Masterlock BCO0103 Guía

Instructions for installation of knob or lever locksets

Backset is the distance from the door edge to the center of the hole on the door face. Master Lock door locks are supplied

with an adjustable latch which can fit 2-3/8” (60mm) or 2-3/4” (70mm) backset.

Follow steps below to change backset.

To convert to 2-3/4" backset

Backset

a. This latch is for 2-3/8" (60mm) backset.

b.Keep spindle cam in correct position as illustrated. Pull spindle cam all the way to the right.

c. Your latch is now set for 2-3/4" (70mm) backset.To reset 2-3/8" backset,push spindle all the way back to the left.

Mark door with template Drill holes

Measure one half of door thickness from doorstop

and mark for the vertical centerline of strike. Drill

1" hole, 1/2" deep at the intersection of the

horizontal and vertical centerlines.

Close door to mark horizontal

centerline of strike.

Insert latch in

hole, mark

outline of face

plate and

chisel 11/64"

(4mm) deep.

Insert latch and tighten screws.

Select 2-3/8" or 2-3/4" (60mm or 70mm)

backset as desired and mark center of hole

on door face.

Drill 2-1/8" (54mm) hole on door face from both sides

to avoid wood splitting. Drill 1" (25.4mm) hole for latch.

Install latch

Attach the latch face that matches the mortise in the edge of your door

Fin

Floating Sleeve

Round Face Plate

Locate floating sleeve and round

face plate and proceed.

To change latch faces:

1. Use a flat screwdriver to separate the face plate.

2. Snap selected latch face onto backplate.

For drive in installation:

Push latchbolt to the end and hold. Align the round face

plate opening with the fin on the latch. Push to the end

and rotate the round face plate counter-clockwise. After

assembly, release latchbolt to fully extend. Move the

floating sleeve toward the round face plate until the

edge fits into the ring opening of the round face plate.

Back Plate

Face Plate

Install outside knob (or lever)

Insert spindle through latch. Press flush against door. (NOTE: Key hole must be in down position).

Install inside knob (or lever)

Install inside knob (or lever) and tighten screws until lock is firm.

a. Match screw holes on strike with vertical centerlines on jamb. Mark outline of strike plate and chisel out until strike

is flush with jamb. (Approx. 1/8")

b.Install strike and tighten screws.

Install strike

1-3/4"

45mm 1-9/16"

40mm 1-3/8"

35mm

Make 1" Hole at Center of Door Edge

TEMPLATE

Fold on Dotted Line and Fit on Door Edge

For Backset 2-3/8"

For Backset 2-3/4"

Check out the collection of home doors & windows we offer.

Este manual sirve para los siguientes modelos

Otros manuales de Cerrar de Masterlock

Masterlock

Masterlock 1630 Manual de servicio

Masterlock

Masterlock SAFESPACE 5423D Manual de usuario

Masterlock

Masterlock 1630 Manual de usuario

Masterlock

Masterlock 4696 Manual de usuario

Masterlock

Masterlock 3685 Manual de usuario

Masterlock

Masterlock Select Access 5426EURD Manual de usuario

Masterlock

Masterlock master lock Manual de usuario

Masterlock

Masterlock eONE Manual de usuario

Masterlock

Masterlock 6400 Manual de usuario

Masterlock

Masterlock Speed Dial 1500iD Manual de usuario

Masterlock

Masterlock 3630 Manual de usuario

Masterlock

Masterlock Select Access 5426EURD Manual de instrucciones

Masterlock

Masterlock 4696DWD Manual de usuario

Masterlock

Masterlock 4697D Manual de usuario

Masterlock

Masterlock 4697 Manual de usuario

Masterlock

Masterlock Pushkey 2650EURD Manual de usuario

Masterlock

Masterlock 4696D Manual de usuario

Masterlock

Masterlock Select Access 5412EURD Manual de usuario

Masterlock

Masterlock 651EURD Manual de usuario

Masterlock

Masterlock 5400D Manual de usuario

Masterlock

Masterlock 5424EURD Manual de usuario

Masterlock

Masterlock 3685 Manual de usuario

Masterlock

Masterlock M175 Manual de usuario

Masterlock

Masterlock 5441EURENT Manual de usuario

Manuales populares de Cerrar de otras marcas

Magic

Magic 105 Manual de usuario

Gantner

Gantner GAT NET.Lock 7020 System Guía rápida

Wittkopp

Wittkopp Insys 7202 Manual de usuario

Dorma

Dorma Studio Classic Manual de usuario

Securam

Securam ECSL-601 Manual de usuario

Sudhaus

Sudhaus 3003 Manual de usuario

Safety 1st

Safety 1st 48517 Manual de usuario

Pado

Pado FDS-10 Manual de usuario

Esco

Esco systeQ Series Manual de usuario

COMPX

COMPX National D8951 Manual de usuario

secureo

secureo Key Box Manual de usuario

Stock Loks

Stock Loks C8713 Manual de usuario

COMPX

COMPX 1T-058 Manual del propietario

Auslock

Auslock T11 Manual de usuario

ELCOM

ELCOM 7205 Manual de usuario

Stealth SAFES

Stealth SAFES ShadowVault Manual de usuario

Knox

Knox KeySecure 5 Manual de usuario

Kwikset

Kwikset 48334/01 Manual de usuario