Master FTR80 Manual de usuario
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
1
OPERATION MANUAL
FTR80 Tamping Rammer
P E R F O R M A N C E · E F F I C I E N T · R E L I A B L E
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
2
Master sincerely thanks you for selecting the Plate
Compactor Machine. For your Safety and proper operation,
before you start to operate or carry out any maintenance on
this equipment, YOU MUST READ and STUDY this manual
carefully. Be sure to always keep it ready for reference.
Produced By Henan Master Machinery Co.,Ltd
Dear Customer,
Thanks for choosing Master machine.
To ensure the safety and proper use of the machine,
please read the instruction book carefully before use.
Also, please fill this card and save it for warranty use.
Buyer Name
Purchase
Time
Tel
Contact
Person
Address
Product
Name
Tamping Rammer
MODEL
FTR80
Motor Model
Note
FOREWARD
◇For your own safety and protection from bodily injuries, carefully read,
understand and follow the safety instructions in this manual.
◇Please operate and maintain your machine in accordance with the
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
3
instructions in this manual.
◇Defective machine parts are to be replaced as soon as possible.
◇Keep this owner's manual handy, so you can refer to it at any time.
◇No part of this publication may be reproduced without written permission.
◇We expressly reserve the right to technical modifications- even without
express due notice - which aim at improving our machines or their safety
standards.
FEATURE
FTR-80 Tamping Rammer adopts the HONDA 4-cycles engine that there
are two air cleaners. The guide handle offers a highly engineered, built-in
shock mount system to reduce HAV (hand-arm vibration) and improve
operator comfort. Utilizing crank shaft and coupling rod configuration
instead of crank and cantilever structure, which improve a great operating
performance and service life. Well balanced performance reduces operator
effort, non key seat design double service life of inner-cylinder body. Easy
for dismounting, and low cost for maintenance.
FTR-80 Series Rammer are ideally suited for the compaction of granular,
detritus, mixed and cohesive soils in confined areas, as well as apply to
asphaltum detritus, concrete and clunch. This model provides reliable,
comfortable use for a variety of applications such as compacting sandy oil,
back fill, asphaltum, road, railroad, bridge, reservoir, dyke, courtyard,
flooring and so on.
SAFETY PRECAUTIONS
1. Before starting operation, the operator has to check that all control and
safety devices function properly.
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
4
2. Exhaust precautions:
a. Never inhale exhaust gasses; They contain
carbon monoxide, a colorless, odorless and
extremely dangerous gas which can cause
unconsciousness or death.
b. Never operate the engine indoors or in a
poorly ventilated area, such as tunnel, cave,
etc.
c. Exercise extreme care when operating the
engine near people or animals.
d. Keep the exhaust pipe free of foreign objects.
3. Refueling precautions:
a. Be sure to stop the engine prior to refueling.
b. Do not overfill the fuel tank.
c. If fuel is spilt, wipe it away carefully and wait until
the fuel has dried before starting the engine.
d. After refueling, make sure that the fuel cap is
secured to prevent spillage.
4. Fire prevention:
a. Do not operator while smoking or near an open flame.
b. Do not use around dry brush, twigs, cloth rags, or
other flammable materials.
c. Keep the engine at least 3 feet (1 meter) away
from buildings or other structures.
d. Keep the engine away from flam-males and other
hazardous materials (trash, rags, lubrications,
explosives).
e. The muffler becomes very hot during
operation and remains hot for a while after
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
5
stopping the engine. Be careful not to touch the muffler while it is
hot. Let the engine cool before storing it indoors.
5. The max gradient of 30° must not be exceeded when the engine
working. Otherwise, the fuel will spilt and the engine oil into the cylinder,
causing engine failure or other hazards.
6. Wear safety shoes, and eye protection glasses in case of trench
operation where falling sand stones maybe ejected.
7. When the machine working, prohibit the operator from the machine.
8. Do not uses to compacting severity harden or hard surface, such as
block, floor slab, cement block.
9. Placed a machine, we should avoid dumping, roll and fall, etc.
TRANSPORTING AND STORAGE
DANGER! Keep the engine lever off when transporting to reduce the
possibility of fuel leakage. Turn the fuel valve lever to the OFF position.
1. Keep the fuel valve lever to OFF position when
transporting.
2. The load-carrying capacity of the loading ramps has to
be sufficient and the ramps have to be secured such that
they cannot turn over. Make sure that no one be endangered
by machines turning over by slipping or by moving machine
parts.
3. Drain the used oil when being transported on vehicles, precautions
have to be taken that vibration plates do not slip or turn over.
The following should be taken to prepare your FTR-80 Tamping
Rammer for extended storage.
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
6
1、Close fuel shut off valve.
2、Store the unit in an upright position in a cool, dry, well
ventilated area.
3、Discharge fuel (NO SMOKING!)
a. Remove the strainer cup, place the strainer over a
container and open the strainer cock to discharge
fuel from the fuel tank.
b. Remove the carburetor float chamber bolt from the
bottom and discharge fuel from the carburetor.
4、Engine oil
a. Change the engine oil fresh oil .
b. Remove the spark plug, pour about 5cc of engine
oil into the cylinder, slowly pull the starter handle
of the recoil starter 2 or 3 times, and reinstall the
spark plug.
5、Clean and store
a. Slowly pull the recoil starter handle until
resistance is felt and leave it in that position.
b. Clean the engines thoroughly with an oiled cloth, put the cover on,
and store the engine indoors in a well-ventilated, low humidity area.
BEFORE OPERATION CHECKS
1. Check for leakage of gasoline and engine oil.
2. Check engine oil
Notice! Running the engine with a low oil level
can cause engine damage.
a. Before checking or refilling engine oil, be
sure the rammer is located on a stable, level
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
7
surface and stopped.
b. Remove the filler cap/dipstick and check the
oil level shown on the dipstick.
c. If the oil level is low, fill to the edge of the oil
filler hole with the recommended oil.
Oil capacity: 0.4L
SAE 10W-30 is recommended for general
use. Other viscosities shown in the chart may
be used when the average temperature in
your area is with the recommended range.
CAUTIONS! Use not depurative lubrication or 2-cycle lubrication can cause
engine damage.
3. Check air cleaner
NOTICE! Operating the engine without an air filter, or with a damaged air
filter, will allow dirt to enter the engine, causing rapid engine wear. This type
of damage is not covered by the Distributor’s Limited Warranty.
4. Check fuel
These engines are certified to operate on unleaded gasoline. Unleaded
gasoline produces fewer engine and spark plug deposits and extends
exhaust system life. Never use stale or contaminated gasoline or an oil
/gasoline mixture. Avoid getting dirt or water in the fuel tank. Occasionally
you may hear a light “spark knock” or “pinging” (metallic raping noise) while
operating under heavy loads. This is no cause for concern. If spark knock
or pinging occurs at a steady engine speed, under normal load, change
brands of gasoline. If spark knock or pinging persists, see an authorized
you’re servicing dealer.
DANGER!
A. Gasoline is highly flammable and explosive.
B. Refuel in a well-ventilated area before starting the engine. If the
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
8
engine has been running, allow it to cool. Gasoline is highly flammable and
explosive.
C. Refuel carefully to avoid spilling fuel. Do not fill the fuel tank
completely. Fill tank to approximately 1 inch (25mm) below the top of the
fuel tank to allow for fuel expansion. It may be necessary to lower the fuel
level depending on operating conditions. After refueling, tighten the fuel
tank cap securely.
D. Be careful not to spill fuel when filling your fuel tank. Damage caused
by spilled fuel is not covered under warranty.
E. Spilled fuel is not only a fire hazard, it causes environmental damage.
Wipe up spills immediately.
F. Keep the children away from the fuel.
5. Check the oil level sight plugs on the Pipe-protective r daily to ensure the
oil is half way on the site glass. Tamping Rammer capacity is 50 oz.
(1600ml). The band of lubrication: SAE10-30.
6. Check fastening screws of protective frame and central suspension for
tight fit.
STARTING THE ENGINE
Turn the STOP SWITCH clockwise to the position “1” (ON).
2. Open the fuel cock.
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
9
3. Close the choke lever.
Notice! If the engine is warm or the ambient temperature is high, open the
choke lever half-way, or keep it fully open. If the engine is cold or the
ambient temperature is low, close the choke lever fully.
4. Set the speed throttle lever at the low speed position.
5.Pull the starter grip lightly until you feel resistance. This is the
“compression” point.
Return the starter grip to its original position and pull swiftly.
Henan Master Machinery Co., Ltd
Tel:(+86)17737606271 www.mastermachinerys.com
10
CAUTION！Do not allow the starter grip to snap back against the engine.
Return it gently to prevent damage to the starter.
After starting the engine, allow the starter grip to return to its original
position while still holding the starter grip.
6、After starting the engine, gradually open choke by turning the choke
lever and finally keep it fully opened.
Notice! Do not fully open the choke lever immediately when the engine is
cold or the ambient temperature is low, because the engine may stop.
Tabla de contenidos
Otros manuales de Apisonadora y apisonadora vibratoria de Master
