Matsing MS-48C90 Manual de usuario

TABLE OF CONTENTS:

BEAMS & CONNECTORS:

Plan View Resultant Beam Direction

Beam 1-12 (Top Row 1) and Beam 25-36 (Third Row 3)

Beam 13-24 (Second Row 2) and Beam 37-48 (Bottom Row 4)

Rear View Connector Layout

Connector Port Table (From Rear View)

BEAM PATTERN

Horizontal Beam Pattern (Row 1 & 3)

Horizontal Beam Pattern (Row 2 & 4)

Vertical Beam Pattern

TRANSPORTATION / INSTALLATION

Transportation (From Point to Point)

Bracket Mounting

Installation using a crane

Lifting the Antenna

Antenna Installation

Antenna Leveling

Digital Level Gauge Calibration

Adjustment Requirement

Revision History:

[email protected] www.matsing.com 1 / 8

2.10

2.20

2.30

email:

website:

Page

Rev nos

3.41

3.42

3.43

Date

Description

Revised by

3.00

3.10

3.20

3.30

3.31

3.40

1.20

1.30

2.00

1.00

1.10

1.11

1.12

Pavel

MS-48C90-IM-001

INSTRUCTION MANUAL MS-48C90

MS-48C90

Instruction Manual

Date

Prepared by

Approved by

Document nos

Revision

21 Jun 2023

Ray Ling

BEAMS & CONNECTORS:

Plan View Resultant Beam Direction

Beam 1-12 (Top Row 1) and Beam 25-36 (Third Row 3)

Beam 13-24 (Second Row 2) and Beam 37-48 (Bottom Row 4)

2 / 8

Page

1.00

1.10

1.11

1.12

Frequency: 37MHz

Plan View Resultant Beam Directions

BEAM 25 - 36

(Third Row 3)

BEAM 1 - 12

(Top Row 1)



Frequency: 37MHz

Plan View Resultant Beam Directions

BEAM 37 - 48

(Bottom Row 4)

BEAM 13 - 24

(Second Row 2)

Rear View Connector Layout

3 / 8

1.20

Page

SYMBOLS:

P__=Port numbers





= (- 



Connector Port Table (From Rear View)

Beam 37-48

Beam 25-36

Beam 13-24

Beam 1-12

4 / 8

Page



PORT



PORT

BEAM



1.34

PORT





PORT



PORT



PORT

BEAM

1.33

BEAM



PORT



PORT

BEAM



1.32

PORT





PORT



PORT



PORT

BEAM

1.30

1.31

BEAM

BEAM PATTERN

Horizontal Beam Pattern (Row 1 & 3)

Horizontal Beam Pattern (Row 2 & 4)

Vertical Beam Pattern

5 / 8

2.30

2.20

2.00

2.10

TRANSPORTATION / INSTALLATION

Transportation (From Point to Point)

Bracket Mounting

6 / 8

Bolt & Nuts Sets

30cm to 120cm

Ø13mm x 8

M12 x 15cm=8sets

3.10

Strictly comply to the Local authority and regulatory on Workplace Safety and Health Control and

Measure when moving and transportation of large or heavy equipment, appropriate material

handling machine should be use.

(Risk Assessment apply for Forklift or Pallet Truck Lifting)

3.20

Item

Lens/Types

Holes Size

Bracket Qty

Page

3.00

ONE end bolt sets

Attached the bracket

tighten with

specified bolts sets.

Important Notes:

End User is require

Custom-Make

the additional

supporting bracket

and tighten to the

existing Antenna

bracket to meet the

deployment needs.

Installation using a crane

Lifting the Antenna

7 / 8

3.30

Page

Strictly comply to the local authority and regulatory on Workplace Safety and Health Control and

Measure when performing lifting of large or heavy equipment, appropriate material handling

machine should be used and only certified personnel should perform the task.

(Risk Assessment requirement applies for both Up-Lifting and Down-Lifting.)

3.31

The antenna has 2 hook points installed on the top frame (located slightly behind the center of the

sphere). These hooks are designed at the center of gravity point of the antenna. A cable, rope can be

securely fastened to the hooks and the antenna can be lifted using a crane as pictured below.

Antenna Installation

Antenna Leveling

Digital Level Gauge Calibration

Adjustment Requirement

8 / 8

Page

3.40

With reference to "Bracket Mounting Procedure", End user is required to Custom-Make the

additional supporting bracket and tighten it to the existing Antenna bracket to meet the deployment

needs.

3.41

After the Antenna is mounted to the bracket, it is required to be adjusted to 0˚ (Zero Degree) with

≤0.2˚ on 3 sides of the frame top level.(Rear, Right & Left=As shown in picture)

3.42

3.43

Tabla de contenidos

Otros manuales de Equipos industriales de Matsing

Matsing

Matsing MS-MBA-3.3.2-C2-H2-L2-I Manual de usuario

Matsing

Matsing MS12C90 Manual de usuario

Matsing

Matsing MS-MBA-3.2-H4-L4 Manual de usuario

Matsing

Matsing MS-MBA-3-C4A3 Manual de usuario

Matsing

Matsing MS-MBA-3-F4A3 Manual de usuario

Matsing

Matsing MS-MBA-3.3-C4A3-H4A2 Manual de usuario

Matsing

Matsing MS-24C180 Manual de usuario

Matsing

Matsing MS-8F60 Manual de usuario

Matsing

Matsing MS-MBA-3.3.2-F2-H2-L2 Manual de usuario

Matsing

Matsing MS-LP-6-H4-30i Manual de usuario

Matsing

Matsing MS-6C45 Manual de usuario

Matsing

Matsing MS-16F60 Manual de usuario

Matsing

Matsing MS-MBA-7-C2 Manual de usuario

Matsing

Matsing MS-6H90 Manual de usuario

Matsing

Matsing MS-24C180-I Manual de usuario

Matsing

Matsing MS-12C45 Manual de usuario

Matsing

Matsing MS-6F45 Manual de usuario

Matsing

Matsing MS-MBA-4.4-SH2-SH2-45 Manual de usuario

Matsing

Matsing MS-48F90 Manual de usuario

Matsing

Matsing MS-MBA-3-H8A2 Manual de usuario

Matsing

Matsing MS-8H120 Manual de usuario

Matsing

Matsing MS-MBA-4.4-SH2-SH2 Manual de usuario

Manuales populares de Equipos industriales de otras marcas

ABB

ABB Unifix AD Manual

Mark 7

Mark 7 Evolution Manual de usuario

Husky

Husky HyPET Manual de usuario

bora

bora PM-1800 Manual de usuario

Grizzly

Grizzly T32428 Manual de usuario

Siemens

Siemens 8MF1 Series Manual de usuario

ABB

ABB HT610965 Manual de usuario

ABB

ABB SafeLink Manual de usuario

Phoenix

Phoenix PHX-150 Manual de usuario

ABB

ABB A165-L32 Manual de usuario

ABB

ABB HT842936 Manual de usuario

Rioned

Rioned UrbanJet Manual de usuario

Hermetica

Hermetica 10 Series Manual de usuario

HORNER

HORNER OEE Solution Manual de usuario

Hammerhead

Hammerhead HG375 Manual de usuario

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instrucciones de uso

ABB

ABB HT566657 Manual de usuario

Webasto

Webasto GSE CAN Manual de usuario