MasterCraft 058-8489-4 Manual de usuario

INSTRUCTION MANUAL

AIR-POWERED 3-IN-1 NAILER

058-8489-4

TABLE OF CONTENTS

AIR-POWERED 3-IN-1 NAILER 058-8489-4

QUICK START GUIDE

TECHNICAL SPECIFICATIONS 3

SAFETY GUIDELINES 4–9

KEY PARTS DIAGRAM 10

IMPORTANT INFORMATION 11–14

OPERATING INSTRUCTIONS 15–20

MAINTENANCE 21–22

TROUBLESHOOTING 23–25

EXPLODED VIEW 26

PARTS LIST 27–28

WARRANTY 29–30

SAFETY GUIDELINES

AIR-POWERED 3-IN-1 NAILER 058-8489-4

Safety guidelines

This manual contains information that relates to PROTECTING PERSONAL SAFETY and PREVENTING

EQUIPMENT PROBLEMS. It is very important to read this manual carefully and understand it

thoroughly before using the product. The symbols listed below are used to indicate this information.

Note- The word “Note” is used to inform the

reader of something he/she needs to know about

the tool.

PERSONAL SAFETY

These precautions are intended for the personal safety of the user and others working with the user.

Please take time to read and understand them.

DANGER!

Potential hazard that will result in serious

injury or loss of life.

WARNING!

Potential hazard that could result in

serious injury or loss of life.

CAUTION!

Potential hazard that may result in

moderate injury or damage to equipment.

SAFETY GUIDELINES

AIR-POWERED 3-IN-1 NAILER 058-8489-4

SAFETY GUIDELINES

Note: Carefully read and understand all the instructions in this manual before using the tool. Ensure

that the operator has read and understood these instructions.

DANGER!

Potential hazard that will result in serious injury or loss of life.

•Keep children away from the work area. Do not allow children to handle

power tools.

•Keep air hose away from heat, oil, and sharp edges. Check air hose for

wear before each use and ensure that all connections are proper.

•Always ensure that the workpiece is firmly secured leaving both hands free

to control the tool.

•Always ensure that the tool has stopped before putting it down after use, for

safety purposes and to prevent possible damage to the tool/user.

•Keep proper footing at all times in order to ensure correct balance.

•Do not use oxygen or any other combustible or bottled

gas to power air-powered tools. Failure to observe this

warning can cause explosion and serious personal injury

or death. Use only the compressed air to power the air-

powered tools. Use a minimum of 25' (7.6 m) of hose to

connect the tool to the compressor. Failure to comply will

result in serious injury or loss of life.

•Risk of electric shock: Do not expose a compressor to rain. Store it indoors.

Disconnect the compressor from power source before servicing. Compressor

must be grounded. Do not use grounding adaptors.

•Risk of personal injury: Do not direct compressed air from the air hose

towards the user or other personnel.

Oxygen

Hydrogen

Explosive

Combustible

MC-OM-02

SAFETY GUIDELINES

AIR-POWERED 3-IN-1 NAILER 058-8489-4

•Risk for breathing: Never directly inhale the air produced by the compressor.

•Risk of bursting: Do not adjust the pressure switch or safety valve for any

reason. They have been preset at the factory for this compressor’s maximum

pressure. Tampering with the pressure switch or the safety valve may cause

personal injury or property damage.

•Risk of burns: The pump and the manifold generate high temperatures. In

order to avoid burns or other injuries, do not touch the pump, the manifold,

or the transfer tube while the compressor is running. Allow the parts to cool

down before handling or servicing. Keep children away from the compressor

at all times.

•Risk of bursting: Make sure the regulator is adjusted so

that the compressor outlet pressure is set lower than the

maximum operating pressure of the tool. Before starting

the compressor, pull the ring on the safety valve to make

sure the valve moves freely. Drain water from tank after

each use. Do not weld or repair tank. Relieve all pressure

in the hose before removing or attaching accessories. MC-OM-22

SAFETY GUIDELINES

AIR-POWERED 3-IN-1 NAILER 058-8489-4

WARNING!

Potential hazard that could result in serious injury or loss of life.

•Do not allow unskilled or untrained individuals to operate the Air-powered

3-in-1 Nailer.

•Do not use the Air-powered 3-in-1 Nailer for any task other than that it is

designed to perform.

•Locate the compressor in a well-ventilated area for cooling, and a minimum

of 12" (31 cm) away from the nearest wall.

•Protect the air hose and the power cord from damage and puncture. Inspect

them for weak or worn spots every week and replace them if necessary.

•Always wear hearing protection when using the air compressor. Failure to do

so may result in hearing loss.

•Do not carry the compressor while it is running.

•Do not operate the compressor if it is not in a stable position.

•Do not operate the compressor on a rooftop or an elevated position that

could allow the unit to fall or be tipped over.

•Always replace a damaged gauge before operating the unit again.

SAFETY GUIDELINES

AIR-POWERED 3-IN-1 NAILER 058-8489-4

CAUTION!

Potential hazard that may result in moderate injury or damage to

equipment.

•Always ensure that the tool has stopped before connecting to the air supply.

•Do not wear watches, rings, bracelets, or loose clothing when using any air-

powered tool.

•Do not overload the tool. Allow the tool to operate at its optimum speed for

maximum efficiency.

• Do not use a tool that is leaking air, that has missing or damaged parts, or

that requires repairs. Verify that all screws are securely tightened.

• For optimal safety and tool performance, inspect the tool daily in order to

ensure free movement of the trigger, safety mechanisms, and springs.

•Always keep your air tool clean and lubricated. Daily lubrication is essential

to avoid internal corrosion and possible failures.

•Ensure the floor is not slippery and wear non-slip shoes. Floors should be

kept clean and clear.

•Always follow all workshop safety rules, regulations, and conditions when

using the Air-powered 3-in-1 Nailer.

•Carry the tool by the handle only, keeping fingers away from the trigger. Do

not carry the tool by the hose, magazine, or any other parts.

•Do not use the tool near or below freezing point, as doing so may cause tool

failure.

•Do not store the tool in a freezing environment to prevent ice formation on

the tool’s operating valves, as doing so may cause tool failure.

•Handling and storage of oil: Use with adequate ventilation. Avoid contact of

oil with eyes, skin, and clothing. Avoid breathing spray or mist. Store in a

tightly closed container in a cool, dry, well-ventilated area free from

incompatible substances.

SAFETY GUIDELINES

AIR-POWERED 3-IN-1 NAILER 058-8489-4

Note: Recycle unwanted materials rather than disposing of them as waste. Sort the tools, hoses, and

packaging in specific categories and take to the local recycling centre or dispose of in an

environmentally safe way.

CAUTION!

Potential hazard that may result in moderate injury or damage to

equipment.

•Disconnect tool from the air supply and turn off the

compressor before performing any maintenance or changing

accessories, when clearing a jammed fastener, when the

tool is not in use, when it is being handed to another

person, and when it is left unattended. Failure to comply

may result in moderate injury or damage to equipment.

•Use safety goggles and ear protection:

Wear safety glasses with side shields when operating the

tool/compressor and verify that others in the work area are

also wearing safety glasses. Safety glasses must conform to

American National Standards Institute (ANSI Z87.1)

requirements and must provide protection from flying

particles from the front and the sides.

Air-powered tools are loud and the sound can cause hearing

damage. Always wear ear protection to prevent hearing

damage and loss. Failure to comply may result in moderate

injury.

MC-OM-21

MC-OM-01

KEY PARTS DIAGRAM

AIR-POWERED 3-IN-1 NAILER 058-8489-4

No. Description No. Description

1 Air inlet plug 6 Safety tip

2 Trigger 7 Safety stand

3 Depth adjustment dial 8 Release latch

4 Magazine latch 9 Air deflector

5Magazine

MC-588489-01

Tabla de contenidos

Otros manuales de Pistola de clavos de MasterCraft

MasterCraft

MasterCraft Maximum 54-2963-8 Manual de usuario

MasterCraft

MasterCraft AIR-POWERED BRAD NAILERS Manual de usuario

MasterCraft

MasterCraft 058-8198-6 Manual de usuario

MasterCraft

MasterCraft 058-8122-6 Manual de usuario

MasterCraft

MasterCraft 058-9816-0 Manual de usuario

MasterCraft

MasterCraft AIR-POWERED 2-IN-1 NAILER Manual de usuario

MasterCraft

MasterCraft 058-8691-0 Manual de usuario

MasterCraft

MasterCraft 058-8691-0 Manual de usuario

MasterCraft

MasterCraft 058-8179-2 Manual de usuario

MasterCraft

MasterCraft Air-Powered Brad Nailer/Stapler Manual de usuario

MasterCraft

MasterCraft 058-8434-4 Manual de usuario

Manuales populares de Pistola de clavos de otras marcas

Performance Tool

Performance Tool M643 Manual de usuario

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco Fusion Technology F-35XP Manual de usuario

Grizzly

Grizzly G1847 Manual de usuario

Ryobi

Ryobi R18N18G Manual de usuario

Black & Decker

Black & Decker 492848-00 Manual de usuario

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manual de usuario

Metabo HPT

Metabo HPT NR 3690DC Manual de instrucciones

Surtek

Surtek CN650 Dimensiones y guía de instalación

Makita

Makita GF600 Manual de usuario

Parkside

Parkside PET 25 B1 Manual de usuario

Senco

Senco AirFree 25 Manual de usuario

Freeman

Freeman P50LSLW Manual de usuario

Aicon PRO

Aicon PRO DAC4507 Manual de usuario

DAJ

DAJ XR150A Manual de usuario

Makita

Makita AN923 Manual de usuario

Grizzly

Grizzly T20644 Manual de usuario