MasterForce 241-0738 Manual de usuario
Owner’s Manual
Hammer Drill
241-0738
IMPORTANT:
Read through this Owner’s Manual carefully before using this tool. Pay
close attention to all Safety Instructions, Warnings, and Cautions. Use this
tool properly, and only for its intended use.
Safety symbols in this Manual are used to flag possible dangers. The safe-
ty symbols and their explanations require your full understanding. The safety
warnings do not eliminate any danger by themselves, and they are not a sub-
stitute for proper accident prevention measures.
This Safety Alert Symbol indicates caution, warning, or danger. Failure to
obey a safety warning can result in serious injury to yourself or others. To reduce
the risk of injury, fire, or electric shock, always follow the safety precautions.
2
TABLE OF CONTENTS
Specifications…………..…………………………………………... Page 2
Rules for Safe Operation……………..……………………………... Page 3
Know the Hammer Drill…………………………………………….. Page 7
Assembly and Adjustments………………………………………..... Page 9
Operating Instructions…..………………………………………....... Page 10
Maintenance……………………………………………………........Page 12
Trouble Shooting…..……………………………………………........ Page 13
Warranty……………..…………………………………………........ Page 14
SPECIFICATIONS
Model: 241-0738
Motor: 120 V, 60 Hz, 7.5 A
Keyed chuck: 1/2” (13 mm)
Variable speed ranges: 0–1080 & 0–3000 RPM
Hammer: 0–18,000 & 0–48,000 BPM
Maximum drilling capacity: 1/2” in steel
1/2” in Concrete (3/16”-3/8” Optimum)
1 1/4” in Wood
Weight: 7 lb 8 oz (3.4 kg)
SAFETY SYMBOLS FOR YOUR TOOL
The label on your tool may include the following symbols
V ..............................................................Volts
A ..............................................................Amps
Hz ............................................................Hertz
W .............................................................Watts
min ..........................................................minutes
..........................................................Alternating current
.........................................................Direct current
no ..............................................................No load speed
...........................................................Class II construction,Double insulated
.../min .....................................................Revolutions or Strokes per minute
...........................................................Indicates danger,warning or caution.
It means attention!Your safety is involved
..........................................................Wet Conditions Alert! Do not expose to
rain or use in damp locations
3
RULES FOR SAFE OPERATION
KNOW THE TOOL
To operate this tool, carefully read this Owner’s Manual and all labels affixed
to the hammer drill before using it. Keep this Manual for future reference.
IMPORTANT
This tool should only be serviced by a qualified service technician. For more
information, call the toll-free helpline, at 1-866-917-4374.
READ ALL INSTRUCTIONS THOROUGHLY
GENERAL SAFETY PRECAUTIONS
WARNING: Read and understand all instructions. Failure to follow all in-
structions listed below may result in electric shock, fire and/or serious per-
sonal injury.
SAVE THESE INSTRUCTIONS.
WORK AREA
• Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
• Keep bystanders, children, and visitors away while operating a power
tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
• Double insulated tools are equipped with a
polarized plug (one blade is wider than the other).
This plug will fit in a polarized outlet only one
way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a
qualified electrician to install a polarized outlet.
Do not change the plug in any way. Double
insulation eliminates the need for the three
wire grounded power cord and grounded power
supply system.
120V ~ 60Hz
Fig. 1
4
• Avoid body contact with grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if
your body is grounded.
• Don’t expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord to carry the tool or to pull
the plug from an outlet. Keep the cord away from heat, oil, sharp edges
or moving parts. Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
• When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These cords are rated for outdoor use and reduce
the risk of electric shock.
Personal Safety
• Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use the tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair.
Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
• Avoid accidental starting. Be sure that the switch is off before plugging in
the tool. Carrying tools with your finger on the switch or plugging in tools
that have the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench
or a key that is left attached to a rotating part of the tool may result in
personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enable better control of the tool in unexpected
situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid
safety shoes, hard hat, or hearing protection must be used for appropriate
conditions.
• Before connecting the tool to a power source (receptacle, outlet, etc.),
be sure that the voltage supplied is the same as that specified on the
nameplate of the tool. A power source with voltage greater than that
specified for the tool can result in serious injury to the user – as well as
damage to the tool.
5
Tool Use and Care
• Use clamps or another practical way to support and secure the workpiece
to a stable platform. Holding the work by hand or against your body is
unstable and may lead to loss of control.
• Do not force the tool. Use the correct tool for your application. The
correct tool will do the job better and more safely at the rate for which is
designed.
• Do not use the tool if the switch does not turn it on or off. Any tool that
cannot be controlled with the switch is dangerous and must be repaired.
• Disconnectthe plugfrom thepower sourcebefore makingany adjustments,
changing accessories, or storing the tool. Such preventive safety measures
reduce the risk of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly
maintained tools with sharp cutting edges are less likely to bind and are
easier to control.
• Check for misalignment or binding of moving parts, breakage of parts,
and any other condition that may affect the tool’s operation. If damaged,
have the tool serviced before using. Many accidents are caused by poorly
maintained tools.
• Use only accessories that are recommended by the manufacturer for
your model. Accessories that may be suitable for one tool may become
hazardous when used on another tool.
• Do not alter or misuse tool. This tool is precision built. Any alteration
or modification not specified is misuse and may result in a dangerous
condition.
Service
• Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk
of injury.
• When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance section of this manual. Use of unauthorized
parts or failure to follow Maintenance instructions may create a risk of
electric shock or injury.
6
SPECIFIC SAFETY RULES FOR THE HAMMER DRILL
• Hold the tool by its insulated gripping surfaces when performing any
operation where the tool may come into contact with hidden wiring or
its own cord. Contact with a “live” wire will make exposed metal parts of
the tool “live” and shock the operator.
• Only use accessories that are in good condition.
• Check that there is sufficient clearance for the drill bit under the
workpiece before drilling,
• Before plugging the tool in, check that the trigger lock-on button is “OFF”.
• When starting the hammer drill, let the drill run for a few seconds before
using it on a workpiece. Watch for vibration or wobbling that could
indicate poor installation of an accessory.
• Always use the auxiliary handle that is included with the tool. Loss of
control can cause personal injury.
• If possible, always use clamps or a vise to hold the work.
• Always switch the drill OFF before putting it down.
• Ensure that the lighting is adequate to see the operation.
• Do not put pressure on the drill to the extent that it slows down the motor.
For better results, and to lengthen the life of the drill, allow the drill bit to
cut without pressure.
• Keep the work area free of tripping hazards.
• Secure the material that is being drilled. Never hold it in your hand or
across your hand or across your legs.
• Do not use damaged or bowed drill bits.
• Keep hands away from rotating parts.
• Always wear safety goggles and a dust mask when drilling, especially
when drilling above the level of your head.
• Watch out for flying sparks. Hold the tool so that any sparks will fly away
from the operator and other persons. Keep all flammable materials away
when using this drill.
• Do not touch the workpiece immediately after operation. It may be
extremely hot, and could burn the skin.
• If an extension cord is required, use a cord with adequate size
conductors in order to prevent excessive voltage drop, loss of power, or
overheating. The table on the next page shows the correct size to use,
depending on cord length and nameplate amperage rating of tool. When
in doubt, use the next heavier gauge. Always use UL and CSA listed
extension cords.
7
KNOW THE HAMMER DRILL (See Fig. 2)
Before attempting to use this hammer drill, become familiar with all of its
operating features and safety requirements.
WARNING: Do not allow familiarity with the hammer drill to cause care-
lessness. Remember that a fraction of a second of carelessness is enough to
inflict severe injury.
1. Hammer drill/drill switch
2. Trigger switch
3. Lock-on button
4. Forward/reverse switch
5. Chuck key
6. Auxiliary handle
7. Chuck
8. Depth gauge
9. Mechanical speed-adjustment
knob
INSTALLING AND REMOVING
DRILL BITS (Fig. 3)
To install:
WARNING! Do not attempt to
tighten the chuck by gripping the
front part and turning the drill on.
Damage to the tool and personal in-
jury may result. Be sure to tighten the
chuck with the chuck key.
Fig. 2 1
94
62
3
5
7
8
Fig. 3
Tool’s Ampere rating Volts
Total length of cord in feet
Cord size in A. W. G.(minimum)
25’ 50’ 100’ 150’
0-6
120
V~
18 16 16 14
6-10 18 16 14 12
10-12 16 16 14 12
12-16 14 12 Not Recommended
8
1. To open the chuck jaws, insert the chuck key into one of the three holes
located on the chuck. Turn the key counter-clockwise.
2. Insert the bit into the chuck jaws. Center the bit in the chuck jaws.
3. To close the chuck jaws, insert the chuck key into one of the three holes
in the chuck. Turn the chuck key clockwise until the chuck is tightened
securely.
To remove:
1. Insert the chuck key into one of the holes in the chuck.
2. Turn the chuck key counter-clockwise to loosen the chuck.
3. Remove the bit.
WARNING! The bit can become very hot during use. Wear gloves or wait
for the bit to cool before removing the bit.
INSTALLING THE AUXILIARY
HANDLE (Fig. 4)
Loosen the auxiliary handle by
turning it counter-clockwise. Rotate
the handle to any position, and then
tighten the handle.
INSTALLING THE DEPTH
GAUGE (Fig. 5)
Loosen the knob, adjust the depth
gauge to the desired position, and
then tighten the knob.
Fig. 5
Knob
Fig. 4
9
ASSEMBLY AND ADJUSTMENTS
MECHANICAL SPEED-ADJUSTMENT KNOB (Fig. 6)
Adjust the mechanical variable-
speed knob in either direction. The
speed ranges for the two directions
are as follows:
On setting “I”, the speed range is
0-1080 RPM and 0-18000 BPM.
On setting “II”, the speed range is
0-3000 RPM and 0-48000 BPM.
NOTE: After adjusting the
mechanical speed-adjustment knob,
depress the trigger switch to start
the drill, gradually increasing speed to allow the tool to run freely.
HAMMER DRILL/ DRILL SWITCH (Fig .7)
Set to (“drill”) to drill holes in wood, metal, or soft masonry.
Set to (“hammer drill”) to drill
holes in concrete or hard masonry.
FORWARD/REVERSE SWITCH.
(Fig. 8)
The forward/reverse switch
determines the running direction of
the tool.
1. To select “forward” motion,
release the trigger switch, and
push the forward/reverse switch
to the right side of the tool.
2. To select “reverse” motion,
release the trigger switch, and
push the forward/reverse switch
to the left side of the tool.
NOTE: When operating the tool in
“reverse” rotation, the trigger switch
can be depressed only halfway and
the tool runs at half speed. The lock-
on button cannot be activated in
“reverse.”
Fig. 7
Fig. 8
Reverse
Forward
Fig. 6
10
ON/OFF SWITCH AND LOCK-ON BUTTON (Fig. 9)
To start the drill:
1. To turn the tool “ON”, depress the
trigger switch (1). Increase the
pressure on the trigger switch to
increase the speed.
2. To turn the tool “OFF”, release the
trigger switch (1).
CAUTION! Allow the motor to
come to a complete stop before set-
ting the drill down.
Lock on for continuous operation:
The trigger switch is equipped with a lock-on button.
1. To activate the lock-on feature, squeeze the trigger switch (1) to turn the
tool “ON”, and then depress the lock-on button (2). The trigger switch is
locked “ON”.
2. To disable the lock-on button and turn the tool OFF, squeeze the trigger
switch (1) again. The lock-on button will disengage. Release the trigger
switch to turn the tool “OFF”.
OPERATING INSTRUCTIONS
DRILLING OPERATION
Hold the drill comfortably, with your finger on the trigger switch.
Use the auxiliary handle whenever possible to gain extra control and to
prevent fatigue.
NOTE:
• Use sharp drill bits only.
• For wood, use twist-drill bits, spade bits, power-auger bits, or hole saws.
• For metal, use high-speed, steel-twist drill bits or hole saws.
• For masonry (brick, cement, cinder block, etc.) use carbide-tipped drill
bits.
• Be sure that the material to be drilled is anchored or clamped firmly.
• If drilling thin material, use a “back-up” block to prevent damage to the
material.
Fig. 9
1
2
Tabla de contenidos
Otros manuales de Perforar de MasterForce
MasterForce
MasterForce 241-0301 Manual de usuario
MasterForce
MasterForce 241-0315 Manual de usuario
MasterForce
MasterForce Flexpower 241-0436 Manual de usuario
MasterForce
MasterForce 241-0409 Manual de usuario
MasterForce
MasterForce 241-0465 Manual de usuario
MasterForce
MasterForce 241-0725 Manual de usuario
MasterForce
MasterForce 241-0413 Manual de usuario
MasterForce
MasterForce 241-0381 Manual de usuario
MasterForce
MasterForce 241-0313 Manual de usuario
MasterForce
MasterForce 241-0405 Manual de usuario
