCTION MANUAL

kin

TABLE OF CONTENTS

CHAPTER 1: Technical Data 3

CHAPTER 2: Introduction 4

CHAPTER 3: Operating Mode Skin 2 6

CHAPTER 4: Maintenance and Lubrication 8

CHAPTER 5: Assembling / Disassembling 9

CHAPTER 6: Service and Warranty 10

CHAPTER 7: Terms and conditions 11

INDEX

WARNING:

1) This machine is a precision instrument. Do not drop it or subject it to

physical shock.

2) Do not lubricate the motor and bearings, they are maintenance-free.

3) Do not use the machine over 12 volts DC.

4) Do not use cleaners containing solvents to clean the body of the

machine, do not use spray cleaners directly on the machine. To clean

the machine wipe it with a well-wrung wet cloth or clean wipes.

5) Do not autoclave, do not ultrasonic clean.

6) Use a Power Unit with not more than 2 Ampere and do not

exceed 12 volts.

1 Technical Data

• Voltagerating:12voltDC

• RecommendedInputVoltage:0–12voltDC

• Revolutionsperminute:0–9300rpm/min

• Stitchespersecond:0–155/sec.

• Currentupto:0,35A(thermallimit)

• Needleexcursion:3,7mm(serialexcenter)

• Availableexcenters:2,6-3,7-4,5-5,5mm

• Excursionofneedlesuspension:0–3mm

• MaximumTubeDiameter:8mm

• Weight:90grams

• Dimensions:height78mm,width87mm,thickness23mm

• Supportsupto55Magnumneedles

• Motor:ThismachineisequippedwithaSwissmotor

• DesignedandentirelymanufacturedinItalybyIMaxInternational

RCA

TighteningBar

PistonRod

NeedlebarPin

Backbindingclip-cord

negativepole

GIVECap

adjustmentofneedlehittingstrength

Frame

Backbindingclip-cord

positivepole MotorHousing

TubeClosingScrew

Excenter

SKIN 2 is a new conception rotary machine for tat-

tooing. The main innovations are:

2 INTRODUCTION

GIVE adjustment of needle throw and its intensity.

You have the possibility to adjust the strength of

the needle throw (GIVE). This adjustment allows to

set the machine “harder” adapted for lining or

“softer” adapted for colouring, lling and shading.

The adjustment notches on the cap of the GIVE

allow intermediate set ups.

Tightening bar.

No more rubber bands

are needed for needle bar

adjustment.

ATTENTION, tighten it lightly

and don’t push more than

necessary, don’t apply too

much pressure to the needle

bar.

RCA Connection.

In addition to the traditional

clip-cord connection, the SKIN 2

is provided with a RCA

connection. The RCA connection

ensures a current ow much more

stable.

Adjustment of needle excursion.

Following replacement excenters

for needle excursion adjustment are

available: 3,7mm (serial excenter),

2,6 - 4,5 - 5,5 mm (replacement

excenters are available separately).

Lightweight, silent, vibrations are reduced to a minimum.

Thanks to the Swiss Motor DC-Micromotors, high quality

ball-bearings and the ultra-light materials used, the SKIN 2

is lightweight, silent and the vibrations are reduced to a

minimum.

2 INTRODUCTION

3 OPERATING MODE SKIN 2

Youhavethepossibilitytoadjustthestrength

oftheneedlethrow(GIVE).Thisadjustment

allowstosetthemachine“harder”adaptedfor

liningor“softer”adaptedforcolouring,lling

andshading.Theadjustmentnotchesonthe

capoftheGIVEallowintermediatesetups.

N.B. The machine comes with Liner Setting, the adjustment screw

is tightened completely and the smallest notch on the cap matches

with the reference notch on the machine frame. It is recommended

to not fully tighten the screw GIVE but leave always 2 or 3

notches unscrewed and put there the smallest notch on the cap.

If the machine does not run the screw GIVE is too tightened,

unscrew a little bit.

GIVE adjustment screw of needle intensity

Shader Setting (soft)

By turning the cap anti-clockwise, the adjustment screw of the needle throw

GIVE is loosened and the setting becomes softer, more you loosen the screw,

more the machine setting becomes SOFTER. It is possible to loosen the screw

up to 2 complete rotations (2 times 360°). N. B. Never loosen the screw more

than 2 complete rotations or the mechanism will disassemble.

Liner Setting (hard)

By turning the cap clockwise, the adjustment screw of the needle throw GIVE

is tightened and the setting becomes harder, more you x the screw, more the

machine setting becomes HARDER. ATTENTION: Do not overtighten, do not

force to screw over the limit.

3 OPERATING MODE SKIN 2

Thisinnovationallowstoadjustthebartensionwithoutusingrubber

bands.Attention:placethetighteningbarslightlyontotheneedle

bar,itissufcientoncethesmallwheelbeginstorotate.Avoidan

excessivepressureontheneedlebar.

Tightening Bar

New Skin 2 model R2 do not require lubrication. To ﬁnd out

if your Skin 2 is a model R2 check on the box labeled R2.

Every80/100hoursofuselubricatethepistonusingVASELINE,alubricating

creammadeofpureparafnformachineutensils.Forlubricationpushdown

thepiston,passthroughthecoiloftheneedlebarpin,applyathinlayeronto

thepin(above)andpiston(below)usingasmallhexwrench.Lubricatealsoin

frontandbehindthepistonwhereitjoinsthepistonrod.Donotapplytoomuch

lubricant,asmallquantityissufcient.Turnonthemachine,regulatethepower

unitto11voltandrunthemachineforafewminutesinorderthatthelubricate

isdistributedtothewholepiston.

4 Maintenance and Lubrication

Lubricate

every80/100hours

5 Assembling / Disassembling

Assembling / Disassembling

of excenter and piston rod.

Toremovetheexcenterfromthemotorandthe

pistonrodfromthepiston,youneedhexwrenches

forM0.9andM1.3screws.Loosengentlytheset

screwwhichxesthepistonrodontheexcenter,

removeconnectingplug,rotatethepistonrodon

theside,unscrewthescrewthatxestheexcenter

tothemotorhousingandremoveexcenter.

Toremovethepistonrod,pushdownthepiston,

unscrewthescrewthatxesthepistonrodtothe

pistonandnallyremovethepistonrodfromthe

piston.Forassemblinginversetheoperation.

ATTENTION:

1.Donottightenthescrewstoomuchasyoumightstripthethreads!

2.Tomountthepistonrodontothepistontightthescrewcompletely,thenturnbackhalf

rotationtherewithaslidingmovementofthepistonrodonthepistonisgiven.

Alignment of the piston rodLoosenthescrewthatxesthepistonrodontothe

excenter.Switchonthemachineforafewsecondsinorderthatthepistonrodcanbe

aligned.Fixthescrewthatxesthepistonrodontotheexcenter.Donottightenthescrew

toomuchasyoumightstripthethreads.

Disassembling of the piston

Afterhavingremovedthepistonrodfromthepiston,removethecapoftheGIVE,

loosentheGIVEscrewcompletely.Loosenthesetscrewthatxestheneedlebar

pinontothepiston.Removethepistonfromabovepayingattentionthatthe

springdoesn’tgetlost.

Assembling of the piston

Putthespringofthepistonintoitspositionoftheframe.

Insertthepistonaligningthespringwithitslocationon

thepiston.Inserttheneedlebarpinintothepiston,the

distancebetweenpinandframeshouldbe0,1mmin

ordertoavoidfrictionandnoiseduringtheuse.Screw

thesetscrewthatxesthepinontothepiston.Insertthe

GIVEspringandtightentheGIVEscrewcompletely.Mountthecap.

6 Service and Warranty

ForsimplemaintenanceofyourSKIN2youcanpurchasepartsand

utensilsonwww.imaxshop.comoryoucancall+390541642160.

ForaccuratemaintenanceyoucouldturnyourSKIN2backtoIMax

InternationalS.r.l.,VialeEmilia41,47838Riccione,Italy.

SKIN2includesa12monthwarrantyfromthedateofpurchase.

Thewarrantyisvalidonlyagainstmanufacturingdefectsanddoes

notcoverabrasioncausedbynormaluse.Themovingpartsare

subjecttoabrasionandarenotwarranted.

The warranty becomes void in following cases:

1.Themotorhousinghasbeenopened.Foranyoperationregarding

themotorhousingturnthemachineback.

2.Inputtensionhasbeenexceededoverthelimitof14volts.

Attention:thismachineisequippedwitha0-12voltsmotor.

3.Themachineoranyparthasbeensterilisedorcleanedin

sterilizers,autoclavesorultrasoniccleaners.

4.Damageofthemachineoroneofitscomponentsbyimproper

useorcarelessness.

5.Abnormaluse,carelessness,excessiveuse,forlackoflubrication.

Tabla de contenidos

Otros manuales de Herramientas eléctricas de Max

Max

Max 45505 Manual de usuario

Max

Max HN75 Manual de usuario

Max

Max TA551A/16-11 CE Instrucciones de funcionamiento

Max

Max GS690RH Instrucciones de funcionamiento

Max

Max RE-BAR-TIER RB517CE Instrucciones de funcionamiento

Max

Max CN665D Instrucciones de funcionamiento

Max

Max SuperFramer CN890F2 Instrucciones de funcionamiento

Max

Max 71311 Manual de usuario

Max

Max CN890B Instrucciones de funcionamiento

Max

Max 61011 Manual de usuario

Max

Max PowerLite HN65 Instrucciones de funcionamiento

Max

Max RB655 Instrucciones de funcionamiento

Max

Max GS738C LT Instrucciones de funcionamiento

Max

Max PowerLite HN65 Manual de instrucciones

Max

Max SN883RH Instrucciones de funcionamiento

Max

Max RB655 Instrucciones de funcionamiento

Max

Max 61018 Manual de usuario

Max

Max CN452S Instrucciones de funcionamiento

Max

Max HS90A Instrucciones de funcionamiento

Max

Max CN238 Instrucciones de funcionamiento

Max

Max TA116/21-13 Instrucciones de funcionamiento

Max

Max CN55 Instrucciones de funcionamiento

Max

Max RE-BAR TIER RB518 Instrucciones de funcionamiento

Max

Max Rebartier RB398S Manual del operador

Manuales populares de Herramientas eléctricas de otras marcas

AEG

AEG OMNI-JS Manual de usuario

SIP

SIP 01533 Manual de usuario

Ribimex

Ribimex PRS499 Manual de usuario

3M Fiber Optic Connector Crimp Tool Manual de usuario

Ryobi

Ryobi P524 Manual de usuario

ROJEK

ROJEK FSN 300A Manual de usuario

Kemper

Kemper 1740PRO Manual de usuario

WABCO

WABCO OptiTire Manual de usuario

EINHELL

EINHELL TE-MS 18/210 Li Manual de usuario

Orgapack

Orgapack OR-T 85 Guía rápida

TOUGHCUT

TOUGHCUT Diamond 400 Manual de usuario

Yaros

Yaros PB-3603 Manual de usuario

Fein

Fein BSS 2.0 E Guía de configuración

Baileigh Industrial

Baileigh Industrial SS-2725 Manual de usuario

Milwaukee

Milwaukee 2674-20 Manual de usuario

Fein

Fein BLs 1.6 Manual de usuario

Princess

Princess Electric Multi Sharpener Manual de usuario

FOREDOM

FOREDOM K.1050 Manual