Matsusada Precision PZM-0.12BS Manual de usuario

Instruction Manual

MODEL PZM-0.12BS

B/N 058.9.010 *058.9.010*Rev. 0.2

Note

◆No part of this publication may be reproduced, stored in a retrieval system, or

transmitted, in any form, or by any means, mechanical, electronic, photocopying,

recording, or otherwise, without the prior written permission of Matsusada Precision.

◆No patent liability is assumed with respect to the use of the information contained

herein. Moreover, because Matsusada Precision is constantly striving to improve its

high-quality products, the information contained in this manual is subject to change

without notice. Every precaution has been taken in the preparation of this manual.

Nevertheless, Matsusada Precision assumes no responsibility for errors or omissions.

Neither is any liability assumed for damages resulting from the use of the information

contained in this publication.

Trademarks

◆Company names and product names in this document are the trademarks or registered

trademarks of their respective companies.

Warranty

◆For details, refer to the following website.

https://www.matsusada.com/support/manufacturer_warranty.html

PZM-0.12BS

Matsusada Precision

For Safe Use of the Product

◆Introduction

The product generates high-voltage and high-energy.

Therefore, wrongly handling or operating the product may result in death or serious injury and maybe

property damage as well. In order to use the product safely, read the instruction manual thoroughly

before use to understand how to use and operate it properly.

Please note that we will not be held responsible for any damage or loss caused by not following the

warnings, cautions, and procedures described in the manual.

Keep the manual with you so that you can read it whenever you want.

◆Symbols

Symbols are used in the manual and product, which indicate precautions to be observed for safe use.

Understand these symbols first and then read the manual thoroughly.

Some symbols below are not used in products.

Indicates a potentially hazardous situation, which, if not avoided, may

result in serious injury or death.

Indicates a potentially hazardous situation, which, if not avoided, may

result in minor or moderate injury or in property damage.

Indicates danger/warning/caution. Refer

to the instruction manual when this

symbol appears on the unit.

Frame or chassis terminal

Indicates the possible danger of electric

shock under specific conditions, which

may result in serious injury or death.

Ground terminal

High Temperature Caution:

Indicates the possible danger of injury by

high temperature under specific

conditions.

Power ON

Indicates general prohibitions, including

warnings.

Power OFF

Indicates what must be followed.

Standby

Protective earth terminal (ground terminal

for preventing electric shock)

Bistable push button switch

Indicates the possible danger of death if

you drink it and burns or blindness if it

attaches.

Bistable push button switch

OFF

Indicates the possible danger of exposure

to radiation.

Alternative Current

PZM-0.12BS

Matsusada Precision

◆Understand the risks.

The Product generates high-voltage and high-energy.

The product is designed for electrical engineers or the equivalents who install, wire, and operate it.

Read the instruction manual thoroughly before use and familiarize yourself with the proper use and

danger of the product.

◆Make sure to allow only specific people to handle the product.

Make sure to allow only the following people to handle the product:

1. who are electrical engineers or the equivalents and have already familiarized themselves with the

proper use and danger of the product, or

2. who are electrical engineers or the equivalents and have already been trained by the above-

mentioned people, or

3. who work under the supervision of the above-mentioned people.

If people other than those listed above install, wire, or operate the product, it may cause electric

shock, burnout, or injury.

◆Do not open or remove the case or panel of the product.

Do not disassemble, repair, or modify the product by yourself. High-voltage is applied to the inside of

it.

Otherwise, it may cause electric shock, fire, or malfunction.

Moreover, if you do it, the safety and functions are not covered with the warranty.

◆The product does not suit to install and use in places where children may be present.

The product is designed to be installed in places such as factories or laboratories. Do not install and

use it where children may be present.

◆Make sure to ground it.

When the product has a protection ground terminal or GND terminal, make sure to ground it.

When the AC line input of it is an inlet type, connect the attached power cable or a power cable

suitable for your area to an outlet with the ground. Otherwise, it may result in electric shock or fire.

◆Regarding power cable

When a power cable is enclosed or attached to the product, do not use it for other products.

When no power cable is enclosed with the product, prepare the power cable suitable for the usage

environment and area by yourself.

◆Regarding the connection of power cable

Electrical engineers or the equivalents who have already been familiarized with the proper use and

danger of the product should connect the power cable to the AC input by referring to the instruction

manual.

Regarding products that have acquired the safety standard, check the page describing the over-

voltage categories too.

◆Do not process or damage power cables

It may result in electric shock or fire.

◆Regarding the input voltage

Check the page describing the input terminals and input voltage in the instruction manual.

Do not provide any voltage out of the specifications.

PZM-0.12BS

iii

Matsusada Precision

◆Regarding the fuse

The product builds in a protective fuse. In the case where a fuse holder is arranged outside of the

product, you can replace it by yourself. Refer to the instruction manual to replace it.

In the case where a fuse holder is not arranged outside of the product, you cannot replace it by

yourself.

In this case, do not open the case or panel of the product and contact us.

◆The product is designed for indoor use.

Use the product indoors only, not outdoors. Even indoors, do not use it if there is a possibility of

water leakage, flooding, or snow covering.

◆Regarding operating temperature and humidity

Use the product within the range of the specifications describing in the instruction manual.

Do not use it in a place where the ambient temperature exceeds the specified range or a closed

place.

◆Do not install the product in places where condensation may occur.

Otherwise, insulation deteriorates and it may cause electric shock, fire, or malfunciton.

◆Do not place anything on top of the product.

Otherwise, they may fall or tumble from it.

◆Do not put anything into the product.

Do not put foreign objects such as metal or liquid into the product through the air inlets, air outlets,

or other openings. Otherwise, it may result in electric shock, fire, or malfunction.

◆Operate the product with the right hand.

Use only your right hand to operate the product and keep your left hand away from it, which can

reduce the risk of electric current flowing through the left hand to the vital organs of the body in the

event of an electric shock.

◆Do not touch the wiring/load connected to the output and any terminals/connectors during

the operation or just after turning output off.

Very high-voltage is on the terminals and connectors during the operation and even just after the

output is turned off. Touching them may result in serious injury or death by electric shock.

The terminals here mean all terminals like input and output terminals and terminals for

communications and remote controls.

◆Turn off the product before touching the wiring/load connected to the product and any

terminals/connectors on the product and cut it off from the AC input.

Before touching the terminals/connectors and wiring/load, turn off the product and unpug the AC

input cable from the outlet or turn off the AC input breaker. Then, check there is no voltage remained

using a tester.

Since the output and sense terminals are connected to condensers in it, there is high-voltage

remained on them even just after it is turned off.

In order to avoid electric shock, ground the terminals to discharge using a short-circuit grounding

apparatus and check the voltage again.

The terminals here mean all terminals like input and output terminals and terminals for

communications and remote controls.

PZM-0.12BS

Matsusada Precision

◆Level the product out to use for good heat dissipation.

Do not install the product upside down or sideways. If not, the inner heat dissipation will be

insufficient.

It may result in smoke or fire due to components deterioration.

◆Do not install the product in a place where cold air directly blows to it.

It may result in electric leakage or burnout due to condensation.

◆Do not install the product in a place where it is exposed to corrosive gases or liquids.

It may result in smoke or burnout due to components deterioration.

◆Do not install the product in a dusty place.

Accumulating dust in the air inlet will make hard to cool it down it, it may result in malfunction.

In that case, remove dust immediately.

◆Do not block the air inlet and outlet.

Secure 30 cm space at least around the openings.

If they are blocked, the product cannot show the rated performance due to the internal temperature

increase. Moreover, components deteriorate and it may result in smoke or fire.

◆Remove wirings to and from the product when work like welding near it are done.

◆Do not wipe the equipment with a dust cloth wet with chemicals (thinner or the like) or water.

Otherwise, it may result in an electric shock, electric leakage, or burnout due to water getting inside.

◆Regarding fan replacement

When products equip a fan, it has a lifetime. It will be worn out and deteriorated with the time

passed and its operation may become unstable. Also, its lifetime greatly varies depending on the

usage environment such as temperature, humidity, dust. It requires to be replaced at regular

intervals to extend the lifetime. For the replacement, contact us.

(It requires a replacement charge separately. Do not replace it by yourself, as there is a risk of

electric shock.)

PZM-0.12BS

Matsusada Precision

Table of Contents

Page

1. Introduction...........................................................................................................................................1

1-1 Greetings....................................................................................................................................1

1-2 Unpacking...................................................................................................................................1

1-3 Installation Conditions.................................................................................................................1

1-4 Handling Precautions..................................................................................................................2

1-5 Troubleshooting..........................................................................................................................2

2. External Appearance............................................................................................................................3

2-1 External Appearance ..................................................................................................................3

2-2 Control Connector Pin Assignment (15-pin, Female) ..................................................................4

3. Instruction for Handling.........................................................................................................................5

3-1 Overview.....................................................................................................................................5

3-2 Features .....................................................................................................................................5

3-3 Operation....................................................................................................................................6

1.Introduction

1PZM-0.12BS

Matsusada Precision

1-1 Greetings

Thank you very much for your purchase of Matsusada Precision piezo driver. This Instruction Manual

was written to provide the user with instructions on the safe operation of our piezo driver. Matsusada

Precision takes every precaution to ensure the quality of our products. Please refer carefully to this

manual in order to use this product correctly and safely, and to achieve the best possible performance.

We have made every effort to provide all of the necessary information in this manual. However, please

do not hesitate to contact us if you find any errors or omissions.

1-2 Unpacking

After unpacking the product and checking the power supply, make sure all of the following accessories

are included.

・Instruction manual (1)

・Output cable (1)

・Sensor cable (1)

1-3 Installation Conditions

・The piezo driver should be installed horizontally.

・Do not put anything on the piezo driver.

・The piezo driver has cooling air intake and exhaust ports on the top and side, respectively.

Provide enough space around the piezo driver and use it in a good ventilation condition.

・Avoid using the piezo driver in a place exposed to dust or corrosive gases.

1. Introduction

When the piezo driver is purchased separately

1.Introduction

2PZM-0.12BS

Matsusada Precision

1-4 Handling Precautions

・Be sure to connect the case of the product to the earth.

・The case earth and load earth should be short and connected with a thick wire so that it becomes

a single earth ground.

・Be careful not to touch the load immediately after the output is turned off.

1-5 Troubleshooting

In case of no output voltage,

1. Check whether the specified voltage is input.

・Power supply voltage: 12 to 15Vdc

・External input voltage: 0 to 10V

Tabla de contenidos

Otros manuales de Fuente de alimentación de Matsusada Precision

Matsusada Precision

Matsusada Precision R4GN Series Guía de instalación

Matsusada Precision

Matsusada Precision XR Series Manual de usuario

Matsusada Precision

Matsusada Precision CD Series Guía de instalación

Matsusada Precision

Matsusada Precision EJC Series Manual de usuario

Matsusada Precision

Matsusada Precision REK Series Manual de usuario

Matsusada Precision

Matsusada Precision DRS Series Guía de instalación

Matsusada Precision

Matsusada Precision R4G Series Manual de usuario

Matsusada Precision

Matsusada Precision PRT Series Manual de usuario

Matsusada Precision

Matsusada Precision EQ Series Manual de usuario

Matsusada Precision

Matsusada Precision EGD Series Guía de instalación

Matsusada Precision

Matsusada Precision EPR Series Manual de usuario

Matsusada Precision

Matsusada Precision RK-80 Series Manual de usuario

Matsusada Precision

Matsusada Precision R4G Series Manual de usuario

Matsusada Precision

Matsusada Precision AMP Series Manual de usuario

Matsusada Precision

Matsusada Precision PZJ Series Manual de usuario

Matsusada Precision

Matsusada Precision CO Series Manual de usuario

Matsusada Precision

Matsusada Precision AMPS Series Manual de usuario

Matsusada Precision

Matsusada Precision PSS2en-DCPS Manual de usuario

Matsusada Precision

Matsusada Precision AK Series Manual de usuario

Matsusada Precision

Matsusada Precision VOL Series Manual de usuario

Matsusada Precision

Matsusada Precision RKT Series Manual de usuario

Matsusada Precision

Matsusada Precision VOL Series Manual de usuario

Matsusada Precision

Matsusada Precision EGS Series Guía de instalación

Matsusada Precision

Matsusada Precision DOKF Series Manual de usuario

Manuales populares de Fuente de alimentación de otras marcas

Monacor

Monacor PS-12CCD Manual de usuario

VOLTIMA

VOLTIMA MagicBox 15 Manual de usuario

Agilent Technologies

Agilent Technologies 6032A Manual de usuario

Miller

Miller Auto Deltaweld 452 Manual de usuario

BCP

BCP PUOUBK Hoja de instrucciones

HC 2210 Manual de usuario

Puls

Puls CT5.241 Manual de usuario

OCZ

OCZ ZX1250W Manual de usuario

iseg

iseg ECH 238 Manual de usuario

Power

Power XXL A Series Manual de usuario

Agilent Technologies

Agilent Technologies 6631B Manual de usuario

Renogy

Renogy PHOENIX 300 Manual de usuario

HP 6200B Manual de servicio

Epson

Epson Stylus Scan 2500 Manual de funcionamiento

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Manual de usuario

Puls

Puls MiniLine ML50.100 Manual de usuario

Puls

Puls AS-Interface SLA4.100 Manual de usuario

Kenwood

Kenwood PS-60 Manual de usuario