Matrix Visionpro Manual de usuario
VISIONPRO
Quick Start
VISIONPRO
The Digital PBX for Small Offices
Quick Start
Documentation Disclaimer
Matrix Comsec reserves the right to change, at any time, without prior notice, the product design,
specifications, components, as engineering and manufacturing may warrant.
This is a general documentation for all models/configurations of the product. The product may not
support some of the features/facilities described in this document.
While every reasonable effort has been made to ensure accuracy of content in this document,
Matrix Comsec assumes no responsibility for errors or omissions that may occur herein. No
liability is assumed for damages, costs, expenses resulting from unauthorized modifications or
repairs to the product; failure to use information or to comply with the installation, operation and
maintenance instructions contained in this document.
Copyright
All rights reserved. No part of this document may be copied or reproduced in any form or by any
means without the prior written consent of Matrix Comsec.
Version V1
Release date: October 4, 2019
Table of Contents i
Contents
Know Your VISIONPRO ................................................................................. 1
Overview ........................................................................................................... 1
Installing VISIONPRO .................................................................................... 3
Preparing for Installation ................................................................................... 3
Getting Started .................................................................................................. 3
Connecting VISIONPRO .................................................................................. 4
Power On VISIONPRO ..................................................................................... 6
Configuring VISIONPRO ................................................................................ 9
Test Calls ........................................................................................................ 14
Matrix VISIONPRO Quick Start 1
Know Your VISIONPRO
Thank you for choosing the Matrix VISIONPRO. Please read the instructions in this Quick Start
carefully to install and configure it.
This Quick Start is meant to help you install and configure the VISIONPRO quickly. For detailed
instructions on configuring the product and its feature description, refer to the System Manual.
To view or download the documents, scan the QR Code printed on the Product Label/Packaging
Label. You can also view or download the documentation from https://www.matrixtelesol.com/
product-manuals.html
For product registration and warranty related details, please visit http://www.matrixcomsec.com/
product-registration-form.html
Overview
Matrix VISIONPRO is an integrated digital SOHO (Small Office Home Office) PBX which caters to
the communication requirements of small businesses.
VISIONPRO series from Matrix offers the following variants,
• VISIONPRO 206 with 2 CO Trunk Ports (FXO Ports) and 6 SLT Ports (FXS Ports).
• VISIONPRO 308 with 3 CO Trunk Ports (FXO Ports) and 8 SLT Ports (FXS Ports).
• VISIONPRO 412 with 4 CO Trunk Ports (FXO Ports) and 12 SLT Ports (FXS Ports).
2 Matrix VISIONPRO Quick Start
This Quick Start is written with reference to the default configuration, VISIONPRO 308, unless
otherwise specified.
Ports and Connectors
LED
Port Description
Power Port To connect the external power adapter of 12V DC (input).
Earth To connect the telecom earth to the system.
CO To connect the CO trunk lines from PSTN.
SLT To connect station SLT phones, FAX machines.
RESET To reset the SE/SA Password to its default value.
LED Description
PWR To indicate system power ON/OFF condition.
STS To indicate the system status during various conditions.
Matrix VISIONPRO Quick Start 3
Installing VISIONPRO
Preparing for Installation
You must have the following:
• A suitable location to install VISIONPRO.
• Necessary telecom wiring in place, with wall jacks for station lines at the required locations.
• Standard, good quality, twisted pair telephone cables with 0.5 mm conductor diameter.
• A dedicated Power supply outlet close to the system.
• As many standard analog telephone instruments with CLI display to connect as SLT stations.
• A fax machine, if you want to connect one to the SLT Port of VISIONPRO.
• One or more active, analog trunk lines from the CO network, as required.
Well begun is half done; plan your hardware installation well.
• Do not install this product near an area where-
• it is exposed to direct sunlight, heat, excessive cold or humidity, dust, oil, corrosive
fumes.
• there is a water source (wash basin, tub, shower, pool, sprinkler etc.)
• there is source of electromagnetic noise such as radio equipment, heavy transformers,
faulty electric chokes of tube-lights, device having a faulty coil.
• Ensure proper electrical earth and telecom earth for the safety of the product and persons
handling it.
Getting Started
Unpack VISIONPRO and verify your package contents. In case any of the items is missing or
damaged, contact your Dealer/Distributor.
4 Matrix VISIONPRO Quick Start
Package Contents
The ideal sales package for VISIONPRO should contain the following items:
• One VISIONPRO Unit
• A 12V Power Adapter
• A Wall Mounting Template
• Two Screw Grips
• Two M7/30 Screws
You can view or download the documentation of the product by scanning the QR code printed on
the Product Label/Packaging Label.
Connecting VISIONPRO
Matrix VISIONPRO Quick Start 5
To connect the CO cables to the VISIONPRO,
• Use standard, good quality, twisted-wire pair telephone cables to connect the CO Ports of
VISIONPRO to the Trunk Lines from the CO (central office) network.
• Strip off about half a centimeter of the insulation off the wire ends of the CO cable.
• Using a blunt pin or a small flat screw driver, push back the levers of the connector.
• Insert the stripped ends of the two wires into the two openings of the connector, with one wire
in each opening.
• Ensure that both wires fit neatly into the opening.
• Release pressure on the levers. Both wires will be held in place by spring clamp action.
If you need to remove the wires,
• Push back the levers.
• Pull out the wires gently.
• Release pressure on the levers.
To connect the SLT cables to the VISIONPRO,
• Use standard twisted wire pair cables of good quality to connect the analog single line
telephone instruments to the SLT Ports of VISIONPRO.
6 Matrix VISIONPRO Quick Start
• Place the SLTs, fax machine at the desired locations. Connect the SLTs, Fax machine to the
wall jacks.
• Terminate one end of the cable on the wall jack to which the SLT, fax machine is connected.
• From the other end of the wire, strip off about half a centimeter of the insulation.
• Using a blunt pin or a small flat screw driver, push back the levers of the connector.
• Insert the stripped ends of the two wires into the two openings of the connector, with one wire
in each opening.
• Ensure that both wires fit neatly into the opening.
• Release pressure on the levers. Both wires will be held in place by spring clamp action.
If you need to remove the wires,
• Push back the levers.
• Pull out the wires gently.
• Release pressure on the levers.
Power On VISIONPRO
• Check the mains voltage at the power plug from where the power supply is to be fed to the
system.
• Make sure system’s earthing is proper.
• Plug in the power adapter of VISIONPRO into the power outlet. Ensure proper contacts.
Switch ON the system. Observe the reset cycle on the front panel of the system.
Reset Cycle
• As soon as you power ON the system, the PWR (Power) LED on the front panel starts
glowing. The STS (Status) LED starts glowing approximately 5 seconds after power ON.
Thereafter, the STS LED blinks in a cadence of 1sec ON and 1sec OFF.
• The system also feeds Dial Tone to the stations.
• Check for Dial Tone on the telephone instruments connected to the system.
Otros manuales para Visionpro
1
Tabla de contenidos
Otros manuales de Centralita privada de Matrix
Matrix
Matrix Visionpro Guía del usuario
Matrix
Matrix ETERNITY NE Manual de usuario
Matrix
Matrix ETERNITY Manual de usuario
Matrix
Matrix Vision Guía del usuario
Matrix
Matrix ETERNITY Manual de lista de piezas
Matrix
Matrix ETERNITY NE Manual de usuario
Matrix
Matrix ETERNITY ME Manual de usuario
Matrix
Matrix ETERNITY NE Manual de usuario
Matrix
Matrix PROTON 103 Manual de usuario
Matrix
Matrix ETERNITY NE Guía del usuario
Manuales populares de Centralita privada de otras marcas
Allo.com
Allo.com Nano 2 Manual de usuario
ZYCOD
ZYCOD ZX50 Manual de usuario
Panasonic
Panasonic KX-TDA100BX Manual de usuario
LV switch
LV switch IPPBX800 Manual de instrucciones
Edge-Core
Edge-Core VST3305 Manual de usuario
Panasonic
Panasonic KX-T7625 - Digital Proprietary Speakerphone 24... Manual de usuario
Rauland-Borg
Rauland-Borg Telecenter IV Manual de usuario
Grandstream Networks
Grandstream Networks UCM6208 Manual de usuario
ATCOM
ATCOM IPPBX IP02 Manual de usuario
Panasonic
Panasonic KX-TVS50 - 2 Port Voicemail System Manual de usuario
bintec elmeg
bintec elmeg elmeg hybird 600 Manual de usuario
Panasonic
Panasonic KX-NS300 Manual de usuario
